Genelec 8030A Datasheet page 4

8030A Data Sheet
Figure 3: The upper curve group shows the horizontal directivity char-
acteristics of the 8030A measured at 1 m. The lower curve shows the
systems power response.
SyStem SpeciFicAtionS
8030A
Lower cut-off frequency, -3 dB < 55 Hz
Upper cut-off frequency, -3 dB > 21 kHz
Free field frequency response 58 Hz – 20 kHz (± 2.0 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged
from 100 Hz to 3 kHz @ 1 m > 100 dB SPL
@ 0.5 m > 106 dB SPL
Maximum long term RMS acoustic
output in same conditions with
IEC-weighted noise (limited by driver
unit protection circuit) @ 1 m > 97 dB SPL
Maximum peak acoustic output per pair
@ 1 m from the engineer with music
material > 108 dB
Self generated noise level in free field
@ 1 m on axis < 10 dB (A-weighted)
Harmonic distortion at 85 dB SPL Freq:
@ 1 m on axis
Drivers Bass
Treble
Both drivers are magnetically shielded
Weight 5.6 kg (12.3 lb)
Speaker dimensions Height
(including Iso-Pod table stand)
Height
(without Iso-Pod table stand)
Width
Depth
Genelec Document BBA0036001a Copyright Genelec Oy 4.2007. All data subject to change without prior notice
50...100 Hz < 2 %
> 100 Hz < 0.5 %
130 mm (5") cone
19 mm ( / ") metal dome
3
4
299 mm (11 / ")
13
16
285 mm (11 / ")
1
4
189 mm (7 7 / ")
16
178 mm (7").
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
Figure 4: The curves above show the effect of the "bass tilt", "treble tilt"
and "bass roll-off" controls on the free field response.
AmpliFier Section
8030A
Bass amplifier output power Short term 40 W (8 Ohm load)
Treble amplifier output power Short term 40 W (8 Ohm load)
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at THD
nominal output SMPTE-IM
CCIF-IM
DIM 100
Signal to Noise ratio, Bass
referred to full output Treble
Mains voltage: 100, 120, 220 or 230 V according to region.
Voltage operating range: ±10 %
Power consumption Idle
Full output
croSSover Section
8030A
Input connector: XLR female, pin 1 gnd, pin 2 +, pin 3 -
balanced 10 kOhm
Output connector: XLR male, pin 1 gnd pin 2 +, pin 3 -
balanced 100 kOhm
Input level for 100 dB SPL output @ 1m -6 dBu at volume control max
Volume control range -80 dB relative to max output
Output signal level is 0 dB relative to input signal level
but adjustable by volume control
Crossover frequency 3.0 kHz
Treble tilt control operating range 0 to –2 dB @ 15 kHz
Bass roll-off control –6 dB step @ 85 Hz
(to be used in conjunction with a 7050A subwoofer)
Bass tilt control 0 to –6 dB @ 100 Hz in 2 dB steps
The 'CAL' position is with all tone controls set to 'off'
and input sensitivity control to maximum and
corresponds to a maximally flat free field response.
In the U.S. please contact: In China please contact:
Genelec, Inc., 7 Tech Circle Beijing Genelec Audio Co. Ltd.
Natick, MA 01760, U.S.A.
Jianwai SOHO, Tower 12, Room 2306
Phone +1 508 652 0900
39 East 3rd Ring Road
Fax +1 508 652 0909
Chaoyang District, Beijing 100022, China
Email genelec.usa@genelec.com
Phone +86 10 5869 7915
Fax +86 10 5869 7914
<0.05 %
<0.05 %
<0.05 %
<0.05 %
>100 dB
>100 dB
10 VA
80 VA
www.genelec.com
In Sweden please contact:
Genelec Sverige
Box 5521, S-141 05 Huddinge
Phone +46 8 449 7070
Fax +46 8 708 7071
Email info@genelec.com