Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Apevia X-Supra
Summary of Contents for Apevia X-Supra
- Page 1 USER’S MANUAL...
-
Page 2: Table Of Contents
1. Motherboard installation...1 2. Install 5¼” and 3½” 3. Install PCI components...4 4. Case fan setup...5 5. Connect case leads to motherboard...6 Identify the power supply connectors 7. Case Accessories...8 8. Adding a front case fan (optional)...8 9. Complete the installation...9 10. -
Page 3: Motherboard Installation
NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions. 1. Motherboard installation: 1.1 Remove thumbscrews from the rear of the X-Supra. X-Supra Finished Appearance 1.2 Grab the notch on the left panel. Pull until the panel... - Page 4 1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel. NOTE: Touch an unpainted metal section of the case to discharge static before handling components (with power supply plugged into AC outlet, but NOT the motherboard). An anti-static wrist-strap should also be worn to further minimize the possibility of damage.
-
Page 5: Install 5¼" And 3½" Drives
2. Install 5¼” and 3½” 2.1 To install an optical or floppy drive, first remove the metal shields that sit behind each drive bay cover. This must be done from the inside of the case. Next remove the drive bay covers by using a screwdriver, and knocking them out from behind. -
Page 6: Install Pci Components
2.5 Align rails with hard-drive bay and insert. 3. Install PCI components: 3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch. 3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis. -
Page 7: Case Fan Setup
3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.). 4. Case fan setup: 4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. -
Page 8: Connect Case Leads To Motherboard
5. Connect case leads to motherboard: 5.1 Locate the top panel leads. 1 x USB 1 x 1394 1 x HD AUDIO 5.3 Locate the front panel leads. 1 x Power SW 1 x Reset SW 1 x H.D.D. LED 1 x Pow LED +/- 1 x Speaker 5.2 Connect leads to motherboard head-... -
Page 9: Identify The Power Supply Connectors
6. Identify the power supply connectors: (Power supply version only) 6.1 20/24 pin ATX connector X 1 6.3 Serial ATA (SATA) connector X 2 6.5 6pin PCI-Express connector X 1 Connect PC components to the required power connector for each device type. 6.2 ATX 12V P4 CPU connector X 1 6.4 4pin peripheral connector X 6 6.6 Floppy drive connector X 2... -
Page 10: Case Accessories
7.2 The bracket shown can be screwed to the rear of the case, allowing a lock to be used for security purposes. 8.2 Next, remove the X-Supra’s front panel. Get a firm grip on the intake vent at the bottom of the front panel and pull. -
Page 11: Complete The Installation
9. Complete the installation: 8.1 With components properly installed, gently return front and side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Supra ATX chassis. -
Page 12: Usb/1394/Audio Cable Module Assignments
10. USB/1394/Audio cable module assignments:...
Need help?
Do you have a question about the X-Supra and is the answer not in the manual?
Questions and answers