Page 8
NOTE: The more slanted side of the V foot should be closer to the end of the crossbow. HARDWARE USED 16× hand tighten the nuts Carriage bolts are already on the crossbows. #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 1525-PC Installation Guide | REV. B2 | Page 8 For technical support, contact us at 1-800-565-5321...
Page 9
Marker HARDWARE USED 4× Carriage bolts are already on the crossbows. #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 12 - 3/4" 1525-PC Installation Guide | REV. B2 | Page 9 For technical support, contact us at 1-800-565-5321...
Page 10
Cutter HARDWARE USED 4× hardware is pre assembled #90-491 Carriage Bolt 5/16" × 1" #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 1525-PC Installation Guide | REV. B2 | Page 10 For technical support, contact us at 1-800-565-5321...
Page 11
Cordless Impact q 1/2" Socket HARDWARE USED 4× Carriage bolts are already on the ski. #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 1525-PC Installation Guide | REV. B2 | Page 11 For technical support, contact us at 1-800-565-5321...
Page 12
HARDWARE USED 4× hand tighten the nuts #90-491 Carriage Bolt 5/16" × 1" #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 1525-PC Installation Guide | REV. B2 | Page 12 For technical support, contact us at 1-800-565-5321...
Page 13
TOOLS q Mallet HARDWARE USED 6× #90-491 Carriage Bolt 5/16" × 1" SS304 1525-PC Installation Guide | REV. B2 | Page 13 For technical support, contact us at 1-800-565-5321...
Page 14
#98-123 Lock Washer #94-105 Hex Nut 2× Carriage bolts are already on the ski. #98-160 Spacer #98-117 Flat Washer #98-123 Lock Washer #94-105 Hex Nut 1525-PC Installation Guide | REV. B2 | Page 14 For technical support, contact us at 1-800-565-5321...
Cordless Impact q 10mm Socket HARDWARE USED 10× #90-825 Hex Bolt M6 × 20mm #98-119 Lock Washer #98-113 Flat Washer #98-149 Neoprene Spacer 1525-PC Installation Guide | REV. B2 | Page 15 For technical support, contact us at 1-800-565-5321...
Page 16
2.2.1 Position the Ladder Rack ( minimum two persons ) on the vehicle so that the feet are on the tracks. NOTE: If you do not have a hoist, lift the ladder rack onto the roof manually. Ladder Rack 1525-PC Installation Guide | REV. B2 | Page 16 For technical support, contact us at 1-800-565-5321...
Page 18
2.2.3 Center the crossbows on the vehicle, then tighten all the “V” feet to the crossbows. TOOLS q Ratchet q 1/2" Socket 1525-PC Installation Guide | REV. B2 | Page 18 For technical support, contact us at 1-800-565-5321...
Page 19
Now adjust the front hook to be snug against the ladder rung and tighten the bolts on the front crossbow. TOOLS q Cordless Impact q 1/2" Socket front hook 1525-PC Installation Guide | REV. B2 | Page 19 For technical support, contact us at 1-800-565-5321...
Page 20
The inner ladder side support must be adjusted according to the width of the step ladder. 1525-PC Installation Guide | REV. B2 | Page 20 For technical support, contact us at 1-800-565-5321...
Page 21
If the handle is interfering with the door or roof of the vehicle, disassemble the handle, then assemble it in an alternate position as shown. Handle 1525-PC Installation Guide | REV. B2 | Page 21 For technical support, contact us at 1-800-565-5321...
Page 22
“You have successfully installed your 1525-PC Ladder Rack Thank you for doing business with us.” cs@rangerdesign.com For any feedback or suggestions you may have, please contact: 1525-PC Installation Guide | REV. B2 | Page 22 For technical support, contact us at 1-800-565-5321...