Table of Contents
Advertisement
Quick Links
G2E140-AL40-01
CONTENTS
Item no. 11084-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 1 / 11
Operating instructions
·
·
·
1. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1
1.1 Hazard levels for warnings
1
1
These operating instructions use the following hazard levels to indicate
1
potentially hazardous situations and important safety regulations:
1
DANGER
2
Indicates an imminently hazardous situation which will result in
2
death or serious injury if the specified actions are not taken.
2
Compliance with the instructions is imperative.
2
WARNING
2
Indicates a potentially hazardous situation which can result in
2
death or serious injury if the specified actions are not taken.
3
Exercise extreme caution while working.
CAUTION
4
Indicates a potentially hazardous situation which can result in
4
minor or moderate injury or damage to property if the specified
5
actions are not taken.
5
5
NOTE
5
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
6
6
1.2 Staff qualifications
6
The device may only be transported, unpacked, installed, operated,
7
maintained and otherwise used by suitably qualified, trained and
8
authorized technical staff.
9
Only authorized specialists are permitted to install the device, to carry
9
out a test run and to perform work on the electrical installation.
9
1.3 Basic safety rules
9
The safety hazards associated with the device must be assessed again
10
following installation in the final product.
10
The locally applicable industrial safety regulations are always to be
10
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 5.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
·
·
·
Advertisement
Table of Contents
Related Manuals for ebm-papst G2E140-AL40-01
Summary of Contents for ebm-papst G2E140-AL40-01
-
Page 1: Table Of Contents
Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 5.2 Safety inspection. -
Page 2: Safety And Protective Features
Operating instructions G2E140-AL40-01 CAUTION 1.7 Emissions Electric charge on capacitor after device is switched off WARNING Electric shock, risk of injury Depending on the installation and operating conditions, → Discharge the capacitors before working on the device. the sound pressure level may exceed 70 dB(A). -
Page 3: Intended Use
Operating instructions G2E140-AL40-01 2. INTENDED USE The device is exclusively designed as a built-in device for conveying air according to its technical data. Any other usage above and beyond this does not conform with the intended purpose and constitutes misuse of the device. -
Page 4: Technical Data
Operating instructions G2E140-AL40-01 3. TECHNICAL DATA 3.1 Product drawing All dimensions in mm. Cable PVC 4G 0.5 mm², 4x crimped splices Item no. 11084-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 4 / 11 · · ·... -
Page 5: Nominal Data
With regard to cyclic speed loads, note that the rotating parts of the device are designed for a maximum of one million load Motor M2E068-CF cycles. If you have special questions, consult ebm-papst for support. Phase ; Use the device in accordance with its degree of protection. -
Page 6: Connection And Startup
Bearing damage, shorter service life ; If the motor run capacitor was not installed by ebm-papst, check → The fan must not be subjected to force or excessive vibration whether the information on the motor run capacitor matches the from sections of the installation. -
Page 7: Connecting The Cables
Operating instructions G2E140-AL40-01 4.3 Connecting the cables The device has external leads. ; First connect the "PE" (protective earth). Connect the cables according to your application. When doing so, ● observe Chapter 4.4 Connection diagram. Item no. 11084-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 7 / 11 ·... -
Page 8: Connection Diagram
Operating instructions G2E140-AL40-01 4.4 Connection diagram blue brown black green/yellow Item no. 11084-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 8 / 11 · · · · · ·... -
Page 9: Checking Connections
Operating instructions G2E140-AL40-01 4.5 Checking connections 5. MAINTENANCE, MALFUNCTIONS, POSSIBLE CAUSES AND REMEDIES ; Ensure isolation from supply (all phases). ; Make sure a restart is impossible Do not perform any repairs on your device. Send the device to ebm- ;... -
Page 10: Cleaning
Operating instructions G2E140-AL40-01 In the event of further malfunctions, contact ebm-papst. Fastening the Visual inspection At least every Fasten cables 6 months Fastening the Visual inspection At least every Fasten protective earth 6 months 5.1 Cleaning terminal To ensure a long service life, check the fans regularly for proper... - Page 11 ● Dispose of electronic components employing the proper procedures for electronic scrap. → Please contact ebm-papst for any other questions on disposal. Item no. 11084-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 11 / 11 · ·...