Table of Contents
Advertisement
Quick Links
HYBRIDCARE
PUMP DRYER
INSTALLATION
INSTRUCTIONS
Table of Contents
DRYER SAFETY ......................................................................... 2
INSTALLATION REQUIREMENTS ............................................. 3
Tools and Parts ...................................................................... 3
LOCATION REQUIREMENTS .................................................... 4
DRAIN SYSTEM ......................................................................... 5
ELECTRICAL REQUIREMENTS - U.S.A. ONLY ....................... 6
ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ........ 7
INSTALL LEVELING LEGS ......................................................... 8
ELECTRICAL INSTALLATION - U.S.A. ONLY .......................... 8
Power Supply Cord Connection ........................................... 9
Direct Wire Connection ....................................................... 11
CONNECT OUTLET HOSE ...................................................... 14
LEVEL DRYER .......................................................................... 15
COMPLETE INSTALLATION CHECKLIST .............................. 16
DOOR REVERSAL (OPTIONAL) .............................................. 16
TROUBLESHOOTING .............................................................. 20
Para una version de estas instrucciones en español, visite www.Whirlpool.com o www.maytag.com
INSTALLATION NOTES
_________________________________
Date of purchase:
_______________________________
Date of installation:
________________________________________
Installer:
___________________________________
Model number:
___________________________________
Serial number:
HEAT
™
SÉCHEUSE À POMPE À
CHALEUR HYBRIDCARE
INSTRUCTIONS
D'INSTALLATION
Table des matières
SÉCURITÉ DE LA SÉCHEUSE ................................................ 21
EXIGENCES D'INSTALLATION ............................................... 22
Outillage et pièces ............................................................... 22
EXIGENCES D'EMPLACEMENT ............................................. 23
SYSTÈME DE VIDANGE .......................................................... 24
SÉCHEUSE ÉLECTRIQUE RACCORDEMENT
À L'ALIMENTATION ÉLECTRIQUE -
CANADA SEULEMENT ............................................................ 25
INSTALLATION DES PIEDS DE NIVELLEMENT .................... 26
CONNEXION DU TUYAU DE SORTIE ..................................... 26
RÉGLAGE DE L'APLOMB DE LA SÉCHEUSE........................ 27
ACHEVER L'INSTALLATION LISTE DE VÉRIFICATION ......... 28
INVERSION DE LA PORTE (FACULTATIF) .............................. 28
DÉPANNAGE ...................................... COUVERTURE ARRIÈRE
NOTES CONCERNANT L'INSTALLATION
_____________________________________
Date d'achat :
________________________________
Date d'installation :
______________________________________
Installateur :
________________________________
Numéro de modèle :
__________________________________
Numéro de série :
™
W11184511A
W11184519A - SP
Advertisement
Table of Contents
Related Manuals for Whirlpool HYBRIDCARE YWHD560CHW0
Summary of Contents for Whirlpool HYBRIDCARE YWHD560CHW0
-
Page 1: Table Of Contents
INVERSION DE LA PORTE (FACULTATIF) ......28 COMPLETE INSTALLATION CHECKLIST ......16 DÉPANNAGE ........COUVERTURE ARRIÈRE DOOR REVERSAL (OPTIONAL) ..........16 TROUBLESHOOTING .............. 20 Para una version de estas instrucciones en español, visite www.Whirlpool.com o www.maytag.com INSTALLATION NOTES NOTES CONCERNANT L’INSTALLATION _________________________________ _____________________________________ Date of purchase: Date d’achat :... -
Page 2: Dryer Safety
DRYER SAFETY Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized. -
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS TOOLS AND PARTS Parts supplied: Gather the required tools and parts before starting installation. Tools needed: Leveling legs (4) 6' (1.82 m) drain hose with couplers Flat-blade screwdriver #2 Phillips screwdriver Cable ties (2) Wire stripper (direct wire Channel locks Parts package is located in dryer drum. -
Page 4: Location Requirements
LOCATION REQUIREMENTS Check codes requirements. Some codes limit, or do not permit, Side view: installing dryer in garages, closets, mobile homes, or sleeping " quarters. Contact your local building inspector. " min. (1378 mm) (1314 mm) 31" " min. (787 mm) (806 mm) "... -
Page 5: Drain System
DRAIN SYSTEM Installation spacing for recessed area or closet installation: Drain system can be installed using a floor drain, wall standpipe, All dimensions show recommended and minimum spacing allowed. floor standpipe, or laundry tub. Select method you need. ■ Additional spacing should be considered for ease of IMPORTANT: To avoid siphoning, only 4.5"... -
Page 6: Electrical Requirements - U.s.a. Only
Electrical Connection Laundry tub drain system To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. ■ This dryer is manufactured ready to install with a 3-wire 4.5"... -
Page 7: Electric Dryer Power Hookup - Canada Only
■ To supply the required 4-wire, single-phase, 120/240 V, 60 Hz., AC-only electrical supply on a separate 30 amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. -
Page 8: Install Leveling Legs
INSTALL LEVELING LEGS ELECTRICAL INSTALLATION – U.S.A. ONLY Before you start, disconnect power. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to “Power Supply Cord Connection.” Prepare dryer for leveling legs Power supply cord 3-wire receptacle (NEMA Type 10-30R). -
Page 9: Power Supply Cord Connection
Power Supply Cord Connection Attach power supply cord to strain relief Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. - Page 10 Prepare to connect neutral ground Connect remaining wires wire and neutral wire Connect remaining wires under outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover Remove center terminal block screw (B). Remove neutral into slot of dryer rear panel. Secure cover with hold-down ground wire (E) from green external ground conductor screw (A).
-
Page 11: Direct Wire Connection
Direct Wire Connection Connect neutral wire Fire Hazard Use 10 gauge copper wire. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal. Connect neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). - Page 12 Prepare to connect neutral ground Attach direct wire cable to strain relief wire and neutral wire Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in Remove center terminal block screw (B). Remove neutral a horizontal position.
- Page 13 Connect remaining wires Connect neutral wire Place hooked end of neutral wire (white or center) (C) of direct wire cable under Place hooked ends of remaining direct wire cable wires under center terminal block screw (B), hook outer terminal block screws (hooks facing right). Squeeze facing right.
-
Page 14: Connect Outlet Hose
CONNECT OUTLET HOSE Connect neutral ground wire and neutral wire Attach hose Attach the goose-neck fitting of the provided 6 ft. (1.82 m) drain hose to the drain valve at the bottom of dryer back Connect neutral ground wire (E) and neutral wire (white or panel. -
Page 15: Level Dryer
LEVEL DRYER Level dryer Place level here Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture-sensing system to operate correctly. If forward slope of dryer is greater than 1" (25 mm), water could run out from front Plug into a grounded 3 prong outlet of filter. -
Page 16: Complete Installation Checklist
COMPLETE INSTALLATION DOOR REVERSAL (OPTIONAL) CHECKLIST The following instructions are for models with round doors. Tools needed: Ɨ Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. Ɨ... - Page 17 ALL DOORS: Remove inner door from outer door Remove door from dryer Top of door IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Position the door with the inside of the door facing up. Using a T25 screwdriver, remove the four screws securing ®...
- Page 18 Remove latch Reinstall hinge assembly on opposite side Thin section Latch Thick section Flip and rotate the inner door 180° so that the thin section is Flip over the inner door to the left. Using a T20 screwdriver, ® at the top and the thick section is at the bottom. Using a T25 reinstall the hinge assembly on the opposite side from which ®...
- Page 19 ALL DOORS: Reposition rotating assembly and tubing Reinstall inner door assembly Swing down Reposition rotating assembly and tubing 180 ° to opposite side Bottom of the door. of door Rotate assembly bottom and fasten Position the door with the inside of the door facing up. Using a Phillips screwdriver, reinstall the 10 screws removed earlier, in place securing the inner door to the outer door.
-
Page 20: Troubleshooting
TROUBLESHOOTING DOORS WITH LCD SCREEN: See the Use and Care Guide or visit our website and reference Frequently Asked Questions to possibly avoid the cost of a Reconnect wiring service call. Plug in wire. Using a Phillips screwdriver, secure the rotating assembly to the hinge with the screw removed earlier.