Related Manuals for kincrome KP704
Summary of Contents for kincrome KP704
- Page 1 WET & DRY 1400 WORKSHOP VAC WATT MOTORS 1.5M TANK WITH WITH DRAIN POWER SUCTION TROLLEY HOSE HOSE TAKE OFF 1400 WATT MOTORS TANK WITH DRAIN TROLLEY HOSE KP704...
-
Page 2: Know Your Product
23. 3 Micron Filter Cartridge 24. Brush 25. Crevice Tool 26. Wet Floor Tool 27. Vacuum Tank Removal Clips Model No: ...........................KP704 Total Input Power:......................2400W Motor Power: ........................1400W PTO (Power Take Off) Outlet: ..................Max 1000W (10A) Input: ..........................220 - 240V ~ 50Hz Hose Diameter: ........................35mm... -
Page 3: General Power Tools Safety Warnings
50L WET & DRY WORKSHOP VAC General Power Tools Safety Warnings Save all warnings and instructions for future reference. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 1) Electrical Safety a) Power lead plugs must match the outlet. -
Page 4: Risk Of Electric Shock
50L WET & DRY WORKSHOP VAC 4) Risk of Electric Shock • Never touch the mains plug and the socket with wet hands. • Do not pull the plug from the socket by pulling on the power cable. • Check the power cord with mains plug for damage before every use. If the power cord is damaged, please arrange for the replacement of the cord immediately by an authorized customer service or a skilled electrician. - Page 5 2) Floor Tools (10) or (26) The KP704 50L Wet & Dry workshop Vacuum is supplied with two floor tools. 1. Wet Floor Tool (26): The wet floor tool (26) has a rubber squeegee on both the front and back edge of the floor tool to assist in vacuuming up liquids (fig 3).
- Page 6 50L WET & DRY WORKSHOP VAC Wet & Dry Workshop Vac User Instructions (cont.) 3b) Installation of the Filters - Cloth (20) 1. Remove the motor head (4) from the vacuum tank (14) by releasing the tank retention clips (16) on the side of the vacuum.
- Page 7 4b) Turning ON The Vacuum PTO (Power Take Off) Outlet (17) The KP704 50lt Wet & Dry vacuum is equipped with a PTO (Power Take Off) outlet (17). This PTO outlet (17) is switched seperatly from the vacuum ON/Off switch (18).The PTO outlet (17) (fig 6b) allows you to plug in a seperate power tool (1000W 10A Max) into the vacuum.
- Page 8 50L WET & DRY WORKSHOP VAC 4) Operation (cont.) 4c) Vacuuming Note: When vacuuming dry materials it may be required to open the front or rear face of the wet or dry floor tool (10) or (26) to allow the larger debris (wood shavings, large dirt clumps 5-10 etc.) to be sucked into the vacuum.
-
Page 9: Tank Removal
50L WET & DRY WORKSHOP VAC 5) Tank Tilt The KP704 workshop vacuum is fitted with a tank tilt feature. The tank tilt feature enables you to empty dust and debris from the vacuum tank (14) without needing to lift a full heavy tank. -
Page 10: Troubleshooting
ON/OFF switch (18) to the “ON” “I” position. The Vacuum Cleaner fails Electrical fault Contact Kincrome Customer Service. to start Vacuum will not operate unless a power tool is connected to the PTO outlet (17) and the power tool is switched ON. - Page 11 For further details please visit www.kincrome.com.au or call us. Due to minor changes in design or manufacture, the product you purchase may...
- Page 12 www.kincrome.com.au...
Need help?
Do you have a question about the KP704 and is the answer not in the manual?
Questions and answers