Subscribe to Our Youtube Channel
Related Manuals for Trigon Electronics 02A00311
Summary of Contents for Trigon Electronics 02A00311
- Page 1 Miniguard HF-2 Series Handsfree Telephone Entry Autodialer INSTALLATION OPERATIONAL INSTRUCTIONS (Firmware revision #020700 Rev. A HF2XTRA) with 10 number rollover www.EmergencyTelephoneTowers.com | (800) 878-7829...
-
Page 2: Table Of Contents
MINIGUARD HF-2 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION ..................PRODUCT OVERVIEW ................MOUNTING ....................WIRING ..................... WIRING DIAGRAM ................PROGRAMMING Entering Program Mode ................Setting Operational Modes ..............Entering Autodialed Telephone Numbers ..........Verifying Autodialed Telephone Number .......... -
Page 3: Introduction
Alarm Shunt Relay A Site I.D. code feature provides for unit identification. TRIGON ELECTRONICS ORANGE CA. Secondary The Site I.D. code is a programmable four digit code Relay that is transmitted by the HF-2 when it receives a Camera, Door or Gate command from the called party. -
Page 4: Mounting
MINIGUARD HF-2 MOUNTING MOUNTING MOUNTING MOUNTING MOUNTING Arrangements must be made with the local telephone 3.62" company for installation of a standard voice-grade .52" telephone line (touch-tone or rotary) as close to the unit mounting location as possible. The telephone company may require the following information. -
Page 5: Wiring Diagram
MINIGUARD HF-2 WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM RS-232 Printer ALARM SHUNT 1/4 Amp RELAY; Busy MICROPROCESSOR CARD READER MICROPHONE (HF-2) MEMORY SPEAKER (HF-2) AUDIO MOUTH SPEAKER PRIMARY EARPHONE RELAY VOLUME 5 Amp MAX EARTH GROUND TELEPHONE LINE INPUT Telephone line cabling... -
Page 6: Programming
MINIGUARD HF-2 PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION General Programming Information Fourth Auto dial Number (12 digit max) The "Initial Setup" for the HF-2 has been programmed __ __ __ __ __ __ __ __ __ __ __ __ at the factory. -
Page 7: Setting The Site Id Number
MINIGUARD HF-2 PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. 5. If desired, exit Program Mode by pressing '#' (E) Setting the Site ID Number: (wait for two second tone). This number identifies the unit upon request from a 6. -
Page 8: Operation
MINIGUARD HF-2 OPERATION OPERATION OPERATION OPERATION OPERATION STANDARD MODE Note: If the wrong Program code is entered, the unit will immediately hang up. If the program code or other When a CALL button is pressed, the HF-2 dials a pre- information is not entered completely, the HF-2 will programmed phone number and monitors the line for time-out and hang up. -
Page 9: Trouble Shooting Guide
MINIGUARD HF-2 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE NO DIAL TONE LOSES MEMORY 1. Check input power at unit. Should be 12 VAC. 1. Electrical noise on power line. Install EMI/RFI filter. -
Page 10: General
MINIGUARD HF-2 CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING General Data between [ ] is a mandatory program key stroke sequence. Data between { } is to be supplied by the programmer. Unit responses are shown between ( ). -
Page 11: Kit Wiring Diagram
MINIGUARD HF-2 HF-2 KIT Wiring Black - Speaker Red - Speaker Yellow - Telco White - Call Btn Yellow - Telco White - Call Btn Blue - Ground Brown - 12VAC Brown - 12VAC Black - LED Violet - Relay(primary) Red - LED Violet - Relay(primary) Green - Mic... - Page 12 MINIGUARD HF-2 Page 12...
Need help?
Do you have a question about the 02A00311 and is the answer not in the manual?
Questions and answers