Advertisement
Quick Links
Installation Manual
Land Rover LR3 2005-2009
Interface with HDMI Mirroring
Part #: NAVTOOL6.0-LG2-RR
NOTICE: Navtool recommends having this installation performed by a certified technician.
Logos and trademarks used here in are the properties of their respective owners.
1
Land Rover LR3 2005-2009
Advertisement
Related Manuals for NavTool LR3
Summary of Contents for NavTool LR3
- Page 1 Installation Manual Land Rover LR3 2005-2009 Interface with HDMI Mirroring Part #: NAVTOOL6.0-LG2-RR NOTICE: Navtool recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Land Rover LR3 2005-2009...
- Page 2 Print End Pages 1-4 and give them to the customer Open the camera app on your smart- phone and point your rear camera at the QR-Code to scan it. Finally, tap the pop up banner to open support website. Land Rover LR3 2005-2009...
- Page 3 • Using protective blankets to cover front seats, interior of the vehicle and center console. • Always install a fuse 6-12 inches away from NavTool interface, 5 amp fuse should be used. • Always secure NavTool interface with Velcro or double side tape to prevent rattling of the interface.
- Page 4 What’s In The Box? USB Configuration Cable NavTool Interface NavTool LVDS Cables (Part # NT-USB-CNG) (Part # NAVTOOL6.0-LG2) (Part # NT-RR-LVDS) NavTool Vehicle Specific NavTool Interface Harness Plug and Play Harness (Part # NT-WHNT6) (Part # NT-RRSPL) Land Rover LR3 2005-2009...
- Page 5 USB Port for Apple CarPlay and Android Auto- Not Used HDMI Port- HDMI port is dedicated for connecting video sources such as iPhone mirroring, Android Mirroring, Apple TV, Roku, FireStick, Chromecast, PlayStation, Xbox, or similar devices. Land Rover LR3 2005-2009...
- Page 6 In that case, this wire must be connected to the vehicle’s reverse +12V output. (Change setting “Manual Activation Wire as +12V Reverse Input” See page 41) +12V Output- 500 mA output can be used to drive a relay. This output provides +12V at all times when the vehicle is running. Land Rover LR3 2005-2009...
- Page 7 Switch 2 Set to ON - ON is Down AUX Input depends on the type of jack installed in your car from the factory Back of Navigation Click Click Click Factory Wire Click NavTool Supplied Cable (Part # NT-RRSPL) Land Rover LR3 2005-2009...
- Page 8 Switch 2 Set to ON - ON is Down Factory LVDS Cable *2- Cable that previously used to be connected to blue connector in the back of the navigation Click Close Up View of Radio Connectors Back of Car Navigation Land Rover LR3 2005-2009...
- Page 9 Mac computers must use the latest version of the Google Chrome browser. Google computers must use the latest version of the Google Chrome browser. TO CONFIGURE THE INTERFACE, GO TO HTTPS://CONFIG.NAVTOOL.COM Connect the interface to the computer using supplied USB Configuration Cable (Part # NT-USB-CNG)
- Page 10 Installation Instructions STEP 2 Continued Navigation is located behind the cover of the left cargo area. Land Rover: Range Rover 2005-2009 Land Rover: Range Rover Evoque 2005-2009 Land Rover LR3 2005-2009...
- Page 11 Installation Instructions STEP 2 Continued Navigation is located under driver seat. Land Rover: Range Rover Sport 2005-2009 Land Rover: LR3 2005-2009 Land Rover LR3 2005-2009...
- Page 12 Reconnect previously removed radio connectors into the back of the radio. STEP 4 Connect supplied universal wiring harness (Part # NT-WHNT6) into plug and play harness (Part # NT-RRSPL). (Part # NT-RRSPL) (Part # NT-WHNT6) (For complete image, see Quick Connection Guide on page 7) Land Rover LR3 2005-2009...
- Page 13 Installation Instructions STEP 5 Step 1: Connect the AUX plugs on NavTool Supplied Cable (Part # NT-RRSPL) to AUX cables and plug them into the AUX input of your car. NavTool Supplied Harness (Part # NT-WHNT6) AUX Input depends on the type of jack...
- Page 14 Factory LVDS Cable STEP 7 Step 1: Connect NavTool supplied LVDS cable into the blue port on the back of the navigation. Step 2: Connect NavTool supplied LVDS cable into the brown port shown in the image below. NavTool Interface...
- Page 15 • If you are adding side or front cameras, install them and plug them into the appropriate camera RCAs. • If you are installing any HDMI or streaming devices, connect it to the HDMI port of the NavTool. Land Rover LR3 2005-2009...
- Page 16 Installation Instructions STEP 9 Plug the AUX plug you connected to the harness into the AUX input of the car. See picture below. Land Rover LR3 2005-2009...
- Page 17 Testing and Settings STEP 1 • Start the car, observe NavTool LED lights should be one blinking blue and two steady lit green LED lights. HDMI LED Data LED Power LED • At this time, your car radio should boot up into its initial state, and the radio should be working.
- Page 18 Testing and Settings STEP 3 • Tap the Navigation button to activate NavTool interface. (see Fig. 1). You should hear a chirp, and after that, the interface will start, and the NavTool menu will appear on the screen. After activating the interface, the NavTool screen will show (see Fig.2)
- Page 19 Set vehicle in reverse gear to test the operation of the factory rear view camera. Press and hold one of the four corners of the touch screen for 3 seconds to turn OFF the NavTool inter- face. Press and hold the corner of the touch screen for a few seconds until the bottom menu appears on the screen, release the finger and hold the corner of the screen again to return to the factory menu.
- Page 20 • To exit HDMI input or any Camera inputs, tap the touch screen to bring up the bottom menu. After everything is tested and working, reassemble the vehicle. Land Rover LR3 2005-2009...
- Page 21 If all steps above are checked off, you will save time, money and have an extremely happy customer. All above steps eliminate any unnecessary customer comebacks to your shop. If you require any further assistance please call our tech support line, email or go online WWW.NAVTOOL.COM 1-877-628-8665 techsupport@navtool.com Land Rover LR3 2005-2009...
- Page 22 Interface Menus and Settings NavTool Interface Screen Press the Navigation button on the screen to activate NavTool interface. Press and hold one of the four corners of the touch screen to deactivate NavTool interface. After you activated the interface, you will be brought to this screen that you can navigate using the factory touch screen.
- Page 23 Apple CarPlay/Android Auto screen. Apple CarPlay/Android Auto Module Not Installed You will get this message when selecting this option on the NavTool interface that is not equipped with Apple CarPlay/ Android Auto module. HDMI Tap the HDMI button to enter this option.
- Page 24 (Note: This input will not display factory installed right lane watch camera) To exit Right Lane Watch Camera, tap the touch screen to bring up the bottom menu. Land Rover LR3 2005-2009...
- Page 25 You can lower the contrast of the interface by tapping the minus on the left and increase the interface’s contrast by tapping the plus on the right. Save or cancel any changes you have made. Land Rover LR3 2005-2009...
- Page 26 Parking lines: Select this option if you are installing an aftermarket right lane watch camera and you wish to add distance lines to the camera image. Land Rover LR3 2005-2009...
- Page 27 Down check to save your changes. X to cancel your changes. You can move your parking lines down by selecting the down arrow for your selected parking line. Land Rover LR3 2005-2009...
- Page 28 Set this feature to ON if you want to directly enter into the Apple CarPlay/Android Auto mode when activating the interface, Set this feature to OFF if you want to enter NavTool menu upon and bypasing the NavTool menu. Do not select this mode if you activation of the interface.
- Page 29 How to Connect Rear Screens to Car With AV Input Examples of equiptment used if connecting or installing additional rear screens Car Monitor NavTool Interface HDMI to AV Adaptor 1 in 2 Out HDMI Splitter HDMI Sources Land Rover LR3 2005-2009...
- Page 30 How to Connect Rear Screens to Car With HDMI Input Examples of equiptment used if connecting or installing additional rear screens Car Monitor NavTool Interface Car HDMI Input 1 in 2 Out HDMI Splitter HDMI Sources Land Rover LR3 2005-2009...
- Page 31 FM, or XM, if equipped, Disc, or AUX (Auxiliary). Must set a radio to auxiliary/AUX before activating NavTool to hear audio from car speakers. • Audio will not play through car speakers if AUX is not connected or radio is not set to AUX input.
- Page 32 NavTool Apple CarPlay/Android Auto interface will play via AUX input of the radio. See Page 1 for details. • Press the Navigation button on screen to activate NavTool interface. (see Fig.1) You should hear a chirp, and after that, the interface will start, and the NavTool menu will appear on the screen.
- Page 33 Set this feature to ON if you want to directly enter into the Apple CarPlay/Android Auto mode when activating the interface, Set this feature to OFF if you want to enter NavTool menu upon and bypasing the NavTool menu. Do not select this mode if you activation of the interface.
- Page 34 You can lower the brightness of the interface by tap- ping the minus on the left and increase the interface’s brightness by tapping the plus on the right. Save or cancel any changes you have made. Land Rover LR3 2005-2009...