Table of Contents
Advertisement
Installation Guide (continued)
安裝指南（續）
Connecting the water supply hose to the washer
供水管與機體的連接
Firmly tighten the union nut
when connecting the water
supply hose to the water inlet.
沿箭頭方向旋轉連接 絲 母，使其
與供水口緊緊相連。
• Loosely tightened union nut will cause water leakage.
請務必擰緊供水管與機體的連接 絲 母。否則，將會漏水。
• When removing the hose, unscrew the union nut fi rst.
拆卸供水管時，先鬆開連接 絲 母，再進行拆卸。
1
Confi rm the diameter of the water tap.
確認水龍頭直徑。
• If the diameter exceeds
2cm, remove the joint
ring.
若水龍頭的外經超過
2cm，可將連接環取出。
3
Press the sealed
pad evenly
against the
tap and tighten
the four screws
uniformly.
將密封墊均勻地壓
在水龍頭上，再將
4個螺釘均等地擰
緊。
• For water supply hose installation, please refer to "How to install the water supply hose" in the user manual.
供水管的安裝參閱使用說明書中「供水管的安裝」一章。
• Loosening may occur after a long time use. In such a case, reinstall the joint following steps 2 to 4.
長時間使用後，可能會因鬆脫而引起漏水，此時請按2~4的步驟重新安裝。
(Follow the same steps when reinstalling the one touch joint when you move the machine to another location.)
（搬家等需重新安裝便捷連接器時，請按照相同的步驟進行。）
Appropriate water tap
適用的水龍頭
Horizontal tap A
Horizontal tapB
橫式A型水龍頭
橫式B型水龍頭
10
How to Install the Water Supply Hose
供水管的安裝
Union nut
How to Install the One Touch Joint
便捷連接器的安裝
Screw
Joint ring
Label
One touch joint
Water tap
Sealed pad
B
Joint
B
Tighten screw in advance if
it is located close to the wall.
Horizontal taps A and B as shown below.
橫式A、B型水龍頭最為適宜。
Square mouth tap
方口水龍頭
Distance must be over 1.6cm
in order to install correctly.
1.6cm
Extending the water supply hose
供水管的延長
Please use optional extension pipe
to extend length of the water supply
hose.
請使用另行銷售的延長供水管。
• Three standard extension hoses (1m,2m,3m)
are available. Please inquire distributors for
extending the water supply hose.
備有1m 、2m和3m三種規格供購買。如欲延長供
水管，請向銷售商查詢。
2
Check the distance between
joints A and A .
確認接頭 A 、 B 之間的間隙。
• Screw joint B in the
arrow direction to adjust
the gap.
沿箭頭方向旋轉接頭B調
整間隙。
4
Tighten joint B in
the arrow direction
to reduce the gap
between joint A and
B to 4mm or less.
沿箭頭方向擰緊接頭
B ，使接頭A 、 B
之間的間隙在4mm
以內。
Universal household tap
萬能水龍頭
May break off after installing
the one touch joint.
A
Joint
A
Approximately 6mm
6mm
B
Joint
B
A
Joint
A
(After tighten)
(
)
Less than 4mm
4mm
B
Joint
B
Swivel tap
萬向水龍頭
Water leakage
may occur.
Advertisement
Table of Contents
