Related Manuals for Miele CS 1012
Summary of Contents for Miele CS 1012
- Page 1 Operating and Installation Instructions Gas Combiset CS 1012 ® ® en - US, CA To prevent accidents and appliance damage, read these instructions before installation or use. M.-Nr. 07 366 180...
- Page 2 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 4 Guide to the combiset ..........9 Before using the combiset . -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Children WARNING- When using your gas Children should not be left appliance follow basic unattended in an area where the precautions, including the appliance is in use. Never allow following: children to sit or stand on any part of the appliance. - Page 5 Install the appliance so that the power cord and gas piping do not Installation, repair and maintenance come into contact with any portion of work should be performed by a Miele the combiset which may become hot authorized service technician. Work by during use.
- Page 6 Do not let the potholder applications. Please contact the touch the hot heating elements. Do not nearest Miele Dealer or the Miele use towels or other bulky items near the Technical Service Department with appliance.
- Page 7 IMPORTANT SAFETY INSTRUCTIONS Do not use pans that extend past Always position pan handles and the burner grate. Using larger pans utensils inward so they do not extend may cause the flames to spread out over adjacent work areas, burner or the and damage the surrounding edge of the combiset.
- Page 8 In the event of damage or defect, turn off the appliance immediately. Turn off the gas shut off valve and disconnect completely from the electrical supply. Contact the Miele Technical Service Department. Do not use the appliance until it has been repaired.
-
Page 9: Guide To The Combiset
Guide to the combiset a Fast burner Control knobs: b Normal burner f Rear burner c Burner grate g Front burner d Burner indicators e Display Indicators l On/Off indicator m "Residual Heat" Indicator... - Page 10 Guide to the combiset Burner n Burner cap o Burner head p Ignition safety control (Thermocouple) q Ignitor r Burner base...
-
Page 11: Before Using The Combiset
Before using the combiset Cleaning the combiset Metal components have a protective coating which may give off a slight odor Before using for the first time clean the the first time your new appliance is appliance as follows: heated. ^ Remove any protective foil. The harmless odor will dissipate after a ^ Wash the removable parts of the gas short time and does not indicate a... -
Page 12: Use
Fast-Ignition-System The knob must only be turned left to The gas combisets are equipped with a turn the appliance on and right to Fast-Ignition-System which turn it off. incorporates the following features: – The control knob does not need to If the knob is : be pressed until the flame lights. -
Page 13: On/Off Indicator And Residual Heat Indicator
Turning on Turning off ^ Turn the knob clockwise to "ß". This stops the flow of gas and turns off the combiset. On/Off indicator and Residual heat indicator ^ To turn on the burner, press the control knob down to pass the When the combiset is turned on, the resistance, then release the pressure On/Off indicator lights up. -
Page 14: Cookware
Cookware Pan size Suitable pans – Set the combiset to a high flame Any heat resistant pan can be used on when using a large diameter pan and a gas burner. low flame when using a small Unlike pans used on an electric diameter pan. -
Page 15: Safety Features
Safety features Ignition safety control Safety cut-off This appliance is equipped with an If a zone has been on for an unusually Ignition Safety Control. This control cuts long period of time (approx. 4 hours), it the gas supply if the flame goes out will automatically shut off. -
Page 16: Cleaning And Care
Keep the ignitor in the burner dry. If Apply sparingly with even pressure. it gets wet it will not spark. These cleaning products are available from Miele. Dry your combiset thoroughly after cleaning it to prevent lime deposits. Do not use stainless steel cleaner on... -
Page 17: Burners
Cleaning and care Burners Reassembling the burner The burner can be dismantled and cleaned when cool. ^ Remove the burner parts and wash them in a solution of warm water and liquid dish soap. Dry them thoroughly. Make sure that the flame holes are clean and completely dry. -
Page 18: Frequently Asked Questions
Frequently asked questions Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The burner does not ignite when the combiset is being used for the first time or after an extended period of not being used. - Page 19 Frequently asked questions The burner does not ignite after several attempts. Possible fault Solution Disconnect the appliance from the electrical supply for a few seconds. If the problem persists, check if: – The burner is assembled incorrectly. – Reassemble the burner as shown in "Cleaning and Care - Burners".
- Page 20 Frequently asked questions The igniter does not spark. Possible fault Solution The circuit breaker has tripped. Re-set the circuit breaker. Contact an electrician for assistance if in doubt. Food has deposited itself between the See "Cleaning and care". ignitor and the burner cap. Food has deposited on the ignition See "Cleaning and care".
-
Page 21: Technical Service
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. - Page 22 Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.
- Page 23 Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and appliance damage read these instructions before installation or use.
-
Page 24: Important Safety Instructions
(3.5 kPa). This appliance must be installation in these applications. Please isolated at test pressures equal to or contact the Miele Technical Service less than ½ psi (3.5 kPa). Department with specific requirements. The combiset must not be installed... - Page 25 IMPORTANT SAFETY INSTRUCTIONS Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it. See the installation instructions of the hood for these safety measurements. If the hood manufacturers instructions are not available or if flammable objects are installed over the combiset (e.g.
- Page 26 (50mm) 2" (50 mm) CS 1112 CS 1122 CS 1212 CS 1221 CS 1223 CS 1326 CS 1411 not recommended 6" (150 mm) CS 1312 CS 1322 CS 1421 10" (250 mm) CS 1011 CS 1012 CS 1028 not allowed...
-
Page 27: Installation
Installation Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2"... -
Page 28: Installation Dimensions
Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) e Gas fitting f Rating label... -
Page 29: Cut Out
Installation Cut out If during installation the seal around the frame does not sit flush with the ^ Make the countertop cut-out for the countertop in the corners, the corner desired number of appliances. radius, maximum " (4 mm), can be Remember to maintain a minimum carefully filed down to fit. -
Page 30: Installation Of Multiple Appliances
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out Countertop cut-out two appliances three appliances For the installation of three appliances For the installation of two appliances the width of the countertop cut-out D is the width of the countertop cut-out D is the sum of A and B and C. - Page 31 Installation Sample calculations for a countertop cut-out for three appliances appliance width appliance width appliance width Countertop minus 5/16" minus 5/16" cut-out (8 mm) (8 mm) 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11"...
- Page 32 Installation a Spring clips b Support bars c Space between support bar and countertop d Sealing strip The illustration represents the attachment of spring clips a and support bars b for 3 appliances. An additional support bar is required for each additional appliance. The position for attachment of an additional support bar depends on the width of appliance B.
-
Page 33: Attach The Spring Clips And Support Bars
Installation Attach the spring clips and support bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the "... - Page 34 Installation Granite countertop The screws are not needed for granite countertops. 3 / 1 6 " 1 " - 1 m m ) ( 2 5 - 3 0 ^ Coat the edges of the spring clips a, ^ and the space e between the support bars b and the countertop with silicone (supplied).
-
Page 35: Installing The Appliance / Appliances
Installation ^ Place the front edge of the next Installing the appliance / appliance into the cut-out. appliances ^ Connect the appliance / appliances ^ Feed the power cord down through to the main power supply (see the cut-out. "Electrical connection"). ^ Place the front edge of the appliance ^ Turn the appliance / appliances on into the cut-out. -
Page 36: Sealing
Installation Sealing Tiled surfaces The grouting a and shaded area under The appliance must not be permanently the appliance frame must be flat and sealed into the countertop when even so that the frame will lie evenly installed. The sealing strip under the and the sealing strip under the edge of edge of the appliance provides a the upper part of the appliance can... -
Page 37: Electrical Connection
Electrical connection This appliance must be grounded This appliance is equipped with a according to local or national codes. three-prong grounding plug to prevent shock hazards. It should be All electrical work should be plugged directly into a properly performed by a qualified electrician grounded outlet. - Page 38 Electrical connection Wiring Diagram...
-
Page 39: Gas Connection
Gas connection Installation and service must be The gas connection must be made performed by a qualified installer, in accordance with local codes or, in service agency or the gas supplier. the absence of local codes, with In Massachusetts a licensed the National Fuel Gas Code, plumber/gas fitter is required. -
Page 40: Gas Pressure Regulator
- 4" w.c. LP gas - 10" w.c. Do not use any regulator unless it has been supplied by Miele. Doing so may cause a gas leak. If there is any doubt concerning installation contact the Miele Technical Service Department. -
Page 41: Nominal Ratings
Gas connection Nominal ratings Maximum output Gas type BTU/hr Normal burner Natural Gas (NG) 5,700 1.65 Propane (LP) 5,000 1.45 Fast burner Natural Gas (NG) 10,600 3.10 Propane (LP) 9,300 2.75 Total output Natural Gas (NG) 16,300 4.75 Propane (LP) 14,300 Minimum output Gas type... -
Page 42: Converting To Another Type Of Gas
Converting to another type of gas The combiset should have been ordered for connection to either natural gas or LP gas (propane). If the combiset is not configured for the proper type of gas connection please contact your Miele Dealer. -
Page 43: Help Protect Our Environment
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling authority about the possibility of recycling these materials. - Page 44 Alteration rights reserved / 2409 M.-Nr. 07 366 180 / 02 For the most updated manual see the Miele web site.