Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gefen DVI-241DL
Summary of Contents for Gefen DVI-241DL
- Page 1 2x1 DVI DL Switcher U S E R M A N U A L www.gefen.com...
- Page 2 Chatsworth, CA 91311 www.gefen.com support@gefen.com Gefen Inc. reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. 2x1 DVI DL Switcher is a trademark of Gefen Inc.
-
Page 3: Table Of Contents
Introduction Features Panel Descriptions Connecting and Operating the DL Switcher Operation Notes RMT2-IR Installation IR Code Confl icts IR Extender Installation Specifi cations Warranty TABLE OF CONTENTS... -
Page 4: Introduction
Our Commitment Gefen will always offer the fi nest quality product at the best possible price. Included in that price is a lifetime of free support from a team of outstanding engineers. Now you can switch easily and reliably between any combination of two dual link DVI &... -
Page 5: Features
• No loss of quality • Use either PC or Mac with USB keyboard/mouse • Switches easily between any two dual link DVI computers • Switch between two dual link DVI, USB 2.0 and Audio Sources • IR Remote control • Rackmountable... -
Page 6: Panel Descriptions
PANEL DESCRIPTIONS Power Indicator Infrared Indicates which Input input is selected Selector Equalization Knobs Contact Closure Interface - Connects to optional wired Audio In 1 Audio In 2 Audio Out RMT-2 remote control DVI In 1 DVI In 2 5VDC Input DVI Out Output USB In 1... - Page 7 6- Plug the 5VDC power supply into the DL Switcher. How to Operate the DL Switcher 1- Use the front panel push button to switch between sources. 2- Use the RMT2-IR remote control port to remotely toggle between sources. 3- Use the optional RMT-2 wired remote control to remotely toggle between sources.
-
Page 8: Operation Notes
This step can be eliminated using the Gefen DVI Detective, which stores the displays EDID. If you loose your picture when switch from source 1 to source 2 or vice-versa you will need a DVI Detective. -
Page 9: Rmt2-Ir Installation
RMT2-IR INSTALLATION 1. Remove battery cover from the back of the RMT2-IR remote. 2. Verify that dip switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. -
Page 10: Ir Code Confl Icts
2. Locate the Dip Switches above the batteries 3. Switch the Dip Switches on the RMT 2-IR to any of the combinations pictured below. 4. Dip Switches 1 and 2 in the RMT 2-IR correspond with Dip Switches 2 and 3 in- side the 2X1 DVI DL Switcher respectively. -
Page 11: Ir Extender Installation
1 Open the unit and move the jumper labeled INFRARED (pictured* as "Step 1" below) from Local to Remote 2 In the bank of switches labeled SERVICE SWITCH (pictured* as "Step 2" below), fl ip Service Switch #1 (top most switch) to the ON position 3 Reassemble the unit. -
Page 12: Specifi Cations
SPECIFICATIONS Video Amplifi er Bandwidth ... 2x 1.65 Gbps Input Video Signal ... 1.2 volts p-p Input DDC Signal ... 5 volts p-p (TTL) Single Link Range ... 3840 x 2400 DVI Input/Output Connector Type ... DVI-I 29 pin female (digital only) USB 2.0 Input Connection ... -
Page 13: Warranty
If equipment fails because of such defects and Gefen Inc. is notifi ed within two (2) years from the date of shipment, Gefen Inc. will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi...