Specifications - Makita DPO600 Instruction Manual

SPECIFICATIONS

Model:
Backing pad diameter
Orbits per minute
Overall length
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Symbols
The followings show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Only for EU countries
Ni-MH
Li-ion Do not dispose of electric equipment or
battery pack together with household waste
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries and Accumulators
and Waste Batteries and Accumulators
and their implementation in accordance
with national laws, electric equipment and
batteries and battery pack(s) that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for polishing.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-4:
Model DPO500
Sound pressure level (L
Sound power level (L ) : 93 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DPO600
Sound pressure level (L
Sound power level (L ) : 94 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Normal mode
Finishing mode
) : 82 dB(A)
pA
) : 83 dB(A)
pA
DPO500
123 mm
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-4:
Model DPO500
Work mode: polishing
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DPO600
Work mode: polishing
Vibration emission (a
Uncertainty (K) : 1.5 m/s
2 ENGLISH
DPO600
148 mm
-1
0 - 6,800 min
-1
0 - 5,200 min
530 mm
D.C. 18 V
3.1 - 3.6 kg
2
) : 9.5 m/s
h, P
2
2
) : 10.0 m/s
h, P
2