Nominal Data; Data According To Commission Regulation (Eu) 327/2011; Technical Description; Mounting Data - ebm-papst G2E180-EH03-17 Operating Instructions Manual

G2E180-EH03-01

3.2 Nominal data

Motor M2E074-EI
Phase 1~
Nominal voltage / VAC 230
Frequency / Hz 50
Method of obtaining
fa
data
Valid for approval/ CE
standard
-1
Speed (rpm) / min 1950
Power consumption / W 400
Current draw / A
1.75
Capacitor / µF 8
Capacitor voltage / VDB 400
Capacitor standard S0 (CE)
Min. back pressure / Pa 0
Min. ambient
-25
temperature / °C
Max. ambient 40
temperature / °C
Starting current / A 2.2
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η / %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P / kW
e
09 Air flow q / m³/h
v
09 Pressure increase total p /
sf
Pa
10 Speed (rpm) n / min -1
11 Specific ratio *
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p / 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 10294-5-9970 · ENU · Change 89436 · Approved 2016-08-25 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
1~
230
60
ml
CE
2150
415
1.82
8
400
S0 (CE)
250
-25
30
2
Actual Req. 2015
33.5 33.5
A
Static
44 44
No
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
G2E180-EH03-01
0.22
400
665
2705
1.01
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Weight 5.4 kg
Fan size 180 mm
Rotor surface
Painted black
Impeller material Sheet steel, painted black
Housing material Die-cast aluminum
Direction of rotation Clockwise, viewed toward rotor
Degree of protection IP44; installation- and position-dependent
as per EN 60034-5
Insulation class "B"
Moisture (F) / H0 - dry environment
Environmental (H)
protection class
Installation position Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation On rotor side
drainage holes
Mode S1
Motor bearing Ball bearing
Touch current < 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection
Thermal overload protector (TOP)
internally connected
Protection class I (with customer connection of protective
earth)
Conformity with EN 60335-1; CE
standards
Approval CCC; EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.

3.5 Mounting data

For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Strength class of 8.8
screws
Any further mounting data required can be taken from the product drawing.

3.6 Transport and storage conditions

; Use the device in accordance with its degree of protection.
Max. permitted + 80 °C
ambient temp. for
motor (transport/
storage)
Min. permitted - 40 °C
ambient temp. for
motor (transport/
storage)