Stanley Fatmax SFMCS701 Original Instructions Manual
  1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Saw
  5. Fatmax SFMCS701
  6. Original instructions manual

Stanley Fatmax SFMCS701 Original Instructions Manual

Hide thumbs Also See for Fatmax SFMCS701:
Table of Contents

Advertisement

Quick Links

Download this manual
www.stanley.eu
SFMCS701

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fatmax SFMCS701 and is the answer not in the manual?

Questions and answers

Related Manuals for Stanley Fatmax SFMCS701

Summary of Contents for Stanley Fatmax SFMCS701

  • Page 1 SFMCS701...
  • Page 2 1 17...
  • Page 7 11 36...

  • Page 8: Intended Use

    Use of an RCD reduces the risk of Intended use electric shock. Your STANLEY FATMAX SFMCS701 sliding compound mitre 3. Personal safety saw has been designed for sawing wood, plastic and nonfer- a. Stay alert, watch what you are doing and use common rous metal only.

  • Page 9: Safety Instructions For Mitre Saws

    (Original instructions) ENGLISH h. Do not let familiarity gained from frequent use of tools Shorting the battery terminals together may cause burns allow you to become complacent and ignore tool or a fire. safety principles. A careless action can cause severe d.

  • Page 10: Additional Safety Instructions For Mitre Saws

    ENGLISH (Original instructions) To make a cut, raise the saw head and pull it out over Unstable support for the workpiece can cause the blade to the workpiece without cutting, start the motor, press bind or the workpiece to shift during the cutting operation the saw head down and push the saw through the pulling you and the helper into the spinning blade.

  • Page 11: Safety Of Others

    This mitre saw has been designed for sawing wood, Ensure that any spacers and spindle rings used are suit- able for the purpose as stated by STANLEY FATMAX. plastic and nonferrous metal only. Do not use the saw Repairs to the cut line guidance system should be carried...
  • Page 12 Be aware of the Chargers following factors influencing exposure to noise: Use your Stanley FatMax charger only to charge the bat- Use saw blades designed to reduce the emitted noise, tery in the tool with which it was supplied. Other batteries Use only well sharpened saw blades, and could burst, causing personal injury and damage.
  • Page 13 Lock down pin (Fig. F) If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Stanley FatMax Service Warning! The lock down pin should be used ONLY when Centre in order to avoid a hazard.
  • Page 14 ENGLISH (Original instructions) Removing the Blade Fully Charged: Remove battery pack (15) from the saw. Green LED Solid Raise the arm to the upper position and raise the lower guard (4) as far as possible. Loosen, but do not remove the guard bracket front screw Hot/Cold Pack Delay: (24) until the bracket (25) can be raised far enough to Green LED Intermittent...
  • Page 15 5 seconds, have the tool serviced by an authorised zero degree position. Set and lock the mitre arm at zero, hold Stanley FatMax service centre. the wood firmly on the table and against the fence. With the Always be sure the blade has stopped before removing it from rail lock screw (18) tightened, turn on the saw by squeezing the kerf.

  • Page 16: Bevel Cuts

    Use the material clamp provided with your saw. To purchase Always let the blade come to a full stop before raising arm. If a material clamp, contact your local retailer or Stanley FatMax small fibres of wood still split out at the rear of the work piece, service centre.
  • Page 17 (Original instructions) ENGLISH Note: Place the clamp on the opposite side of the base when The guard can be raised by hand when installing or removing bevelling. ALWAYS MAKE DRY RUNS (UN-POWERED) BE- saw blades or for inspection of the saw. FORE FINISH CUTS TO CHECK THE PATH OF THE BLADE.

  • Page 18: Cutting Crown Moulding

    ENGLISH (Original instructions) Material up to 3.5" (90 mm) can be cut as described above. 20° 18° Cutting crown moulding In order to fit properly, crown moulding must be compound The chart assumes that all sides are of equal length. For a mitred with extreme accuracy.

  • Page 19: Troubleshooting

    (Original instructions) ENGLISH Minute changes in the mitre angle can be made without af- Warning! To reduce the risk of serious personal injury, DO fecting the bevel angle. This way, when corners other than 90º NOT touch the sharp points on the blade with fingers or hands are encountered, the saw can be quickly and easily adjusted while performing any maintenance.

  • Page 20: Protecting The Environment

    50 x 152 Guarantee 45 deg. mitre left vertical 90 x 15 Stanley Europe is confident of the quality of its products and horizontal 50 x 152 offers consumers a 12 month guarantee from the date 45 deg. bevel left of purchase.
  • Page 21 (Original instructions) ENGLISH...
  • Page 24 United Kingdom Stanley Fat Max Tel. 01753 511234 270 Bath Road Fax 01753 572112 Slough, Berkshire SL1 4DX www.stanleytools.co.uk N909921 REV-0 09/2020...

Table of Contents