Instructions Manual for BP-480 (W4346) 04/11/2019 TABLE OF CONTENT SPECIFICATIONS WARNINGS SAFETY INSTRUCTION FOR MACHINERY IDENTIFICATION FRONT SIDE OF BAND SAW REAR OF BAND SAW OPERATING INSTRUCTION LIFTING AND PLACING ASSEMBLING ADJUSTING 90 DEGREE TABLE STOP ASSEMBLING RIP FENCE CHANGING BLADES...
Instructions Manual for BP-480 (W4346) 04/11/2019 2. WARNINGS − − Misuse of this machine can cause ser rious injury. Never leave machine ru unning while you are away from it. − − Always shut off the mac chine when not in use.
Instructions Manual for BP-480 (W4346) 04/11/2019 GENERAL ELECTRICAL CAUTIONS Caution: This saw should be grounded in accordance with the National For circuits which are far away from the electrical Electrical Code and local codes and ordinances. This work should service box, the wire size must be increased in order to deliver be done by a qualified electrician.
Instructions Manual for BP-480 (W4346) 04/11/2019 4. IDENTIFICATION Throughout this document, we make reference to various systems Where detailed illustrations for various subsystems will be helpful, and components on the saw. The two illustrations on these pages will you will find these illustrations accompanying the specific teat for provide you with an overall frame of reference for the location and each subsystem and its components.
Instructions Manual for BP-480 (W4346) 04/11/2019 OPERATING INSTRUCTION LIFTING AND PLACING On the day that the machine arrives, make sure that a crane or forklift with sufficient capacity is available to Eye Bolt unload the machine from the vehicle. Ensure access to the chosen site is clear and that doors...
Instructions Manual for BP-480 (W4346) 04/11/2019 ADJUSTING 90 DEGREE TABLE STOP 1. Unplug power cord. Loosen the lock knobs (see Figure 5) and tilting table left until it rests against table stop bolt M8. (A, Fig. 6) Figure 5 2. Use a protector placed on the table and against the Figure 6 blade (Fig.
Instructions Manual for BP-480 (W4346) 04/11/2019 ADJUSTING THE TENSION OF BLADE Blade tension is set by a spring loaded tension mechanism on the upper wheel. Check the level of the tension device before cutting. The tension for various blade widths as indicated on the window of upper wheel cover.
Instructions Manual for BP-480 (W4346) 04/11/2019 MITER GAUGE ADJUSTMENT 1. Place the miter gauge in the table slot. 2. Loosen the clamp screw on the miter gauge. 3. Adjust the desired angle of cutting on the miter gauge. 4. Tighten the clamp screw. (see Figure 16)
Instructions Manual for BP-480 (W4346) 04/11/2019 6. STEPS FOR THE TABLE PARALEEL ADJUSTMENT Insert table pin into table groove. (see Figure 1) Table Pin Figure 1 Use a ruler gauge and put it on the table. Adjust the position of the table pin...
Page 21
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 22
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 23
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 24
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 25
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 26
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 27
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 28
Instructions Manual for BP-480 (W4346) 04/11/2019...
Page 29
Instructions Manual for BP-480 (W4346) 04/11/2019 26 26...
Page 30
Instructions Manual for BP-480 (W4346) 04/11/2019 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used.
Page 31
Instructions Manual for BP-480 (W4346) 04/11/2019 Wood Bandsaw Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. 11. Work area hazards. Make sure the bandsaw is turned Keep the area around the off and disconnect from the main power supply bandsaw clean from oil, tools, chips.
Page 32
Instructions Manual for BP-480 (W4346) 04/11/2019...
Need help?
Do you have a question about the W4346 and is the answer not in the manual?
Questions and answers