Related Manuals for Hinkley MERRICK 60
Summary of Contents for Hinkley MERRICK 60
- Page 1 60" MERRICK ™ INDOOR / OUTDOOR LED FAN DC MOTOR CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
HANGING THE FAN TROUBLESHOOTING ELECTRICAL CONNECTIONS ENERGY GUIDE FINISHING THE INSTALLATION SPECIFICATIONS INSTALLING THE BLADES SMART BY BOND WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2021 Hinkley Lighting, Inc. | hinkley.com |... - Page 4 If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. | hinkley.com...
-
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
Blade to Motor Screws MH900360Fxx w/Fiber Washers, Balance Kit, Safety cable hardware NOTE: Design of parts shown above may look slightly di erent for (wood screw, flat washer) your specific model of fan. XX=FAN FINISH | hinkley.com... -
Page 7: Preparation
The outlet box must be able to support a minimum of 35 pounds. Flat washer Attach hanging bracket to outlet box using screws provided Spring washer with the outlet box. Outlet box screw Fig. 1 ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 8: Hanging The Fan
Tighten security set screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod. Downrod Tighten nuts against mounting collar. Security Screws Mounting Collar Downrod Pin Cotter Pin Top of Fan Body Fig. 2 | hinkley.com... - Page 9 Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly Safety cable loop tighten screw in the clamp. Cut off excess cable. Wood screw and washer Safety cable Fig. 4 ©2021 Hinkley Lighting, Inc. | hinkley.com...
-
Page 10: Electrical Connections
Connect the WHITE receiver neutral wire to the WHITE building GRAY neutral wire. Connect the COPPER building ground wire to the 4 YELLOW/ GREEN ground wires from the fan and receiver. Hanger bracket Fig. 2 Receiver Fig. 1 hinkley.com... -
Page 11: Finishing The Installation
Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before attaching the canopy to the bracket by turning the housing until it drops into place. ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 12: Installing The Blades
Secure by tightening the 2 screws previously loosened and the one previously removed. Light Wires Mounting Hub (bottom of motor) Adapter plate A Screws Fig. 1 | hinkley.com... -
Page 13: Installing The Led Assembly And Glass Shade
Wire connectors Raise the glass shade against the LED assembly and turn clockwise until snug, DO NOT OVERTIGHTEN. Restore power and your LED assembly is ready for operation. assembly Screws Glass shade Fig. 2 ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 14: Installing The Fan Without The Light Kit (Optional)
Place the key holes on the adapter plate B over the 2 screws previously loosened, turn the adapter plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. | hinkley.com... -
Page 15: Installing The Wall Control
Remote transmitter will be held in place with built in magnets. Cradle B Wall plate Plastic Face plate anchor Transmitter Outlet box Wall plate Cradle A Face plate Transmitter Wall Fig. 1 HIRO Control System Fig. 2 ©2021 Hinkley Lighting, Inc. | hinkley.com |... - Page 16 Power lead to the fan is connected to the remaining switch lead. (Fig. 4) Attach the cradle A to the wall switch box using the supplied hardware. Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora face plate.
-
Page 17: Operation
NOTE: A single fan can be controlled with as many as 3 wall controls in one room. Every control will need to repeat the pairing process based on instructions above and all controls must be within 30 feet of the fan. ©2021 Hinkley Lighting, Inc. | hinkley.com |... - Page 18 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 | hinkley.com...
-
Page 19: Care And Cleaning
2. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation. 3. Check to assure all dowrods to motor hardware and/or hanger ball are tight. 4. Make sure ceiling box is secure. ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 20: Energy Guide
• Your cost depends on rates and use • Energy Use: 17 Watts RPMs All estimates based on typical use, excluding lights ftc.gov/energy Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod | hinkley.com... -
Page 21: Smart By Bond
Wait 10 seconds. f) Hold down the Power button on the transmitter you wish to pair. In addition to the included wall control, you can control your Hinkley The fan light should flash three times and the motor spin up for fan through the Bond app. - Page 22 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 23 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...