Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ICT TSL-STD-RR-HL
Summary of Contents for ICT TSL-STD-RR-HL
- Page 1 TSL Reader Range TSL Multi-Technology Card Reader Installation Manual...
- Page 2 The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited.
-
Page 3: Table Of Contents
Contents Introduction About This Module Reader Editions Reader Accessories Faceplates Vandal Resistant Cover Surface Mount Box Pigtail Cables Ferrite Shield MIFARE Technology About MIFARE Secured MIFARE Card Format About MIFARE DESFire EV1 About MIFARE DESFire EV2 About MIFARE DESFire EV3 MIFARE/DESFire Products Installation Requirements Mounting... - Page 4 Enabling Wiegand Mode Programming the Card Reader Protege Config App Technical Diagrams TSL Standard Reader TSL Extra Reader TSL Mini Reader TSL Standard Reader Vandal Resistant Cover TSL Extra Reader Vandal Resistant Cover Technical Specifications New Zealand and Australia European Standards UK Conformity Assessment Mark UL and ULC Installation Requirements CAN/ULC-S319...
-
Page 5: Introduction
Introduction This installation manual provides instructions and technical specifications for physical installation of the ICT TSL Multi-Technology Card Reader. For programming information, see the ICT Card Reader Configuration Guide, available from the ICT website. About This Module The TSL Multi-Technology Card Reader is an advanced-technology, high-frequency smart card radio frequency identification device (RFID), specifically designed to enhance the functionality of security, building automation and access control by providing multiple format compatibility, high-speed data transmission and sabotage protection. -
Page 6: Reader Editions
117 x 43 x 9.5mm (4.61 x 1.69 x 0.37") MIFARE/ Bluetooth® Keypad 125kHz DESFire/ Technology TSL-STD-RR-HL TSL Standard Multi-Technology Card Reader with Bluetooth® Wireless Technology TSL-STD-RK-HL TSL Standard Multi-Technology Card Reader with Bluetooth® Wireless Technology and Keypad TSL-STD-RR-H TSL Standard 13.56MHz Card Reader with Bluetooth®... - Page 7 Mini 87 x 43 x 9.5mm (3.43 x 1.69 x 0.37”) MIFARE/ Bluetooth® Keypad 125kHz DESFire/ Technology TSL-MINI-RR-HL TSL Mini Multi-Technology Card Reader with Bluetooth® Wireless Technology TSL-MINI-RR-H TSL Mini 13.56MHz Card Reader with Bluetooth® Wireless Technology TSL-MINI-RR-L TSL Mini 125kHz Card Reader with Bluetooth®...
-
Page 8: Reader Accessories
Reader Accessories A number of optional accessories are available to complement your TSL reader installation. Faceplates All TSL readers are shipped with a black faceplate. To switch to a white reader simply order a white faceplate. Whether you're looking for a color change or need to replace a damaged cover, replacement white and black faceplates are available to suit all TSL reader sizes and configurations. -
Page 9: Vandal Resistant Cover
Vandal Resistant Cover The vandal resistant cover (VRC) accessory is ideal for locations where a card reader may be exposed to damage, including corridors, parking buildings, correctional facilities, and other public places. Highly resistant to impact, such as from the swing of a hammer or baseball bat, its robust construction provides greater durability and protection against vandalism and malicious damage. -
Page 10: Pigtail Cables
Pigtail Cables TSL readers use a shielded 8-wire pigtail wiring loom with a Hirose socket plug for connection to the reader. A standard 34cm cable is supplied with the reader, while a 3.5m long cable option is also available. The 3.5m pigtail cable is not compliant for UL/ULC installations. Ordering Codes Accessory Ordering Code... -
Page 11: Mifare Technology
MIFARE Technology About MIFARE Based on the international standard ISO/IEC 14443 Type A, MIFARE is a technology used for contactless RFID smart card systems consisting of card and reader components. ⦁ Fully compliant with the international standard ISO/IEC 14443 Type A ⦁... -
Page 12: About Mifare Desfire Ev3
MIFARE/DESFire Products The MIFARE/DESFire products can be expanded to accommodate large numbers of modules using the encrypted RS-485 Network. ICT provides a number of reader and physical credential options in the MIFARE/DESFire range, including MIFARE Classic and MIFARE DESFire EV1, EV2 and EV3. -
Page 13: Installation Requirements
Installation Requirements This equipment is to be installed in accordance with: The product installation instructions ⦁ UL 681 - Installation and Classification of Burglar and Holdup Systems ⦁ UL 827 - Central-Station Alarm Services ⦁ CAN/ULC-S301, Central and Monitoring Station Burglar Alarm Systems ⦁... -
Page 14: Mounting
Use the drill template sticker provided with the card reader as a guide to correctly position the unit and drill the necessary holes as instructed. The drill template is also available from the ICT website. The reader's cable connection socket should align with the 'connector' hole cut through the wall. Cables are intended to be run inside the wall. - Page 15 Screw heads must not protrude above the mounting hole cavity Moun n g screws ¡ Connec o n socket ¡ Accessories Provided ⦁ 1 x shielded 8-wire wiring loom with waterproof Hirose socket plug ⦁ 1 x M3(G4)x4 PanPozi Plastite SS316 stainless steel self-tapping screw Accessories Not Included ⦁...
-
Page 16: Mounting With Vandal Resistant Cover Accessory
Use the drill template sticker provided with the card reader as a guide to correctly position the unit and drill the necessary holes as instructed. The drill template is also available from the ICT website. The reader's cable connection socket should align with the 'connector' hole cut through the wall. Cables are intended to be run inside the wall. - Page 17 Vandal-proof Silicone Seal Before installing the vandal resistant cover, silicone is applied along the top and side edges of the card reader to ensure a sealed vandal-proof installation and maintain the impact protection rating. The silicone is applied after the reader has been mounted, forming an exact fit at the mounting location. Ensure that the bottom of the reader is not sealed, so that the faceplate can still be removed.
-
Page 18: Mounting With Surface Mount Box Accessory
Mounting with Surface Mount Box Accessory The optional surface mount box (SMB) accessory enables you to mount the card reader projected from the wall, allowing space for cabling from external conduits. The surface mount box is the same height and width as the card reader rear case, with a protected cavity to allow external cabling to be securely connected to the reader. - Page 19 Hold the rear case of the card reader against the surface mount box in the correct orientation. Line up the holes on the rear case with the threaded inserts closest to the center of the surface mount box, as shown in the image below.
-
Page 20: Reader Connection
Reader Connection Using the recommended cables, splice the cable together with the pigtail of the reader and seal the splice. Route the cable from the reader to the host module. Connect the cable to the module port according to the required operation, as shown in the connection diagrams that follow. -
Page 21: Shield Connection
Shield Connection Connect the reader pigtail shield and cable shield wires together at the reader pigtail splice. Connect the cable shield to a suitable earth point. Do not connect the shield to a ground or AUX connection. The reader pigtail shield wire is not terminated inside the reader. Important: The card reader must be connected to the module port using a shielded cable. -
Page 22: Rs-485 Reader Connection
RS-485 Reader Connection The connection of a single RS-485 reader to a reader expander. Reader Connections Color Wire Connection V+ 12VDC positive Black V- 12VDC negative Yellow D0/NA RS-485 A Violet D1/NB RS-485 B Shield Shield (drain) wire. Frame grounded at one point only TSL Multi-Technology Card Reader | Installation Manual... -
Page 23: Rs-485 Reader Connection (Entry/Exit)
RS-485 Reader Connection (Entry/Exit) The connection of two RS-485 readers to a reader expander providing an entry/exit configuration. A 330 ohm EOL (End of Line) resistor be required, inserted between the yellow and violet wires after the join. When connecting two TSL readers for RS-485 entry/exit configuration, the reader address determines which is the entry reader and which is the exit reader, so it does not matter which reader is the 'secondary' connection. -
Page 24: Rs-485 Reader Location
For programming information, see the ICT Card Reader Configuration Guide, available from the ICT website. The address and addressing options of TSL card readers is not determined by the reader's wiring configuration. TSL Multi-Technology Card Reader | Installation Manual... -
Page 25: Osdp Reader Connection
For more information, see Application Note 254: Configuring OSDP Readers in Protege. For more information about OSDP support on ICT card readers, including configuring readers for secure channel communications, see Application Note 321: Configuring ICT Readers for OSDP Communication. -
Page 26: Osdp Baud Rate Requirement
The Config App Reader Configuration will need a config with the Uart Configuration TLV selected, with the Baud set to match the connected reader port. For detailed information on programming ICT card readers, see the ICT Card Reader Configuration Guide, available from the ICT website. -
Page 27: Wiegand Reader Connection
Wiegand Reader Connection When connected using the Wiegand interface, TSL readers operate in single LED mode, which allows a single LED line to control the two reader LED colors. TSL readers do not support dual LED operation for Wiegand interfaces. Reader Connections Color Wire Connection... -
Page 28: Wiegand Reader Connection (Entry / Exit)
Wiegand Reader Connection (Entry / Exit) In multiple reader mode, the secondary card reader has all connections wired to the same reader port as the primary reader, except the Data 1 connection which is wired to the Data 1 input on the alternate reader port. The normal primary reader connection operates as the entry reader, and the secondary reader that is multiplexed into the alternate reader port will operate as the exit reader. -
Page 29: Connecting 4 Wiegand Readers
Protege Config App. The Config App's Reader Configuration will need a config with the Output Mode set to Wiegand Output. For programming instructions, see the ICT Card Reader Configuration Guide, available from the ICT website. TSL Multi-Technology Card Reader | Installation Manual... -
Page 30: Programming The Card Reader
Programming the Card Reader ICT readers can be programmed for a wide range of functionality to suit your site's requirements. Programming options are dependent on hardware compatibility and firmware versions. Card reader programming is configured by applying specific TLV (Type Length Value) settings to the reader to enable, disable and configure reader options. -
Page 31: Technical Diagrams
Technical Diagrams TSL Standard Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Standard Reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 18mm Connector Hole (Min) ø... -
Page 32: Tsl Extra Reader
TSL Extra Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Extra Reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 18mm Connector Hole (Min) ø 4.5mm Screw Hole 37.5... -
Page 33: Tsl Mini Reader
TSL Mini Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Mini Reader. All measurements are shown in millimeters. ø 4.5mm Screw Hole ø 1 8 m m Connector H ole (M in) ø... -
Page 34: Tsl Standard Reader Vandal Resistant Cover
TSL Standard Reader Vandal Resistant Cover The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Standard Reader Vandal Resistant Cover. All measurements are shown in millimeters. 89.00m m 3.504in 11.70m m 0.461in 5.3m m 0.207in... -
Page 35: Tsl Extra Reader Vandal Resistant Cover
TSL Extra Reader Vandal Resistant Cover The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Extra Reader Vandal Resistant Cover. All measurements are shown in millimeters. 121.00mm 4.764in 11.70m m 0.461in 5.3m m 0.207in... -
Page 36: Technical Specifications
Technical Specifications The following specifications are important and vital to the correct operation of this product. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void. Ordering Information Order Codes See Reader Editions. - Page 37 Android 4.4 or above, with phones which support ISO7816-4 NFC (Near-field communication) Proprietary Secured DESFire credential electronic credential transmission Credential is AES-256 (NIST certified AES algorithm) technology Credentials can be distinguished by unique site code and card number NFC Wireless Device Protege Mobile 1.0.x Operating Conditions Environment IP Rating...
- Page 38 Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest documentation and product information. TSL Multi-Technology Card Reader | Installation Manual...
-
Page 39: New Zealand And Australia
New Zealand and Australia Intentional Transmitter Product Statement The R-NZ compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. TSL Multi-Technology Card Reader | Installation Manual... -
Page 40: European Standards
European Standards CE Statement Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast (RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863. This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self Declaration of the CE Marking for the European Union as specified in the above directive(s). -
Page 41: Uk Conformity Assessment Mark
UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards. TSL Multi-Technology Card Reader | Installation Manual... -
Page 42: Ul And Ulc Installation Requirements
Performance Levels Destructive Attack Line Security Endurance Standby Power Level I when wired with Wiegand ICT Standard Reader Level I Level IV Level I Level IV when wired with RS485 Level I when wired with Wiegand... -
Page 43: Fcc Compliance Statements
FCC Compliance Statements FCC PART 15, WARNINGS: INFORMATION TO USER This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 44: Industry Canada Statement
Industry Canada Statement This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CAN ICES-3 (A)/NMB-3(A) TSL Multi-Technology Card Reader | Installation Manual... -
Page 45: Disclaimer And Warranty
Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice. - Page 46 In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.