Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside.
Additional Features Supports @BIOS Supports EasyTune Overclocking Over voltage (AGP/DDR) by BIOS Over clock (CPU/DDR) by BIOS Form Factor Micro ATX size form factor, 24.4cm x 23.3cm 8VM800M-RZ Motherboard Layout KB_MS ATX_12V AUDIO BIOS F_AUDIO VT6103L CD_IN CODEC COMB GAME 8VM800M-RZ Motherboard 24.4 cm...
Chipset that supports HT Technology ® - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology 8VM800M-RZ Motherboard Step 1 Step 2 Step 4 - 8 -...
Step 1-1: CPU Installation Figure 1. Socket Pull the rod to the 90-degree directly. Actuation Lever Figure 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then move the socket lever to the locked position while holding pressure on the center of the CPU.
To install the memory module, just push it vertically into the DIMM socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary between sockets. 8VM800M-RZ Motherboard Notch 1. The DIMM socket has a notch, so the DIMM memory module can only fit in one direction.
Step 4: Install AGP Card 1. Read the relate AGP card's instruction document before install the AGP card into the computer. 2. If your AGP card has "AGP 4X/8X(1.5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1.5V). 3.
Page 13
1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard.
Page 14
6) IDE1 / IDE2 (IDE1 / IDE2 Connector) Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. 8VM800M-RZ Motherboard Pin No. Definition...
Page 15
7) SATA0 / SATA1 (Serial ATA Connector) You can connect the Serial ATA device to this connector. If you wish to use RAID function, please use it in unity with BIOS and install the correct driver to have proper operation. 8) F_PANEL (Front Panel Connector) Please connect the power LED, PC speaker, reset switch and power switch etc.
Page 16
Please note, you can have the alternative of using front audio connector or of using rear audio connector to play sound. 11) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. 8VM800M-RZ Motherboard Pin No. Definition MPD+...
Page 17
12) SPDIF_IO (SPDIF In/Out Connector) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it.
Page 18
17) CLR_CMOS (Clear CMOS) You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper. 8VM800M-RZ Motherboard Pin No. Pin No.
Page 19
18) BATTERY CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1. Turn OFF the computer and unplug the power cord. 2.
Chapter 2 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer and pressing <Del>...
Page 22
Change, set, or disable password. It allows you to limit access to the system. • Save & Exit Setup Save CMOS value settings to CMOS and exit setup. • Exit Without Saving Abandon all CMOS value changes and exit setup. 8VM800M-RZ Motherboard - 22 -...
Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Date (mm:dd:yy) Time (hh:mm:ss) IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Drive B Floppy 3 Mode Suport Holt On Base Memory Extended Memory Total Memory : Move Enter: Select...
Page 24
640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. 8VM800M-RZ Motherboard - 24 -...
Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software First Boot Device Second Boot Device Third Boot Device Password Check CPU Hyper-Threading : Move Enter: Select F5: Previous Values " # " System will detect automatically and show up when you install the Intel with HT Technology.
Disable USB 2.0 host controller if you are not using high speed USB devices. Enabled Enable USB 2.0 controller. (Default value) Disabled Disable USB 2.0 controller. USB Keyboard Support Enabled Enable USB keyboard support. Disabled Disable USB keyboard support. (Default value) 8VM800M-RZ Motherboard Integrated Peripherals [Enabled] [Enabled] [Enabled] [Auto] [Enabled] [Enabled] [Enabled] [Disabled]...
Page 27
USB Mouse Support Enabled Enable USB mouse support. Disabled Disable USB mouse support. (Default value) On-Chip LAN Boot ROM This function decide whether to invoke the boot ROM of the onboard LAN chip. Enabled Enable this function. Disabled Disable this function. (Default value) Onboard Serial Port 1 Auto BIOS will automatically setup the port 1 address.
Disabled this function. (Default value) Enabled Power on system by mouse event. PME Event Wake Up Disabled Disable this function. Enabled Enable PME as wake up event. (Default value) 8VM800M-RZ Motherboard Power Management Setup [S1(POS)] Disabled [Instant-Off] [Soft-Off] [Disabled] [Disabled]...
Modem Ring Resume An incoming call via modem can awake the system from any suspend state. Disabled Disable Modem Ring on function. Enabled Enable Modem Ring on function. (Default value) Resume by Alarm You can set "Resume by Alarm" item at "Enabled" and key in data/time to power on system. Disabled Disable this function.
Fan warning function disable. (Default value) Enabled Fan warning function enable. SYSTEM FAN Fail Warning Disabled Fan warning function disable. (Default value) Enabled Fan warning function enable. 8VM800M-RZ Motherboard PC Health Status 1.424V 2.496V 3.296V 11.858V 29°C 3125 RPM 0 RPM...
Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2004 Award Software CPU Clock Ratio Auto Detect PCI/DIMM Clk Spread Specturm CPU Host Clock Control x CPU Clock DRAM Clock AGP OverVoltage Control DIMM OverVoltage Control : Move Enter: Select F5: Previous Values Incorrect using these features may cause your system broken.
Page 32
Increase DIMM voltage may get stable for over-clock. But it may damage to memory module if improper setting this feature. Auto Supply DIMM voltage as memory module required(2.5V). (Default value) +0.1V Increase DIMM voltage +0.1V. +0.2V Increase DIMM voltage +0.2V. 8VM800M-RZ Motherboard - 32 -...
Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.
Setup Menu. If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup. 8VM800M-RZ Motherboard Load Fail-Safe Defaults Load Optimized Defaults...
Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. Type "N"...
Revision History Chapter 3 Install Drivers Install Drivers Pictures below are shown in Windows XP Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe.
Page 38
Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller" under "Device Manager". Please remove the question mark and restart the system (System will auto-detect the right USB2.0 driver). 8VM800M-RZ Motherboard Driver install finished ! You have to reboot system !