Table of Contents
Advertisement
TNC COMMANDS LIST
The commands supported by the built-in TNC are listed below. You must enter a space between a command name (or short-form) and
a parameter, or between two parameters; ex. AU OFF, BEACON EVERY 18.
Command Name
8BITCONV
AFILTER
AUTOLF
AXDELAY
AXHANG
BEACON
BTEXT
CALIBRAT
CHECK
CONMODE
CONM
CONNECT
CONOK
CONO
CONSTAMP
CONS
CONV
CONVERSE
CPACTIME
CR
DAYSTAMP
DAYTIME
DAYUSA
DIGIPEAT
DISCONNE
Short
When ON, handles one character using 8 bits in Converse
8
mode. When OFF, handles one character using 7 bits.
Specifi es up to 4 control codes to be removed from received
AF
packets when in Converse mode.
When ON, sends a line feed (LF) to the computer after each
AU
carriage return (CR).
Specifi es the delay time to be added to TXDELAY between
AXD
PTT ON and start of transmission. The unit of the parameter
is 10 milliseconds.
Specifi es the voice repeater hang time. The unit of the
AXH
parameter is 100 milliseconds.
If set to EVERY, sends a beacon packet at intervals of the
specifi ed period (n). If set to AFTER, sends a beacon packet
B
only once after the specifi ed period (n). The unit of n is
10 seconds.
Specifi es the content of the data portion of a beacon packet.
BT
Sends a space/mark square wave (50/50 ratio). Enter Q to
CAL
exit Calibrate mode and restore the Command mode.
Specifi es the interval from signal drop-out until execution of
CH
disconnection. The unit of the parameter is 10 seconds.
With NOMODE set to OFF, causes the TNC to automatically
enter Converse or Transparent mode when connection is
completed.
Sends a connect request. Call1 is the callsign of the station
C
to be connected to. Call2 to call9 are callsigns of stations to
be digipeated through.
When ON, accepts a connect request and returns a UA
packet. When OFF, rejects a connect request and returns a
DM packet.
When ON, displays the current date and time when
connection is completed. The correct date and time must be
set using DAYTIME.
Causes the TNC to enter Converse mode. Press [Ctrl]+[C] to
or K
restore the Command mode.
When ON and in Converse mode, sends a packet at intervals
CP
of the period determined by PACTIME.
When ON, appends a carriage return (CR) to all packets to
CR
be sent.
When ON, pressing [Ctrl]+[T] in Converse mode causes the
DAYS
TNC to send date data in addition to time data.
Sets the current date and time. Enter YYMMDDhhmmss.
DA
Sets 00 as the second if entry of the second is omitted.
When ON, displays the date like MM/DD/YY. When OFF,
DAYU
displays the date like DD-MM-YY.
DIG
When ON, allows the TNC to function as a digipeater.
D
Sends a disconnect request.
Description
PACKET-3
Parameter
Default
ON/ OFF
ON
$00 ~ $80
$00
ON/ OFF
ON
0 ~ 120
0 ~ 250
EVERY/ AFTER n
EVERY 0
(n = 0 ~ 250)
0 ~ 159 characters
−
0 ~ 250
C/ T
Call1 (VIA call2,
call3, ... call9)
ON/ OFF
ON
ON/ OFF
OFF
−
ON/ OFF
OFF
ON/ OFF
ON
ON/ OFF
OFF
−
ON/ OFF
ON
ON/ OFF
ON
−
0
0
−
−
30
C
−
−
−
−
Advertisement
Table of Contents
