Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Leica DISTO E7100i
Summary of Contents for Leica DISTO E7100i
- Page 1 Leica DISTO E7500i The original laser distance meter...
-
Page 2: Table Of Contents
Calculator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13 Adjusting measuring reference/tripod - - - - - - - - - - - - - - - - - 14 Leica DISTO E7500i 792324... -
Page 3: Instrument Set-Up
Important paragraphs which must be adhered to in practice as bols above they enable the product to be used in a technically correct and Navigation Function efficient manner. screen Return / Equal Add / Clear / Off Subtract Leica DISTO E7500i 792324... -
Page 4: Basic Measuring Screen
Instrument Set-up Basic measuring screen Selection screen Status bar Page indicator Function / Settings Main line Active function Favorites Settings Help function Leica DISTO E7500i 792324... -
Page 5: Pointfinder (Viewscreen)
We recommend using high quality batteries. Change batteries when battery symbol is flashing. Illumination Crosshair adjustment with navigation keys left and right Zoom (1x, 2x, 4x) with navigation keys up and down Active function Favorites Leica DISTO E7500i 792324... -
Page 6: Operations
(min, max.). The last value measured is displayed in the main line. 2 sec Stops permanent / minimum- maximum measuring. 8.532 m Used to measure room diagonals (maximum val- ues) or horizontal distance (minimum values) Leica DISTO E7500i 792324... -
Page 7: Add / Subtract
Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears dis- placed in the crosshair. In this case rely on the real laser dot. Leica DISTO E7500i 792324... -
Page 8: Settings
Distance units Beep Digital level Keypad lock Favorites Illumination Bluethooth ® Tilt calibration Reset Offset Tilt units Switch between the following units: Exit settings. Confirm setting. ± 90.0° 0.00 % ± 180.0° 0.0 mm/m 360.0° 0.00 in/ft Leica DISTO E7500i 792324... -
Page 9: Distance Units
0 in 1/4 0‘00‘‘ 1/16 0.000 yd 0‘00‘‘ 1/8 Beep ON/OFF Exit settings. To switch ON, repeat procedure. Digital level ON/OFF The digital level is displayed in the status line. To switch ON, Exit settings. repeat procedure. Leica DISTO E7500i 792324... -
Page 10: De-/Activate Keypad Lock
Function is set as Exit settings. Select favorite favorite above the function. corresponding se- lection key. Illumination To save power re- duce bright- ness if not necessary. Exit settings. Confirm setting. Select brightness. Leica DISTO E7500i 792324... -
Page 11: De-/Activate Bluetooth Smart
For more details, see our homepage. Bluetooth standard V4.0) works together with all Bluetooth Smart Ready devices. All other Bluetooth devices do not support the energy saving Bluetooth Smart Module, which is integrated in the device. Leica DISTO E7500i 792324... -
Page 12: Calibration Of Tilt Sensor (Tilt Calibration)
Place device on absolutely flat surface. and place it again on absolutely flat surface. After 2 sec the device 180° goes back to the basic mode. 180° Turn the device horizontally by 180° and place it again on absolutely flat surface. Leica DISTO E7500i 792324... -
Page 13: Reset
Select digit. Adjust digit. value. An offset adds or subtracts a specified value automatically to or from all measurements. This func- tion allows tolerances to be taken into account. The offset icon is Exit settings. displayed. Leica DISTO E7500i 792324... -
Page 14: Functions
Calculator The measurement result from the main line is taken over to the cal- Select key on culator and can be used for fur- display. ther calculations. Ft/in fractions are converted into Meters. Confirm every key. Leica DISTO E7500i 792324... -
Page 15: Adjusting Measuring Reference/Tripod
If device is switched off, reference goes back to standard setting (rear of the device). Confirm setting. Memory 12.208 m 6.554 m 23.889 m Use Up/Down Short cut Switch between navigation keys to measurements. show more re- sults. Leica DISTO E7500i 792324... -
Page 16: Measuring Single Distance
Aim active laser at target. creases. Smart Horizontal Mode 40.8 ° 5.204 m 0.032 m 4.82 7 m Aim laser at tar- get. (up to 360° and a transverse tilt of ±10°) Leica DISTO E7500i 792324... -
Page 17: Height-Profile Measurement
After meas- uring the reference point, the horizontal Horizontal distance to distance and height is displayed for each fol- 2.042 m device lowing point. Exit function. 0.05 4 m Height difference to reference point (REF). Leica DISTO E7500i 792324... -
Page 18: Area
Partial Measurements / Painter function: 3.9I0 m Second distance Press + or - after starting the first measure- ment. Measure and add or subtract distanc- 20.276 m Circumference es. Finish with DIST. Measure 2nd length. 24.3 52 m Area Leica DISTO E7500i 792324... -
Page 19: Volume
Aim laser at third target point. ond target point. target point. 80.208 m Circumference 208.70 3 m Wall areas 24.224 m Ceiling/floor area Use Up/Down 78.6 94 m navigation keys to Volume show more re- sults. Leica DISTO E7500i 792324... -
Page 20: Triangular Area
The long range mode allows measur- ing of difficult targets in unfavorable conditions e.g. bright ambient light or bad target reflectivity. The measuring time is increased. An icon in the status line shows if the function is active. Leica DISTO E7500i 792324... -
Page 21: Inclination Tracking
6.90 1 m ment is positioned in the same navigation keys to Distance between both points vertical plane as the 2 measured show more re- points. The plane is defined of the sults. line between the 2 points. Leica DISTO E7500i 792324... -
Page 22: Height Tracking
The upper point can be targeted with the pointfinder / Use Up/Down crosshair and does not need a reflec- navigation keys to tive laser target as only the inclination is show more re- measured. sults. Leica DISTO E7500i 792324... -
Page 23: Trapezium
Functions Trapezium Aim laser at upper Aim laser at 2nd point. point. 22.70° 78.257 m Trapezium area Use Up/Down 5.90 7 m navigation keys to show more re- sults. Leica DISTO E7500i 792324... -
Page 24: Stake Out
The distance to The function can be stopped the next stake out 0.625 m by pressing the CLEAR/OFF point is displayed. button. 0.24 0 m Approve value "b" and start meas- urement. Leica DISTO E7500i 792324... -
Page 25: Pythagoras (2-Point)
We recommend to use the pythagoras only for indirect 8.29 4 m navigation keys to horizontal measuring. show more re- For height measuring (vertical) it is more precise to use sults. a function with the incliantion measuring. Leica DISTO E7500i 792324... -
Page 26: Pythagoras (3-Point)
We recommend to use the pythagoras only for indi- 18.2 94 m navigation keys to rect horizontal measuring. show more re- For height measuring (vertical) it is more precise to sults. use a function with inclination measurement. Leica DISTO E7500i 792324... -
Page 27: Technical Data
5.6 x 2.28 x 1.14 in Timer Weight (with batteries) 198 g / 6.37 oz Long Range Mode Temperature range: - Storage -25 to 70 °C Calculator -13 to 158 °F - Operation -10 to 50 °C 14 to 122 °F Leica DISTO E7500i 792324... -
Page 28: Message Codes
Hold the instrument Warranty coverage for the entire usage time Heinrich-Wild-Strasse than 10° without any transverse tilt. of the product according to Leica Geosys- CH-9435 Heerbrugg Calibration mistake Make sure, the device is tems International Limited Warranty. Free of placed on a absolutely Internet: www.disto.com... -
Page 29: Permitted Use
Yet, the possibility of causing interference in lations which are unprotected other devices cannot be totally excluded. • Aiming directly in the sun Leica DISTO E7500i 792324... -
Page 30: Fcc Statement (Applicable In U.s.)
• Connect the equipment into an outlet on a CAUTION circuit different from that to which the Looking into the laser beam may be receiver is connected. hazardous to the eyes. • Consult the dealer or an experienced radio/TV technician for help. Leica DISTO E7500i 792324... -
Page 31: Labelling
IEC 60825-1:2007 Maximum radiant power: <1mW Emitted wavelength: 620-690nm Beam divergence: 0.16 x 0.6 mrad Impulse duration: 0.2 x 10 s - 0.8 x 10 Subject to change (drawings, descriptions and technical data) without prior notice. Leica DISTO E7500i 792324... - Page 32 Quality Management and Quality Systems (ISO standard 9001) and Environ- mental Management Systems (ISO standard 14001). Total Quality Management - Our commitment to total customer satisfaction. Ask your local Leica Geosystems agent for more information about our TQM program. Copyright Leica Geosystems AG, Heerbrugg,...