Table of Contents
Advertisement
W4E315-CS22-70
3.2 Nominal data
Motor
M4E068-DF
Phase
1~
Nominal voltage / VAC
115
Frequency / Hz
60
Method of obtaining
ml
data
Valid for approval/
CE
standard
-1
Speed (rpm) / min
1510
Power consumption / W
150
Current draw / A
1.31
Capacitor / µF
14
Capacitor voltage / VDB
250
Capacitor standard
S0 (CE)
Max. back pressure / Pa
80
Min. ambient
-25
temperature / °C
Max. ambient
70
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
4.4 kg
Fan size
315 mm
Rotor surface
Painted black
Blade material
Press-fitted sheet steel blank, sprayed
with PP plastic
Fan housing material
Sheet steel, galvanized and coated with
black plastic (RAL 9005)
Guard grille material
Steel, coated with black plastic (RAL
9005)
Number of blades
5
Airflow direction
"V"
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"F"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
On rotor side
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Axial
Item no. 14329-5-9970 · ENU · Change 96954 · Approved 2017-10-27 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Protection class
Conformity with
standards
1~
Approval
115
60
ml
UL 2111
; Use the device in accordance with its degree of protection.
1510
Information on surface quality
160
The surfaces of the products conform to the generally applicable industrial
1.34
standard. The surface quality may change during the production period.
14
This has no effect on strength, dimensional stability and dimensional
250
accuracy.
UL
The color pigments in the paints used perceptibly react to UV light over
80
the course of time. This does not however in any way affect the
-25
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
70
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
For screw clearance, see Chapter 3.1 Product drawing
Strength class of
screws
; Secure the screws against unintentional loosening (e.g. use self-
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
I (with customer connection of protective
earth)
EN 60335-1; CE
UL 1004-3; CSA C22.2 No. 77
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
locking screws).
+ 80 °C
- 40 °C
Advertisement
Table of Contents
