AVERATEC AV6110-EH1 Getting To Know Manual page 71

■ appendix B agency regulatory notices
Fede ral Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rule s. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
equip ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instru ctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occu r in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
deter mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
follow ing measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.
Mod ifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly appro
by th e Manufacture may void the user's authority to operate the equipment.
Conn ections to Peripheral Devices
Conn ections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compl
with FCC Rules and Regulations.
Decl aration of Conformity
This device complies with Part 15/68 the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
caus e harmful interference, and (2) this device must accept any interference received, including interference that may cause
unde sired operation.
Euro pean Notice
Prod ucts with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) and
R&T TE Directive (1999/5/EC) issued by the Commission of the European Community.
Com pliance with these directives implies conformity to the following European Norms:
EN55022 (CISPR 22) Radio Frquency Interference
EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic Immunity
EN 300 328-2 (ETS 300 328) Radio Spectrum Matter.
TBR21 (ETS TBR21) Terminal Equipment.
EN60950 (IEC950) I.T.E. Product Safety
Cana dian Notice
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio
interf erence regulations of the Canadian Department of Communications.
Le pr esent appareil numerique nemet pas de bruits radioelectriques depassant les limites applicables aux appareils nume
de Cl asse B prescrites dans le reglement sur le brouillage radioelectrique edicte par le Ministere des Communications du
Cana da.
Pow er Cord Requirement
The power cord supplied with the AC adapter should match the plug and voltage requirements for your local area. Regulator
appr oval for the AC adapter has been obtained using the power cord for the local area. However, if you travel to a different area
and n eed to connect to a different outlet or voltage, you should use one of the power cords listed below. To purchase a power
cord (including one for a country not listed below) or a replacement ac adapter, contact your local dealer.
U.S. and Canada
The cord set must be UL-Listed and CSA-Certified or C-UL Listed.
The minimum specifications for the flexible cord are (1) No. 18 AWG, (2) Type SJ, and (3) 3-conductor.
The cord set must have a rated current capacity of at least 10 A.
The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V)
B-2
This
be
ved
iance
riques
y