Trigon Electronics Minipak Installation And Operation Instructions Manual
  1. Manuals
  2. Brands
  3. Trigon Electronics Manuals
  4. Intercom System
  5. Minipak
  6. Installation and operation instructions manual

Trigon Electronics Minipak Installation And Operation Instructions Manual

Multi-number telephone entry system
Hide thumbs Also See for Minipak:
Table of Contents

Advertisement

Quick Links

See also: Programming Manual
Minipak
Multi-Number Telephone Entry System
INSTALLATION
and

OPERATION INSTRUCTIONS

Universal SMT Version
255 Glider Circle • Corona, CA 92880
(800) 842-7444• Info@trigonelectronics.com
www.TrigonElectronics.com
August 6, 2008

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Minipak and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Trigon Electronics Minipak

Summary of Contents for Trigon Electronics Minipak

  • Page 1: Operation Instructions

    Minipak Multi-Number Telephone Entry System INSTALLATION OPERATION INSTRUCTIONS Universal SMT Version 255 Glider Circle • Corona, CA 92880 (800) 842-7444• Info@trigonelectronics.com www.TrigonElectronics.com August 6, 2008...

  • Page 2: Table Of Contents

    Minipak TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION ..................PRODUCT OVERVIEW ................MOUNTING ....................WIRING ..................... WIRING DIAGRAM ................SYSTEM SETUP Enter Program Mode Locally ..............Enter program Mode Remotely ...............

  • Page 3: Introduction

    Shielded or Twisted, 2 Conductor The Minipak has a capacity of up to 400* telephone numbers and up to 400* personal entry codes, and is PBX compatible. It is constructed for rugged outdoor Power Cabling - use.

  • Page 4: Mounting

    Minipak MOUNTING MOUNTING MOUNTING MOUNTING MOUNTING Arrangements must be made for the installation of a Figure 2 standard voice-grade telephone line (touch-tone or rotary, telco or PBX Port), as close to the unit mounting 9.35" 9.35 in location as possible. The telephone company may 1.00"...

  • Page 5: Wiring Diagram

    WIRING DIAGRAM WIRING DIAGRAM Relay #2 Second Relay is Standard 5 AMP on HF-2, HS-2, M GIID Relay 100BD, MP4000 Second Relay is Optional on MGII, 100B, Minipak, NO C T.A.C. 500,1000,1500 Microprocessor relay 2 Spkr Play Microphone Speaker Adjustm ent...

  • Page 6: System Setup

    SYSTEM SETUP SYSTEM SETUP SYSTEM SETUP SYSTEM SETUP SYSTEM SETUP Minipak General Programming Information: (F) Enter Gate Interval: The "Initial Setup" for the Miniguard IID has been "Gate Interval" refers to the length of time the output programmed at the factory. These factory default settings relay (parking gate, front entry, etc.) will stay engaged...

  • Page 7: Programming

    Minipak PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING (A) Programming after Set-up: (D) Programming Entry Codes: In order to program the unit, it must be in the Program Entry Codes make it possible for the resident to enter a Mode. If you came from SETUP and didn’t exit or reset, Code (P.I.N.

  • Page 8: Entering Access Cards

    Identification Code makes it possible for the party makes it possible for the user to use an access card at the receiving a call from a Minipak to identify which “gate” unit and gain entry. Each card entered is converted to a is calling.

  • Page 9: Programming Primary Relay "On" Time

    3. Enter Start Time (Use military format of This procedure allows selective or complete deletion of hours:minutes, i.e. “0600” , “1500”). Entry must be all data in the Minipak’s memory. Also, it is possible to four digits. reset the Minipak back to its factory defaults (presets).

  • Page 10: Recording A New Voice Message

    Minipak PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING (O) Recording a new voice message. (O) Recording a new voice message. (O) Recording a new voice message. (O) Recording a new voice message. (O) Recording a new voice message. To change the voice message on the voice chip follow these steps: 1.

  • Page 11: Operation

    Refer to the SETUP section in this manual. To latch (hold closed) a relay, place a telephone Unlatch Door / Gate call to the Minipak. The Minipak will auto-answer and (Optional) you will hear a brief tone in the speaker. Refer to Fig. 5...

  • Page 12: Remote Operation Time-Out

    Remote Operation Time-out: Printer Operation: (Optional) If you call the unit to operate it remotely, you have 30 The Minipak can support an audit log output to a remote seconds until auto-termination. Any tone instruction serial printer up to 300 feet away.

  • Page 13: Trouble Shooting

    Minipak TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE NO DIAL TONE LOSES MEMORY 1. Check (check fuse) input power at unit. Should be 1. Electrical noise on power line. Install EMI/RFI 12 VAC.
  • Page 14 Minipak USE AND PROGRAMMING GUIDE, Contiued USE AND PROGRAMMING GUIDE, Contiued USE AND PROGRAMMING GUIDE, Contiued USE AND PROGRAMMING GUIDE, Contiued USE AND PROGRAMMING GUIDE, Contiued General: [ 4] Verify Relay One Schedule (hhmm hhmm d d #, = not set) Data between [ ] is a mandatory program key stroke sequence.

  • Page 15: Specifications / Features

    Minipak Specifications / Features Design- Handsfree telephone with programmable internal auto dial capability and remote control of relays. Capacity - 24, 50, 125, 300, or 400 residents. Capacity includes 1 to 4 digit directory code, 4 digit direct entry code, and up to 16 digit tele- phone number for each resident.
  • Page 16 Minipak Page 16...

Table of Contents