Crunch GP508 Owner's Manual

Crunch GP508 Owner's Manual

Active subwoofer system
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

GP508
ACTIVE SUBWOOFER SYSTEM
BENUTZERHANDBUCH
OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GP508 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Crunch GP508

  • Page 1 GP508 ACTIVE SUBWOOFER SYSTEM BENUTZERHANDBUCH OWNER‘S MANUAL...
  • Page 2: Allgemeine Hinweise

    ALLGEMEINE HINWEISE TECHNISCHE DATEN MODELLE GP508 Subwoofer 20 cm (8“) Verstärker Ausgangsleistung RMS 13,8 V 1 x 125 W Ausgangsleistung MAX. 13,8 V 1 x 250 W Signal-Rauschabstand > 91 dB Frequenzgang 20 - 125 Hz Tiefpassfilter 50 - 125 Hz...
  • Page 3 SICHERHEITSHINWEISE BITTE BEACHTEN SIE DIE FOLGENDEN HINWEISE VOR INBETRIEBNAHME! DAS VON IHNEN ERWORBENE GERÄT IST NUR FÜR DEN BETRIEB DAS GERÄT NICHT AN STELLEN EINBAUEN, AN DENEN ES HOHER AN EINEM 12-V-BORDNETZ EINES FAHRZEUGS AUSGELEGT. An- FEUCHTIGKEIT ODER STAUB AUSGESETZT IST. Bauen Sie das Ge- dernfalls besteht Feuergefahr, die Gefahr eines elektrischen Schlages oder rät so ein, dass es vor hoher Feuchtigkeit und Staub geschützt ist.
  • Page 4: Mechanische Installation

    INSTALLATIONSHINWEISE HINWEIS Bevor Sie mit der Installation des Soundsystems beginnen, trennen Sie unbedingt den Massepol der Fahrzeugbatterie ab, um Kurzschlüsse und Stromschläge zu vermeiden. MECHANISCHE INSTALLATION Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgur- te, Tank oder ähnliche Teile beschädigt bzw.entfernt werden.
  • Page 5: Elektrische Anschlüsse

    INSTALLATIONSHINWEISE POWER GAIN ELEKTRISCHE ANSCHLÜSSE FREQUENCY INPUT/REM/GND/+12V/HI IN CONTROLLER 50Hz 125Hz PHASE NORM BEILIEGENDER KABELBAUM MIT STECKER GELB SCHWARZ BLAU-WEISS VOR DEM ANSCHLIESSEN Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten. Ziehen Sie nach der Installation alle Schrauben fest an, denn ein lockerer Anschluss kann eine Fehlfunktion, unzureichende Stromver- sorgung oder Störgeräusche sowie Verzerrungen zur Folge haben.
  • Page 6: Funktionen Und Bedienelemente

    FUNKTIONSHINWEISE POWER GAIN FUNKTIONEN UND BEDIENELEMENTE POWER GAIN FREQUENCY INPUT/REM/GND/+12V/HI IN CONTROLLER FREQUENCY 50Hz 125H INPUT/REM/GND/+12V/HI IN CONTROLLER PHASE NORM 50Hz 125Hz PHASE NORM BEILIEGENDER KABELBAUM MIT STECKER AUX L IN BEILIEGENDES GRAU / GRAU-SCHWARZ KABEL MIT STECKER WEISS / WEISS-SCHWARZ AUX R IN Der GAIN-Regler dient als Lautstärkeregler.
  • Page 7: Fehlerbehebung

    FEHLERBEHEBUNG Fehler: keine Funktion, keine Power LED leuchtet Ursache: Lösung: 1. Die Stromversorgungskabel sind nicht korrekt angeschlossen. Erneute Überprüfung 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. Erneute Überprüfung 3. Die Remote-Steuerleitung des Steuergeräts (Autoradio) ist nicht korrekt am Gerät angeschlossen. Erneute Überprüfung 4.
  • Page 8: General Notes

    GENERAL NOTES SPECIFICATIONS MODELS GP508 Subwoofer 20 cm (8“) Amplifier Output Power RMS 13,8 V 1 x 125 W Output Power MAX. 13,8 V 1 x 250 W Signal-to-Noise Ratio > 91 dB Frequency Range 20 - 125 Hz Lowpass Filter...
  • Page 9: Safety Instructions

    SAFETY INSTRUCTIONS PLEASE NOTE THE FOLLOWING ADVICES BEFORE THE FIRST OPERATION! THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPER-ATION DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE. Other- EXPOSED TO HIGH HUMIDITY AND DUST.
  • Page 10: Installation Instructions

    INSTALLATION INSTRUCTIONS NOTE Before you start with the installation of the sound system, disconnect necessarily the GROUND connection wire from the battery to avoid any risk of electric shocks and short circuits. MECHANICAL INSTALLATION Avoid any damages on the components of the vehicle like air bags, cables, board computer, seat belts, gastank or the like. Ensure that the chosen location provides a sufficient air circulation for the sound system.
  • Page 11: Electrical Interconnection

    INSTALLATION INSTRUCTIONS POWER GAIN ELECTRICAL INTERCONNECTION FREQUENCY INPUT/REM/GND/+12V/HI IN CONTROLLER 50Hz 125Hz PHASE NORM ENCLOSED WIRING HARNESS WITH PLUG YELLOW BLACK BLUE-WHITE BEFORE CONNECTING Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are fixed tight after the installation, because loose connections cause malfunctions, insufficient power supply or interferences.
  • Page 12: Functional Instructions

    FUNCTIONAL INSTRUCTIONS POWER GAIN FEATURES AND OPERATIONAL CONTROLS POWER GAIN FREQUENCY INPUT/REM/GND/+12V/HI IN CONTROLLER FREQUENCY 50Hz 125H INPUT/REM/GND/+12V/HI IN CONTROLLER PHASE NORM 50Hz 125Hz PHASE NORM ENCLOSED WIRING HARNESS WITH PLUG AUX L IN ENCLOSED GREY / GREY-BLACK CABLE WITH PLUG WHITE / WHITE-BLACK AUX R IN The GAIN controller is a volume level controller.
  • Page 13 Malfunction: no function, no power LED Reason: Remedy: 1. The power supply connection of the device is not correct Recheck 2. The cabels have no mechanical or electrical contact Recheck 3. The remote turn-on connection from the head unit to the device is not correct Recheck 4.
  • Page 14 NOTES...
  • Page 15 NOTES...
  • Page 16 Audio Design GmbH Am Breilingsweg 3 · D-76709 Kronau/Germany Tel. +49(0)7253 - 9465-0 · Fax +49(0)7253 - 946510 www.audiodesign.de ©2014 Audio Design GmbH, All Rights Reserved...

Table of Contents