Advertisement
Quick Links
Indoor Bike Trainer
"VFS3R"
Instructions Manual
Important Notice – About Our Service Policy
Minoura is offering 1-year limited warranty on the resistance unit and 5-year limited
warranty on the frame from the date of your purchase.
This warranty service is valid only for the original user who purchased the product in brand-
new condition at a bike shop. Any product purchased through unauthorized mail order house,
auction and personal trading void this warranty service.
If you have questions regarding the product or request to get the replacement parts within
these terms, please contact the shop where you purchased this product or the distributor in
your country first. Only when not available, you can contact the following service points;
MINOURA NORTH AMERICA
(valid for U.S. residents only)
1996 East Ave, Hayward, CA 94541-5454 U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
MINOURA JAPAN HEADQUARTERS
(for all customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp / URL: www.minoura.jp
MADE IN JAPAN
Advertisement
Related Manuals for MINOURA VFS3R
Summary of Contents for MINOURA VFS3R
- Page 1 Instructions Manual Important Notice – About Our Service Policy Minoura is offering 1-year limited warranty on the resistance unit and 5-year limited warranty on the frame from the date of your purchase. This warranty service is valid only for the original user who purchased the product in brand- new condition at a bike shop.
-
Page 2: Parts List
Parts List V3-13 V3-4 V3-12 HF-4 HF-4 V3-8 V3-7 V3-3 F-1: Coupling Tube (Right) F-2: Coupling Tube (Left) F-4: Coupling Cover F-7: Hub Handle V3-6 F-8: Hub Knob Bolt V3-5 F-9: Coupling Protector HF-4: 35mm Rubber Foot Cap V3-2 V3-11 HM-13: Base Plate M8-2: Main Frame... -
Page 3: Important Notes
IMPORTANT NOTES • Read all instructions carefully before use. • Keep the manual handy at all times. • Some assembly required. Use correct tools for your safety. • Do NOT use trainer for any other purpose than instructed. • The trainer is manufactured to precise standards. Disassembling or rebuilding by yourself will void the warranty. - Page 4 How To Setup Your VFS3R Trainer <Required Tools> • Hex Wrench: M4 / M5 • Spanner: 10mm Open the frame support legs and fit the rubber feet at the correct angle and depth so the base is in full contact with the floor.
- Page 5 Connecting the Front Fork Support to the Main Frame. Loosen the Knob Bolt then slide the Extension Tune into the Center Frame. Tighten the Knob Bolt temporally, you will adjust the position later. NOTE: If you had removed the Extension Joint completely, insert it to the Center Frame while making sure the inside hole is aligned to the Joint's hole.
- Page 6 How To Install Your Bike On Trainer Open both couplings by turning the left side knob (Fig.F) and the right side hub handle (Fig. G) anti-clockwise. Do NOT overloosen the couplings, otherwise the knob or hub handle may become unthreaded inside the frame. (Fig.
- Page 7 Apply the VFS resistance unit to the tire by lifting up it temporally by hand to know the wheel position. If the tire touches either left or right side plastic housing of the VFS unit (see Fig. K), you must adjust the wheel position again by operating both the left knob and the right hub handle.
- Page 8 How To Install The Remote Lever You can install the remote lever on anywhere the diameter is between 22.2mm (7/8”) and 31.8mm (1-1/4”) like as on the handlebar. Fully loosen the knob bolt on the plastic holder until it stops then push down the bolt to open the holder. (Fig. O) Place the holder onto the handlebar, shut the holder, and pull up the bolt then tighten it.
- Page 9 <Required Tools> • M5 hex wrench Using The Small Wheel Adapter • 10mm open spanner) If you wish to use any smaller wheel sized between 24 x 1.0" and 26 x 1.75" on the trainer, install the supplied Z-shaped Adapter under the VFS unit. (Fig. S) Adapter 10mm Open Spanner Base Plate...