Advertisement
Quick Links
Direct Drive Bicycle Trainer
Instructions Manual
Merit of Direct Drive
Compatibility
Contact
MINOURA North American Tech Center
(for U.S. residents ONLY)
Hayward, California, U.S.A.
Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST)
Fax:
1-510-538-5899
Email:
support@minourausa.com
(Sprocket gear is sold separately)
LSD9200 "Kagura" Direct-Drive works with your current bike frame when you remove your
wheel and mount your frame directly to the unit. Direct-Drive eliminates any potential power loss
from traditional trainers because there is no chance of tire slippage and it transmits all the power
you generate to the electric motor.
The precisely tuned resistance unit eliminates all the noise and vibrations usually associated with
indoor trainers and provides a very smooth and quiet training session anytime.
Kagura-DD is compatible with Shimano and SRAM 8s, 9s, 10s and 11s. Campagnolo is currently
NOT supported. You need to prepare the rear sprocket gear that fits your bike component
separately.
The AC Adapter is capable with worldwide voltage 100V – 240V, but the electric plug design
must fit your country's regulation. If you need to change the plug that came with your trainer, it
is available as an option for purchase.
If you have any trouble with this product or request for maintenance, refer the attached "Minoura
Limimted Warranty Policy" card first, then contact the shop you originally purchased this
product or the distributor in your country. The distributor list is found on our web site.
We strongly recommend visiting the
Minoura website regularly to check for
updates to the Kagura firmware.
For more info, check out ...
http://www.minoura.jp/english/trainer/smartturbo/
lsd9200.html
and click "Firmware Updates" button.
MINOURA Japan Headquraters
(for ALL customers)
134-1 Shimomiya, God, Anpachi, Gifu 503-2312 Japan
Fax:
+81-584-27-7505
Email:
minoura@minoura.jp
Web:
www.minoura.jp
(ver.1.0 2019/2)
Made in Japan
Advertisement
Related Manuals for MINOURA SmartTurbo Kagura EHT1020
Summary of Contents for MINOURA SmartTurbo Kagura EHT1020
- Page 1 If you need to change the plug that came with your trainer, it is available as an option for purchase. If you have any trouble with this product or request for maintenance, refer the attached "Minoura Contact Limimted Warranty Policy"...
-
Page 2: Important Notes
Do not try to disassemble the unit to repair without prior approval from Minoura. • Any warranty will be void if you use Kagura-DD for any other purpose than instructed. Minoura offers 1-year limited warranty on this product from the date of your purchase for any problem caused by manufacturer's defect. - Page 3 LSD9200 Contents Flywheel Drive Belt [LSD9200 Main Body] [Step-Bar] Step-Bar Body Foot Adjuster Carrying Handle Power Cable (shown is A-type plug) [Electric Power Supply] Power Plug AC Adapter Foot Adjuster (100V – 240V) [Supplied Parts] Spacer Ring for 10s (*1) Quick Release Skewer Knob Bolt (Large) Leftside End Plug...
- Page 4 How To Install Step-Bar Required Tool : Nothing Step-Bar (direction is specified) Knob Bolt (Large) M8 Flat Washer Round Collar Round Collar Knob Bolt (Small) M6 Flat Washer (Fig. A) Install the Step-Bar to the Body. (Fig. A) Put the Knob Bolt (Large) with the Round Collar into the plain hole on the Step-Bar, and screw it into the thread hole on the Body.
- Page 5 Turn the Step-Bar 90 degrees, set it on the grooves on the bracket, and tighten the larger Knob Bolt to hold. (Fig. D) The smaller Knob Bolt can be stored in the thread hole on the Step-Bar. Now the Kagura-DD is ready to be stored in the narrow area such as under the bed.
- Page 6 How To Replace To 12mm Thru Axle The original hub on your Kagura-DD is preset for the standard 9mm Q/R. If your bike is equipped with 12mm thru axle system, you must replace the right side hub end with the supplied special plug.
- Page 7 How To Remove Sprocket Gear To remove the sprocket gear, you need a special tool called a Sprocket Remover together with the Lock Ring Tool. Sprocket Remover Set the chain of the Sprocket Remover to the largest gear on the sprocket. It means that turning the Lock Ring counter- clockwise will move the sprocket gear together in the same direction, so you need to hold it by this tool.
- Page 8 How To Mount a Bike on Your Kagura-DD Fully open the Quick Release Skewer lever. In order to make mounting the bike easier, set the rear derailleur to the top. As same as installing the rear wheel onto the bike, hook the chain on the top gear, then set the bike frame on Kagura-DD gently.
- Page 9 12mm Thru Axle System About The Direction of The Leftside End Plug Compatible with the rear end width in 142mm and 148mm only. 142mm Change the direction of the Leftside End Plug to the hub as shown in 148mm Fig. Q. 142mm : Face the wider sleeve side inward.
- Page 10 (Blue LED is still blinking. Optional ANT+ reciever is required for this connection. Refer the application screen about the connecting status.) Minoura does not supply instructions on how to connect or pair your trainer with your chosen training app. Please refer to the app for instructions on how to connect the trainer for use with any given app.
- Page 11 The first step in trouble shooting your unit is to make sure you are using the most current version of our firmware. Update your firmware by going to the link posted above. To get this service, you must be registered to Minoura as an official user. How To Adjust Belt Tension...
- Page 12 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.