Getting Started Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. NOTE Battery Installation Your UH515SX-2NB/UH515DLX-2 unit uses the included NiMH battery pack for power. The unit can be powered with optional 3 AAA ALKALINE batteries*.
Page 4
Plug the AC adaptor into the rear of the charge cradle and into the mains power. Place the UH515SX-2NB/UH515DLX-2 into the charge cradle. The charge light will come on to indicate the unit is charging. Before operating the UH515SX-2NB/UH515DLX-2, charge the battery pack for 16 hours.
To remove the belt clip, slightly lift the belt clip locker and slide the belt clip at the same time until released. Using the Carabiner Clip Use the carabiner clip to conveniently secure the UH515SX-2NB/UH515DLX-2 to a belt or strap. Low Battery Alert If the battery level becomes low, the battery indicator icon on the display begins flashing.
1.5 secs until it beeps to activate Key Lock. The appears. To unlock the keypad, press and hold (hi/lo/lock) again for 1.5 Secs. The disappears. While in Keylock on mode, the UH515SX-2NB/UH515DLX-2 can still receive and transmit. NOTE UNIDEN UH515SX-2NB/UH515DLX-2...
(Channels 22 and 23 are for telemetry and telecommand applications, channels 61,62 and 63 are for future use. TX is inhibited on these channels.) menu The maximum RF transmit power of UH515SX-2NB/UH515DLX-2 is 1.5W. hi/lo lock Before you transmit, listen for activity on the selected channel.
To return to normal receive mode press and hold (CALL/MON) Scanning The UH515SX-2NB/UH515DLX-2 has two types of scanning; Open Scanning (OS) and Group Scanning (GS), OS Scan searches all the channels and frequencies in its memory continuously. GS Scan is similar to OS scan but has the added ability to monitor the priority channel every 1.5 seconds.
Page 9
To deactivate GS scanning, press (PTT) or press and hold vol (scan). 1. If SCAN is deactivated while it is tuned to an active channel, the UH515SX-2NB/UH515DLX-2 will stay on that active channel. If none of the channels re-active, the radio will reinstate the Scan start channel.
CTCSS is a feature that allows a group to talk to each other without hearing other users on the same channel. Select desired channel. Press (menu) once. CTCSS setting flashes. Press (ch) or (vol) to change the selection. Press & hold (menu) to save and exit. UNIDEN UH515SX-2NB/UH515DLX-2 UHF CB Radio...
CTCSS or DCS code. Press (menu) five times. BCL setting flashes. Press (ch) or (vol) change the setting on or off. Press & hold (menu) to save and exit. UNIDEN UH515SX-2NB/UH515DLX-2 UHF CB Radio...
Operation Call Tone Your UH515SX-2NB/UH515DLX-2 radio is equipped with 5 selectable call tones that will be transmitted when CALL/MON is pressed. Press (menu) six times. CL setting flashes. Press (ch) or (vol) change the selection. The 5 call tones are CL 1 to CL 5.
Page 13
The above situations are not a fault of the radio but a symptom of mixed wideband and narrowband radios in current use. It is expected that as older wideband radios are phased out this issue will be eliminated. UNIDEN UH515SX-2NB/UH515DLX-2 UHF CB Radio...
IMPORTANT: Satisfactory evidence of the original purchase is required for warranty service Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Page 15
Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden at the addresses shown below. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim.