Asus RS720A-E9-RS12V2 User Manual page 23

Action PHASE
PSP Boot Loader
PSP Boot phase (Status Post
Codes)
ASUS RS720A-E9-RS12V2
POST CODE TYPE
0xA0 Progress
0xA1 Progress
0xA2 Progress
0xA3 Progress
0xA4 Progress
0xA5 Progress
0xA6 Progress
0xA7 Progress
0xA8 Progress
0xA9 Progress
0xAA Progress
0xAB Progress
0xAC Progress
0xAD Progress
0xAE Progress
0xAF Progress
0xB0 Progress
0xB1 Progress
0xB2 Progress
0xB3 Progress
0xB4 Progress
0xB5 Progress
0xB6 Progress
0xB7 Progress
0xB8 Progress
0xB9 Progress
0xBA Progress
0xBB Progress
0xBC Progress
0xBD Progress
0xBE Progress
0xBF Progress
0xC0 Progress
0xC1 Progress
0xC2 Progress
0xC3 Progress
0xC4 Progress
0xC5 Progress
0xC6 Progress
0xC7 Progress
0xC8 Progress
0xC9 Progress
0xCA Progress
0xCB Progress
0xCC Progress
0xCD Progress
0xCE Progress
0xCF Progress
0xD0 Progress
0xD1 Progress
0xD2 Progress
0xD3 Progress
0xD4 Progress
0xD5 Progress
0xD6 Progress
0xD7 Progress
0xD8 Progress
0xD9 Progress
(continued on the next page)
DESCRIPTION
Bootloader successfully entered C Main
Master initialized C2P / slave waited for master to init C2P
HMAC key successfully derived
Master got Boot Mode and sent boot mode to all slaves
SpiRom successfully initialized
BIOS Directory successfully read from SPI to SRAM
Early unlock check
Inline Aes key successfully derived
Inline-AES key programming is done
Inline-AES key wrapper derivation is done
Bootloader successfully loaded HW IP configuration values
Bootloader successfully programmed MBAT table
Bootloader successfully loaded SMU FW
PSP and SMU configured WAFL
User mode test harness completed successfully
Bootloader loaded Agesa0 from SpiRom
AGESA phase has completed
RunPostDramTrainingTests() completed successfully
SMU FW Successfully loaded to SMU Secure DRAM
Sent all required boot time messages to SMU
Validated and ran Security Gasket binary
UMC Keys generated and programmed
Inline AES key wrapper stored in DRAM
Completed FW Validation step
Completed FW Validation step
BIOS copy from SPI to DRAM complete
Completed FW Validation step
BIOS load process fully complete
Bootloader successfully release x86
Early Secure Debug completed
GetFWVersion command received from BIOS is completed
SMIInfo command received from BIOS is completed
Successfully entered WarmBootResume()
Successfully copied SecureOS image to SRAM
Successfully copied trustlets to PSP Secure Memory
About to jump to Secure OS (SBL about to copy and jump)
Successfully restored CCP and UMC state on S3 resume
PSP SRAM HMAC validated by Mini BL
About to jump to <t-base in Mini BL
VMG ECDH unit test started
VMG ECDH unit test passed
VMG ECC CDH primitive unit test started
VMG ECC CDH primitive unit test passed
VMG SP800-108 KDF-CTR HMAC unit test started
VMG SP800-108 KDF-CTR HMAC unit test passed
VMG LAUNCH_* test started
VMG LAUNCH_* test passed
MP1 has been taken out of reset
PSP and SMU Reserved Addresses correct
Reached Naples steady-state WFI loop
Knoll device successfully initialized
32-byte RandOut successfully returned from Knoll
32-byte MAC successfully received from Knoll.
Knoll device verified successfully
Done enabling power for Knoll
Enter recovery mode due to trustlet validation fail.
Enter recovery mode due to OS validation fail.
Enter recovery mode due to OEM public key not found.
1-13