[Trigger 1/2 Setting] - Panasonic PT-AR100EH Operating Instructions (Functional Manual)

[TRIGGER 1/2 SETTING]

You can set the function for each trigger terminal.
Attention
Make sure the <MAIN POWER> switch of the projector
z
is turned <OFF> before a cable is connected to or
disconnected from a trigger terminal.
■
[OUTPUT]
In conjunction with projector operation set in the [TRIGGER
1 SETTING]/[TRIGGER 2 SETTING] menu, a trigger
output signal is sent to an external device with a trigger
terminal to enable control.
■
[INPUT]
Receipt of a trigger input signal from an external device
enables control of projector operation setup in the
[TRIGGER 1 SETTING]/[TRIGGER 2 SETTING] menu.
ON-SCREEN DISPLAY
PICTURE BACK COLOUR
STARTUP LOGO
POSITION AUTO SEARCH
HDMI SIGNAL LEVEL
LANGUAGE FRAME RESPONSE
PROJECTION METHOD
OPTION TRIGGER 1 SETTING
TRIGGER 2 SETTING
HIGH ALTITUDE MODE
LAMP POWER
ECO MANAGEMENT
FUNCTION BUTTON
VIERA LINK SETTINGS
1) Use the ▲▼ buttons to select [TRIGGER
1 SETTING] or [TRIGGER 2 SETTING] and
press the <ENTER> button.
The [TRIGGER SETTING] menu is displayed.
z
TRIGGER 1 SETTING
PICTURE OFF
OUTPUT
POSITION POWER ON
SCREEN AREA MEMORY 1
SCREEN AREA MEMORY 2
LANGUAGE
SCREEN AREA MEMORY 3
OPTION SCREEN AREA MEMORY 4
SCREEN AREA MEMORY 5
SCREEN AREA MEMORY 6
BLANK
DELAY TIME
INPUT
POWER ON/OFF
2)
1/2
BLUE
ON
ON
NORMAL
NORMAL
FRONT/DESK
OFF
OFF
OFF
NORMAL
When the item which is set in the [TRIGGER
1 SETTING]/[TRIGGER 2 SETTING] menu is
chosen or executed in the projector, 12 V is output
from a trigger terminal.
Note
When [AUTO] is selected in the [ASPECT] menu of
z
[POSITION], video is automatically displayed using either
4:3 or 16:9 aspect ratio depending on the input signal,
so if this aspect ratio matches the settings made in
SELECT 4:3 ASPECT
SELECT 16:9 ASPECT
[TRIGGER 1 SETTINGS] or [TRIGGER 2 SETTINGS] 12
SELECT S16:9 ASPECT
V is output.
SELECT JUST ASPECT
SELECT ZOOM ASPECT
•
SELECT H-FIT ASPECT
SELECT V-FIT ASPECT
RS-232C COMMAND LINK
0 SEC.
•
BLANK
[OPTION] menu
Press the ▲▼◄► buttons to select
the input/output function and press the
<ENTER> button.
Function settings
z
Unable to transmit the
trigger output signal. Does
not function even if trigger
[OFF]
input signal is received.
(Trigger input signal can
be received.)
Output
z
[POWER ON]
[SCREEN AREA
MEMORY 1]
[SCREEN AREA
MEMORY 2]
[SCREEN AREA
MEMORY 3]
[SCREEN AREA
MEMORY 4]
[SCREEN AREA
MEMORY 5]
[SCREEN AREA
MEMORY 6]
[BLANK]
[BLANK]
When [BLANK] is activated, output is 12 V. If the
setting is released, output is 0 V.
[RS-232C COMMAND LINK]
Receives commands (  page 88) from external
device and outputs 12 V.
[SELECT 4:3
ASPECT]
[SELECT 16:9
ASPECT]
[SELECT S16:9
ASPECT]
[SELECT JUST
ASPECT]
[SELECT ZOOM
ASPECT]
[SELECT H-FIT
ASPECT]
[SELECT V-FIT
ASPECT]
[RS-232C COMMAND
LINK]
ENGLISH - 65