Advertisement
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is working normally.
If the Power LED is not lit, please check as follows:
A1:
Make sure the power adapter is connected to the switch with power
source properly.
A2:
Make sure the voltage of the power supply meets the requirements of
the input voltage of the switch.
A3:
Make sure the power source is ON.
Q2. The Link/Act LED is not lit when a device is connected
to the corresponding port.
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are firmly plugged into the
switch and the device.
A2:
Make sure the connected device is turned on and works normally.
A3:
The cable must be less than 100 meters long (328 feet).
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
Explanation of the symbols on the product label
DC voltage
Indoor use only
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU
in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment.
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
限用物質含有情況標示聲明書
限用物質及其化學符號
產品元件名稱
鉛
鎘
汞
六價鉻
Pb
Cd
Hg
CrVI
PCB
外殼
電源適配器
備考1. " "系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2. " "系指該項限用物質為排除項目。
多溴聯苯
多溴二苯醚
PBB
PBDE
Specifications
General Specifications
Standard
IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.1p
Protocol
CSMA/CD
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Data Transfer Rate
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
10Base-T:
UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX:
UTP category 5, 5e cable (maximum 100m)
Network Media (Cable)
EIA/TIA-568 100Ω STP (maximum 100m)
1000Base-T:
UTP category 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
Interface
5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports
LED Indicators
Power, 10/100M LED, 1000M LED
Advanced Features
IGMP Snooping, QoS (802.1p/DSCP Priority)
Transfer Method
Store-and-Forward
MAC Address Learning
Automatically learning, automatically aging
10Base-T: 14881pps/Port
Frame Forward Rate
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
Environmental and Physical Specifications
Operating Temperature
0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature
-40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity
10% to 90%RH non-condensing
Storage Humidity
5% to 95%RH non-condensing
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Use only power supplies which are provided by manufacturer
and in the origin packing of this product.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of
directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning
This is a class B product. In a domestic
environment, this product may cause
radio interference, in which case the user
may be required to take adequate
measures.
Advertisement
