Summary of Contents for SNOWJOE sunjoe 24V-PS8-LTE-RM
Page 1
Form No. SJ-24V-PS8-LTE-RM-880E-V1 Form No. SJ-SPX3000-RM-880E-V1 THANKS YOUR PURCHASE OF A REMANUFACTURED PRODUCT. To make sure you get the most out of your product, be sure to register online at snowjoe.com to enjoy full product support. PASTE UPC LABEL HERE...
® ® personal injury from the cutting blades or chain. at 1-866-SNOWJOE (1-866-766-9563) for all maintenance 23. Hold the product by insulated gripping surfaces only, or operations not foreseen in this manual. Any operation because the cutting blade or chain may contact hidden performed in an unauthorized service center or by unqualified wiring.
Storage Kickback WARNING ! Kickback may occur when the nose or tip WARNING! Do not at any time let brake fluids, gasoline, of the guide bar touches an object, or when the wood closes petroleum-based products, penetrating oils, etc., come in in and pinches the saw chain in the cut.
Page 5
® ® • Avoid dangerous environments – Do not charge the 1-866-SNOWJOE (1-866-766-9563) for assistance. battery pack in rain, snow or in damp or wet locations. • Battery chemicals cause serious burns – Never let a Do not use the battery pack or charger in the presence of damaged battery pack contact the skin, eyes or mouth.
+ Sun Joe ® ® ® or the electronic protection system triggers. Place customer service center at 1-866-SNOWJOE the battery pack in storage only after it has been fully (1-866-766-9563). charged. 3. Electrical plugs must match the outlet. Never modify 8.
12. Never fully discharge the battery pack (maximum recommended depth of discharge is 80%). A complete discharge of the battery pack will lead to premature aging of the battery cells. Protection from environmental influences 1. Wear suitable work clothes. Wear safety goggles. 2.
Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols Descriptions READ THE OPERATOR'S MANUAL(S) – Read, understand, SAFETY ALERT –...
Know Your Cordless Pole Chain Saw Read the owner’s manual and safety instructions carefully before operating the cordless pole chain saw. Compare the illustration below to the cordless pole chain saw in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
® ® a few minutes later. The battery cells “recover” some of their 1-866-SNOWJOE (1-866-766-9563). charge after resting. NOTE: Do not discard the shipping carton and packaging Charger Operation material until you are ready to use your new cordless pole chain saw.
Charging the Battery IMPORTANT! Never allow the battery pack to become fully discharged as this will cause irreversible damage to the 1. Push the push lock button on the battery to pull the battery. battery pack out from the battery compartment (Fig. 1). Assembly Fig.
Page 12
NOTE: Make certain of the direction of the chain Fig. 5 . If the chain is mounted backwards, the saw will vibrate abnormally and will not cut. Fig. 8 Chain/sprocket end cover 3. Remove the bar and chain from the mounting surface (Fig.
NOTE: The chain is correctly tensioned when there is no 3. To remove the chain saw head, release the On/Off trigger sag on the underside of the guide bar; the chain is snug, switch and remove the battery. Unlock the assembly lock. but can be rotated by hand without binding.
Page 14
Back Side Fig. 16 Fig. 19 Pull Pull Rotating button Front Side Telescoping lock 3. Lock the pole in position by closing the telescoping lock Rotating button (Fig. 17), and ensure that the pole is secured. Fig. 17 2. Release the buttons when the chain saw head is set to the desired angle.
Page 15
A good, firm grip on the tool using both hands will help you can cause loss of saw control, which can throw the operator off balance and result in serious injury. Do not rely exclusively maintain control. Place one hand on the soft grip or the telescoping pole, and the other hand on the handle with your upon the safety devices built into the saw.
Limbing • Squeeze the On/Off trigger switch and let the chain accelerate to full speed before entering the cut. Limbing is the process of removing branches from a fallen tree. • Keep the saw running the entire time you are cutting; •...
Page 17
Snow Joe + Sun Joe dealer or call the Snow Joe ® ® ® Sun Joe customer service center at 1-866-SNOWJOE ® (1-866-766-9563). Inspection tool Depth limiter Sharpening is necessary when: tooth •...
If you continue to experience problems or need repairs beyond these minor Replace a bar with any of the following faults: adjustments, please call 1-866-SNOWJOE (1-866-766-9563) • wear inside the bar rails permitting the chain to for assistance.
1. Batteries vary according to device. Consult your manual ® ® ® for specific information. Sun Joe customer service center at 1-866-SNOWJOE ® (1-866-766-9563) before using it. 2. Install only new batteries of the same type in your product (where applicable). CAUTION! 3.
Model + Serial Number When contacting the company, reordering parts, or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe + Sun Joe to provide notice of such ® ® changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe + Sun Joe customer ® ® service center at 1-866-SNOWJOE (1-866-766-9563).
Page 23
Certain products may require a serial your state. or guard of your product. All products require a valid proof HOW TO REACH US: of purchase. and Sunday 9AM to 4PM. You can reach us at 1-866-SNOWJOE EXCLUSIONS: (1-866-766-9563), online snowjoe.com, email help@snowjoe.com or tweet us @snowjoe.
Need help?
Do you have a question about the sunjoe 24V-PS8-LTE-RM and is the answer not in the manual?
Questions and answers