La Crosse Technology WS2307 Operation Manual page 15

Pressure high alarm and low alarm setting
1) Press the ALARM key to enter the normal time alarm
2) Continue to press the ALARM key until you reach the pressure
high alarm set mode
3) Press and hold the SET key to enter the pressure setting values
(digits will start flashing) and set the desired pressure high by us-
ing the PLUS(+) or MINUS (-) keys
4) Press ALARM key to confirm and press the MIN/MAX key to re-
turn to the normal display mode or press the ALARM key once
more to toggle to the pressure low alarm set mode.
5) Press and hold the SET key to enter the pressure low setting
values (digits will start flashing) and set the desired pressure low
by using the PLUS(+) or MINUS(-) keys
6) Press ALARM key to confirm and press the MIN/MAX key to re-
turn to the normal display mode or press the ALARM once more to
toggle to another alarm setting mode.
Wind speed high alarm and low alarm setting
1) Press the ALARM key to enter the normal time alarm
2) Continue to press the ALARM key until you reach the wind speed
high alarm set mode
3) Press and hold the SET key to enter the wind speed setting values
(digits will start flashing) and set the desired wind speed high by
using the PLUS(+) or MINUS (-) keys
4) Press ALARM key to confirm and press the MIN/MAX key to re-
turn to the normal display mode or press the ALARM key once
more to toggle to the wind speed low alarm set mode.
5) Press and hold the SET key to enter the wind speed low setting
values (digits will start flashing) and set the desired pressure low
by using the PLUS(+) or MINUS(-) keys
6) Press ALARM key to confirm and press the MIN/MAX key to re-
turn the normal display mode or press the ALARM once more to
toggle to another alarm setting mode.
Wind direction alarm setting
1) Press the ALARM key to enter the normal time alarm
2) Continue to press the ALARM key until you reach the wind direc-
tion alarm set mode
3) Press and hold the SET key to enter the wind direction setting
values.
4) Using the PLUS(+) or MINUS (-) keys select the desired wind
direction and use the SET key to confirm or cancel each direction
input
5) Press ALARM key to confirm and press the MIN/MAX key to re-
turn the normal display mode or press the ALARM once more to
toggle to another alarm setting mode.
Storm warning alarm setting
Unlike the other weather alarms, the storm warning alarm is set by
entering the main manual setting mode as follows:
10) Press the SET key to enter the manual setting mode
11) Continue to press the SET key until the Storm warning icon
flashes (tendency arrow flashing downwards with the pressure
values flashing)
12) Set the desired hPa pressure value (3 hPa - 9 hPa) using the
PLUS(+) or MINUS(-) keys
13) Press the MIN/MAX key to confirm and return to the normal dis-
play.
Storm warning alarm ON/OFF
After storm warning alarm setting, the next mode to appear after
pressing the SET key is the storm warning ON/OFF. Use the
PLUS(+) or MINUS(-) key to change the status to AON or AOFF.
Default setting is ON:
Should the air pressure drop equal or below the pre-set hPa value
within the last 6 hour period, then the downward tendency arrow will
flash as an indication of possible storm. The base station will take
hourly measurements as a point of reference. The storm-warning
indicator will stop flashing once the air pressure becomes more sta-
ble.
Master Alarm – BUZZER OFF
The time and all the weather alarms may have buzzer sound set to
OFF by holding the MINUS(-) key down for about 3 seconds in normal
display mode and the BUZZER OFF icon appears on the bottom left
of the LCD. When the BUZZER OFF is displayed, the time and all
other weather alarms when activated will only flash but not sound
regardless if that particular alarm has been set to the ON. To deacti-
vate the BUZZER OFF, press the MINUS(-) key once more.