Midea WQP6-3607 Manual
  1. Manuals
  2. Brands
  3. Midea Manuals
  4. Dishwasher
  5. WQP6-3607
  6. Manual

Midea WQP6-3607 Manual

Hide thumbs Also See for WQP6-3607:
Table of Contents

Advertisement

Quick Links

Introduction
WQP6-3607 compact electrical dishwasher with 6 washing cycles offers good washing
performance to satisfy every washing requirement. Its electronic control is easy and convenient to
operate. The rack can hold up to 6 sets of dishes. The size (width * depth * height: 550mm *
500mm * 438mm) can easily fit in any corner of the kitchen, and it s recommended to locate at
which the water hose connection is accessible.
Specification
Rated voltage:
Rated power:
Water pressure:
Water temperature:
Capacity:
Control Panel Features
Note
: all models have different control panel features and appearances. All detail can be
referred to user manuals of the model.
220~240V / 50Hz
1170-1380W
0.04~1.0MPa
maximum 60
6 settings
3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WQP6-3607 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Midea WQP6-3607

Summary of Contents for Midea WQP6-3607

  • Page 1 Introduction WQP6-3607 compact electrical dishwasher with 6 washing cycles offers good washing performance to satisfy every washing requirement. Its electronic control is easy and convenient to operate. The rack can hold up to 6 sets of dishes. The size (width * depth * height: 550mm * 500mm * 438mm) can easily fit in any corner of the kitchen, and it s recommended to locate at which the water hose connection is accessible.

  • Page 2: Component Locator Views

    Component Locator Views Front View Part Name:1 control panel 2 outer door 3 kick board Interior View (with basket) Part Name: 1 cutlery basket 2 basket 3 dispenser 4 inner door...

  • Page 3: Dishwasher Components

    Interior View (With Basket Removed) Part Name: 1 Nut of air breaker 2 Water Softener cover 3 Sprayer 4 Filter System Back View Part Name: 1 Bottom board 2 Power cord 3 Inlet hose connecter 4 Outer drain hose Dishwasher Components Note : Throughout this manual, features and appearance may vary from your model.

  • Page 4: Main Control Board

    or higher. After service is completed, be sure all safety grounding circuits are complete, all electrical connections are secure, and all access panels are in place. Main control board The main control board controls all electrical elements in the dishwasher machine. It located in the protecting box in the bottom of dishwasher machine.

  • Page 5: Floater Assembly

    Floater assembly Snaps Terminlals Part Name: 1 cover of bottom board 2 microswitch 3 floater holder 4 floater Removal and Replacement Remove cover of bottom board. (see main control board removal and replacement) Pull out all terminals of microswitch. Unfit snaps fixing microswitch to floater holder. Snaps Unfit snaps fixing floater holder to cover of bottom board.

  • Page 6: Heating Pump Assembly

    Part Name: 1 heating pump assembly 2 lower pump cover 3 motor assembly 4 motor hunger Removal and Replacement Remove cover of bottom board. (see main control board removal and replacement) Pull out all terminals of heating pump motor assembly. Terminals Terminals Clamps...

  • Page 7: Motor Assembly

    Part Name: 1 upper pump cover 2 heating element 3 pressure switch assembly Removal and Replacement Take out heating pump motor assembly from the dishwasher machine. (see main heating pump motor assembly removal and replacement) Snap Unfit snap of heating pump assembly, and contrarotate heating pump assembly. Reverse the above procedure to install.

  • Page 8: Drain Pump Assembly

    Screws Part Name: 1 motor hunger 2 impeller assembly 3 pump seal ring 4 lower pump 5 motor assembly Removal and Replacement 1. Take out heating pump motor assembly from the dishwasher machine. (see main heating pump motor assembly removal and replacement) 2.

  • Page 9: Check Plate

    Pull out all terminals of drain pump assembly. Unfit snap of drain pump assembly, and contrarotate drain pump assembly to take it out. Snap Terminals Reverse the above procedure to install. And check out all connectors connected well. Check plate Removal and replacement Remove cover of bottom board.

  • Page 10: Control Panel

    Clamps Terminals Remove clamp for fixing connecting hose to inlet valve, and contrarotate inlet valve to take it out. Reverse the above procedure to install. And check out all connectors connected well. Control Panel The outer door covers the door to the dishwasher and protects the detergent dispenser. Removal and Installation 1.

  • Page 11: Operating Board

    Operating board Removal and Replacement 1. Disconnect power supply. 2. Remove all screws for fixing control panel. (see control panel removal and installation) 3. Put out all housings for connecting operating board. 4. Remove screw and unfix all snaps for fixing the operating board. (see control panel removal and installation) 5.

  • Page 12: Inner Door

    Dispenser The dispenser automatically dispenses both the detergent and the rinse agent at the appropriate times. The dispenser is activated twice during a wash cycle. The first time, the dispenser is activated, the lever slides up the right-hand path of the connecting rod.
  • Page 13 Removal and Replacement 1. Remove outer door assembly. (see outer door removal and installation) 2. Remove control panel .(see control panel removal and installation) 3. Remove dispenser. (see dispenser removal and replacement) 4. Remove all screws for fixing inner door to right hinge assembly and left hinge assembly. Screws 5.

  • Page 14: Door Lock Assembly

    Part Name: 1 door switch assembly 2 absorber 3 4 backboard Door Lock Assembly Removal and Replacement 1. Disconnect power supply. 2. Remove shell. (see shell removal and installation) 3. Unfit snap of door lock assembly, and push it out. Snap Locking terminals 4.

  • Page 15: Hinge Assembly And Spring System

    snap 5. Turn the dishwasher machine, remove the cover of bottom board. (see main control board removal and installation) 6. Remove all clamps for fixing connecting hoses to air breaker. 7. Reverse the above procedure to install. And check out all connectors connected well. Hinge assembly and Spring system Part Name: 1 spring holder 2 spring 3 friction strip 4 absorbing cotton 5 hinge assembly...

  • Page 16: Tank Assembly

    4. Remove all screws for fixing hinge assembly to bottom board. Screws 5. Reverse the above procedure to install. And check out all connectors connected well. Tank assembly Removal and Installation 1. Remove shell. (see shell removal and installation) 2. Take out absorbing cotton. 3.

  • Page 17: Troubleshooting

    Troubleshooting SYMPTOM CHECK FOR THE FOLLOWING REMEDY Error:E1 The water supply is turned off. Turn the water supply on. Defective water fill valve. Replace the water fill valve. Dishwasher Low water pressure. Minimum water pressure of 20 PSI. will not fill with water or will not Disassemble and clean the water fill valve and Obstructed water fills valve or hose.
  • Page 18 protector Defective motor bearings. Replace the motor. Repeated dishwasher Defective PCB assembly Replace the PCB assembly cycles. Water remains in This is necessary to keep the pump primed and is A small amount of water (in sump area) bottom drained automatically at the beginning of each is normal.

Table of Contents