Caution:
Never expose your body directly to cool air for a long time. Ex-
cessive exposure to cool air is bad for your health, and should
therefore be avoided.
For fan
Press the [selecting operation] button and bring up the "fan" dis-
play.
•
The fan operation functions to ventilate.
•
The temperature of the room cannot be set by fan operation.
For heating
Press the [selecting operation] button to bring up the "heating"
display.
Regarding displays during heating operation "Under defrosting"
Displayed only during the defrosting operation.
"Under preparation for heating"
Displayed from the start of heating operation until the moment warm
air blows out.
•
When in the "heating" mode, the humidifier will also operate. (For
GUF-50, 100RDH3)
Caution:
•
When the Fresh Master is used together with burners.
•
Never place a burner at a place where it is exposed to the air-
flow from the Fresh Master.
Doing so can result in imperfect combustion of the burner.
•
The microcomputer functions in the following cases:
The intake fan is not moving at the set speed.
Intake fan stops to prevent any cool air from escaping during
the defrosting operation.
3.2.4. Temperature adjustment
GUF-50, 100RDH3 are OA processing unit and cannot adjust the in-
door temperature, even if the procedures given below are followed.
In the case of GUF-50, 100RD3, the indoor temperature can be ad-
justed.
Set temperature display
Room temperature display
˚C
TEMP.
CLOCK→ON→OFF
TIMER SET
PAR-F27MEA
To change temperature
Press the temperature button and set the temperature of your
choice
Pressing
or
once changes the setting by 1°C.
If the pressing is continued, the setting continues to change by 1°C.
•
Indoor temperature can be set within the following range.
Cooling/dry 19 to 30°C
Heating
17 to 28°C
•
It is impossible to set the temperature in fan operation.
*
The range of temperature display is 8° to 39°C. Outside this range,
the display flashes either 8° to 39°C to inform you if the tempera-
ture is lower or higher than the displayed temperature.
8
˚C
ON/OFF
FILTER
CHECK TEST
[temperature] button
In the case of GUF-50, 100RDH3,
set the temperature the same as
the indoor unit.
3.2.5. Fan speed adjustment
Fan speed
display
˚C
TEMP.
CLOCK→ON→OFF
TIMER SET
PAR-F27MEA
To change fan speed
Set the desired fan speed
Every time you press the [fan speed] button once, it switches from the
low-speed or high-speed settings altenatively.
Display of the Remote controller
Low
*
Every time the fan speed adjustment button is once pressed, the
fan speed is changed.
3.2.6. Time setting
Current time display
CLOCK
˚C
TEMP.
[timer] button
CLOCK→ON→OFF
TIMER SET
PAR-F27MEA
•
Set the current time after turning ON the power of the Fresh Master
or after restoration from a power failure.
•
It can be set regardless of the operation of the Fresh Master.
•
During the time operation, the time-setting button becomes void,
disabling time setting.
Press the [time selection] button and bring up the "current time"
display
•
Every time it is pressed, the display changes.
"current"
"start"
time
time
Caution:
When the current time is not yet set, the "current" time display
flashes, disabling the setting of timer operation.
Set the current time by pressing the time setting
button
•
The time cannot be set while the "[timer]" is displayed.
•
While the "CLOCK" time is displayed, press the time setting
buttons and set the time.
˚C
ON/OFF
FILTER
[fan speed]
CHECK TEST
button
High
Time display
OFF
˚C
ON/OFF
[time selection]
FILTER
button
CHECK TEST
[time setting]
button
"end"
(no display)
time
or
/