Using The Blender; Cleaning And Maintenance - Vitek VT-1459 Manual Instruction

ENGLISH
• Unpack the unit completely and remove any
advertising stickers preventing the unit op-
eration.
• Check the unit for damages, do not use it in
case of any.
• Before switching the unit on, make sure that
the mains voltage corresponds to the unit op-
erating voltage.
• The unit is intended for operation with AC sys-
tem and 50 or 60 Hz frequency, the unit does
not need any additional settings for operating
with the required nominal frequency.
• Before the first use wash all the removable
parts (1, 2, 3, 5, 6) with warm water and neu-
tral detergent and then dry thoroughly.
• Clean the motor unit (7) with a soft, slightly
damp cloth and then wipe it dry.
• Do not immerse the motor unit (7) into any
liquids and do not wash it with water.
• Place the blender on a flat stable surface.
ATTENTION! Continuous operation time of
the blender should not exceed 60 seconds,
and the break between operations should be
1-2 minutes.
• Do not remove the blender bowl (3) and the
bowl lid (2) during the operation.

USING THE BLENDER

The blender is used for chopping products, ice,
mixing various ingredients and making cocktails.
• Install the blender bowl (3) on the motor unit
(7), the bowl (3) handle (4) must be situated
on the right or left side of the motor unit (7),
turn the bowl (3) clockwise until bumping.
• Remove the blender bowl lid (2).
• Put the necessary ingredients into the bowl (3).
• Cover the blender bowl (3) with the lid (2),
insert the measuring cup (1) into the lid (2)
opening and turn it clockwise until bumping.
• Make sure once again that the blender bowl
(3) is installed correctly.
• Insert the power plug into the mains socket.
Note: The blender will not be switched on if the
blender bowl (3) is installed incorrectly.
• Use the operation mode switch (8) to set the
required rotation speed of the knives:
«1» (low speed) – for mixing of liquid prod-
ucts;
«2» (high speed) – for liquid and hard prod-
ucts;
«P» – pulse mode.
• To switch the pulse mode on, set the switch
(8) to the position «P» and hold it.
• During the operation or between the opera-
tion cycles, you can add the required ingredi-
ents into the bowl (3). To do this, remove the
measuring cup (1) turning it counterclockwise,
you can use the measuring cup (1) as a bowl
for adding necessary liquid ingredients. After
adding the ingredients, place the cup (1) back
to its place and turn it clockwise until bumping.
• After the unit's operation is finished, set the
operation mode switch (8) to the «0» position
and unplug the unit.
• Remove the blender bowl (3) from the motor
unit (7) by turning it counterclockwise until
bumping.
• Remove the lid (2) from the bowl (3) and take
the processed products out of the bowl (3).
• After the operation is finished, wash the
blender bowl (3).
Note: If food processing is hindered, add some liq-
uid (water, liquor, juice) into the blender bowl (3).
• Before starting to chop/mix, we recommend
to peel fruit, remove inedible parts, such as
stones, and cut fruit into 2х2 cm cubes.
ATTENTION! Continuous operation time of
the blender should not exceed 60 seconds,
and the break between operations should be
1-2 minutes.

CLEANING AND MAINTENANCE

After the unit operation is finished, switch the
blender off by setting the operation mode switch
(8) to the «0» position and unplug it.
• Remove the blender bowl (3) from the motor
unit (7) by turning it counterclockwise until
bumping.
• Remove the lid (2) and take the processed
products out of the bowl (3).
• Wash the bowl (3) preliminarily.
• Remove the knife block (6) and the sealing
gasket (5). To remove the knife block (6) turn
it counterclockwise and remove.
WARNING: The knife block (6) cutting edges
are very sharp and dangerous. Handle the
knife block very carefully.
• Wash the knife block (6) only from the knives
side, do not immerse the knife block (6) into
water or other liquids.
• Wash the bowl (3), the sealing gasket (5), the
lid (2) and the measuring cup (1) with warm
water and soft detergent and dry them.
• You can wash the blender bowl (3) in a dish-
washing machine after removing the knife
block (6).
4