ICT PRX-TSEC-STD-B Installation Manual

ICT PRX-TSEC-STD-B Installation Manual

Tsec multi-technology card reader with bluetooth wireless technology

Advertisement

tSec Reader Range
tSec Multi-Technology Card Reader with
Bluetooth® Wireless Technology
Installation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRX-TSEC-STD-B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ICT PRX-TSEC-STD-B

  • Page 1 tSec Reader Range tSec Multi-Technology Card Reader with Bluetooth® Wireless Technology Installation Manual...
  • Page 2 The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited.
  • Page 3: Table Of Contents

    RS-485 Reader Connection (Entry/Exit) OSDP Reader Connection OSDP Baud Rate Requirement Reader Addressing Programming the Card Reader Protege Config App MIFARE Config Card ICT Encoder Client 125kHz Programming Card Technical Diagrams tSec Standard Reader tSec Extra Reader tSec Mini Reader Reader Comparison...
  • Page 4 Technical Specifications New Zealand and Australia European Standards UK Conformity Assessment Mark UL and ULC Installation Requirements CAN/ULC-S319 UL 294 FCC Compliance Statements Industry Canada Statement OSDP Verified Logo Disclaimer and Warranty tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 5: Introduction

    Introduction This installation manual provides instructions and technical specifications for physical installation of the ICT tSec Multi-Technology Card Reader. For programming information, see the ICT Card Reader Configuration Guide, available from the ICT website. About This Module The tSec Multi-Technology Card Reader is an advanced-technology, high-frequency smart card radio frequency identification device (RFID), specifically designed to enhance the functionality of security, building automation and access control by providing multiple format compatibility, high-speed data transmission and sabotage protection.
  • Page 6: Reader Editions

    117 x 46 x 18mm (4.61 x 1.81 x 0.71") MIFARE/ Vandal Bluetooth® Keypad 125kHz DESFire/ Resistant Technology Cover* PRX-TSEC-STD-B tSec Standard Multi-Technology Card Reader PRX-TSEC-STD-KP-B tSec Standard Multi-Technology Card Reader with Keypad PRX-TSEC-STD-125-B tSec Standard 125kHz Card Reader PRX-TSEC-STD-DF-B tSec Standard 13.56MHz Card Reader PRX-TSEC-STD-DF-KP-B tSec Standard 13.56MHz Card Reader with...
  • Page 7 Extra 117 x 75x 18mm (4.61 x 2.95 x 0.71") MIFARE/ Vandal Bluetooth® Keypad 125kHz DESFire/ Resistant Technology Cover* PRX-TSEC-EXTRA-KP-B tSec Extra Multi-Technology Card Reader with Keypad PRX-TSEC-EXTRA-125-B tSec Extra 125kHz Card Reader PRX-TSEC-EXTRA-DF-B tSec Extra 13.56MHz Card Reader PRX-TSEC-EXTRA-DF-KP-B tSec Extra 13.56MHz Card Reader with Keypad PRX-TSEC-EXTRA-BT-B PRX-TSEC-EXTRA-BT-W...
  • Page 8 Mini 85 x 46 x 17mm (3.35 x 1.81 x 0.67”) MIFARE/ Vandal Bluetooth® Keypad 125kHz DESFire/ Resistant Technology Cover* PRX-TSEC-MINI-B tSec Mini Multi-Technology Card Reader PRX-TSEC-MINI-125-B tSec Mini 125kHz Card Reader PRX-TSEC-MINI-DF-B tSec Mini 13.56MHz Card Reader PRX-TSEC-MINI-BT-B PRX-TSEC-MINI-BT-W tSec Mini Multi-Technology Card Reader with Bluetooth®...
  • Page 9: Mifare Technology

    MIFARE Technology About MIFARE Based on the international standard ISO/IEC 14443 Type A, MIFARE is a technology used for contactless RFID smart card systems consisting of card and reader components. ⦁ Fully compliant with the international standard ISO/IEC 14443 Type A ⦁...
  • Page 10: About Mifare Desfire Ev3

    MIFARE/DESFire Products The MIFARE/DESFire products can be expanded to accommodate large numbers of modules using the encrypted RS-485 Network. ICT provides a number of reader and physical credential options in the MIFARE/DESFire range, including MIFARE Classic and MIFARE DESFire EV1, EV2 and EV3.
  • Page 11: Installation Requirements

    Installation Requirements This equipment is to be installed in accordance with: The product installation instructions ⦁ UL 681 - Installation and Classification of Burglar and Holdup Systems ⦁ UL 827 - Central-Station Alarm Services ⦁ CAN/ULC-S301, Central and Monitoring Station Burglar Alarm Systems ⦁...
  • Page 12: Mounting

    Mounting The card reader provides the reading component of access control, time and attendance and alarm systems. It is intended to be mounted on a wall with adequate air flow around and through it. Mounting Instructions Cables are intended to be run inside the wall. If cables are to be run through external conduits you must use the surface mount box accessory (see below).
  • Page 13 Clip the upper rim of the front case over the upper rim of the surface mount box, then press gently on the front case until the lower rim slots over the lower rim of the surface mount box, lining up the screw hole at the bottom.
  • Page 14 Affix the rear case to the surface mount box using the two M4 x 10mm screws provided. Connect the wiring to the reader electronics through the conduit hole. Refer to later sections of this manual for the wiring connections. Clip the upper rim of the front case over the upper rim of the rear case, then press gently on the front case until the lower rim slots over the lower rim of the rear case, lining up the screw hole at the bottom.
  • Page 15: Reader Connection

    Reader Connection Using the recommended cables, splice the cable together with the pigtail of the reader and seal the splice. Route the cable from the reader to the host module. Connect the cable to the module port according to the required operation, as shown in the connection diagrams that follow.
  • Page 16: Wiegand Reader Connection

    Readers also need to be programmed to operate in dual LED mode. For programming instructions, see the Card Reader Configuration Guide, available from the ICT website. Compatible access control card reader communication formats are: 26-, 34-, and 37-bit Wiegand. tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 17: Wiegand Reader Connection (Entry / Exit)

    Wiegand Reader Connection (Entry / Exit) In multiple reader mode, the secondary reader has all connections wired to the same port as the primary card reader, with the DATA 1 connection wired to the opposite reader connection DATA 1 input. The reader that is multiplexed into the alternate reader port will operate as the exit reader, and the normal reader connection operates as the entry reader.
  • Page 18: Rs-485 Reader Connection

    RS-485 Reader Connection The connection of a single RS-485 reader to a reader expander. Reader shield is Shield wires SHIELD not terminated connected inside the reader at the splice BLACK Shielded Cable GREEN WHITE ORANGE BROWN Shield is frame BLUE grounded at YELLOW one point...
  • Page 19: Osdp Reader Connection

    Readers must also be programmed to operate in OSDP mode. For more information, see Programming the Card Reader (page 21). For more information about OSDP support on ICT card readers, including configuring readers for secure channel communications, see Application Note 321: Configuring ICT Readers for OSDP Communication.
  • Page 20: Reader Addressing

    Reader Addressing For a card reader operating in OSDP mode to be recognized on a third-party system, the reader address may need to be configured to meet the third-party system's addressing requirements. For the tSec range of card readers the address and addressing options are determined by the reader's wiring configuration.
  • Page 21: Programming The Card Reader

    Programming options are dependent on hardware compatibility and firmware versions. Important: ICT card readers can only be programmed within 2 minutes of startup. In order to program the reader you will need to disconnect power and complete programming within 2 minutes of powering up.
  • Page 22: Mifare Config Card

    When programming is successful, the reader will beep 5 times quickly then restart. ICT Encoder Client The ICT Encoder Client is a software application that allows users to encode credentials for use with their ICT card readers, Protege access control system, and optionally other third-party systems.
  • Page 23: 125Khz Programming Card

    Once complete, allow the programming interface to time out and return to normal operation. For detailed information on programming ICT card readers using a 125kHz programming card, including the available programming options and badging sequences, see the ICT Card Reader Configuration Guide, available from the ICT website.
  • Page 24: Technical Diagrams

    Technical Diagrams tSec Standard Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT tSec Standard reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 4.5mm Screw Hole ø...
  • Page 25: Tsec Extra Reader

    Extra Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT tSec Extra Reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 4.5mm Screw Hole ø 10mm Cable Hole ø...
  • Page 26: Tsec Mini Reader

    Mini Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT tSec Mini reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 10mm Cable Hole ø 4.5mm Screw Hole 23.00...
  • Page 27: Reader Comparison

    Reader Comparison The dimensions shown below provide a direct comparison of the reader models. 4.5mm Screw Hole 4.5mm Screw Hole 10mm Cable Hole 10mm Cable Hole 4.5mm Screw Hole 4.5mm Screw Hole 46mm / 1.81” 75mm / 2.95” tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 28: Technical Specifications

    Technical Specifications The following specifications are important and vital to the correct operation of this product. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void. Ordering Information Order Codes See Reader Editions.
  • Page 29 Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest documentation and product information. tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 30: New Zealand And Australia

    New Zealand and Australia Intentional Transmitter Product Statement The R-NZ compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 31: European Standards

    European Standards CE Statement Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast (RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863. This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self Declaration of the CE Marking for the European Union as specified in the above directive(s).
  • Page 32: Uk Conformity Assessment Mark

    UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards. tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 33: Ul And Ulc Installation Requirements

    Performance Levels Destructive Attack Line Security Endurance Standby Power Level I when wired with Wiegand ICT Standard Reader Level I Level IV Level I Level IV when wired with RS485 Level I when wired with Wiegand...
  • Page 34: Fcc Compliance Statements

    FCC Compliance Statements FCC PART 15, WARNINGS: INFORMATION TO USER This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 35: Industry Canada Statement

    Industry Canada Statement This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CAN ICES-3 (A)/NMB-3(A) tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 36: Osdp Verified Logo

    OSDP Verified Logo Open Supervised Device Protocol (OSDP) Verified Certification The OSDP Verified logo indicates that this device is compliant with the OSDP 2.2 PD Secure profile and all applicable standards. tSec | tSec Multi-Technology Card Reader with Bluetooth® Technology | Installation Manual...
  • Page 37: Disclaimer And Warranty

    Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.
  • Page 38 In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.

Table of Contents