Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and Navigation Function efficient manner. screen Return / Equal Add / Clear / Off Subtract Leica DISTO E7500 820692...
Instrument Set-up Basic measuring screen Selection screen Status bar FUNC Function / Settings Main line Active function Favorites Settings Help function Leica DISTO E7500 820692...
We recommend using high quality batteries. Change batteries when battery symbol is flashing. Illumination Crosshair adjustment with navigation keys left and right Zoom (1x, 2x, 4x) with navigation keys up and down Active function Favorites Leica DISTO E7500 820692...
(min, max.). The last value measured is displayed in the main line. 2 sec Stops permanent / minimum- maximum measuring. 8.532 m Used to measure room diagonals (maximum val- ues) or horizontal distance (minimum values) Leica DISTO E7500 820692...
Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears dis- placed in the crosshair. In this case rely on the real laser dot. Leica DISTO E7500 820692...
0 in 1/4 0‘00‘‘ 1/16 0.000 yd 0‘00‘‘ 1/8 Beep ON/OFF Exit settings. To switch ON, repeat procedure. Digital level ON/OFF The digital level is displayed in the status bar. To switch ON, Exit settings. repeat procedure. Leica DISTO E7500 820692...
Settings De-/Activate keylock Switch on with keylock To deactivate, repeat procedure. The keylock is active if device is switched off. within Exit settings. 2 sec Leica DISTO E7500 820692...
Place device on absolutely flat surface. and place it again on absolutely flat surface. After 2 sec the device 180° goes back to the basic mode. 180° Turn the device horizontally by 180° and place it again on absolutely flat surface. Leica DISTO E7500 820692...
Function is set as Select favorite Exit settings. selection-key in favorite above the function. the measuring corresponding se- mode. lection key. Illumination To save power re- duce bright- ness if not necessary. Exit settings. Confirm setting. Select brightness. Leica DISTO E7500 820692...
The offset icon is Exit settings. displayed. Reset Second confirmation with selection keys: Reset returns the instrument to the factory settings. All custom- Refuse: Confirm: ized settings and memories are lost. Exit settings. Leica DISTO E7500 820692...
Adjusting measuring reference Stake out Pythagoras 1 Memory Single Distance Measurement Smart Horizontal Mode Area Timer The self release starts if ON/Measure key is pressed. 30 sec Confirm setting. Select release 5 sec time. 2 sec Leica DISTO E7500 820692...
Page 15
Functions Adjusting measuring reference/tripod Distance is measured from the rear of the device (standard setting). Distance is measured from a Leica DISTO Adapter FTA 360 (lock symbol = perma- nently) Distance is measured from the tripod thread permanently. Distance is measured from the front of the device (lock symbol = permanently).
Aim active laser at target. creases. Smart Horizontal Mode 40.8 ° 5.204 m 0.032 m 4.82 7 m Aim laser at (up to 360° and a transverse target. tilt of ±10°) Leica DISTO E7500 820692...
Partial Measurements / Painter function: 3.9I0 m Second distance Press + or - before starting the first measure- ment. Measure and add or subtract distanc- 20.276 m Circumference es. Finish with =. Measure 2nd length. 24.3 52 m Area Leica DISTO E7500 820692...
Use Up/Down 5.744 m 13.430 m First distance Ceiling/floor area navigation keys to show more re- 2.338 m 39.300 m Second distance Wall areas sults. 2.431 m 16.164 m Third distance Circumference 32.6 53 m Volume Leica DISTO E7500 820692...
The distance to The function can be stopped the next stake out by pressing the CLEAR/OFF 0.625 m point is displayed. button. Approve value "b" 0.24 0 m and start meas- urement. Leica DISTO E7500 820692...
Minimum or Maximum measure- ment. 21.383 m We recommend to use the pythagoras only for indirect 13.2 07 m horizontal measuring. For height measuring (vertical) it is more precise to use a function with the inclination measuring. Leica DISTO E7500 820692...
5.6 x 2.28 x 1.14 in Weight (with batteries) 198 g / 6.37 oz Temperature range: - Storage -25 to 70 °C -13 to 158 °F - Operation -10 to 50 °C 14 to 122 °F Leica DISTO E7500 820692...
Hold the instrument Warranty coverage for the entire usage time Heinrich-Wild-Strasse than 10° without any transverse tilt. of the product according to Leica Geosys- CH-9435 Heerbrugg Calibration mistake Make sure, the device is tems International Limited Warranty. Free of placed on a absolutely Internet: www.disto.com...
210 d’Industrie Canada. L’utilisation est • Consult the dealer or an experienced sujette aux deux conditions suivantes : radio/TV technician for help. • ce dispositif ne pas doit pas être la source d’interférences nuisibles, et Leica DISTO E7500 820692...
Looking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous. CAUTION Looking into the laser beam may be Subject to change (drawings, descriptions hazardous to the eyes. and technical data) without prior notice. Leica DISTO E7500 820692...
Page 26
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environ- mental Management Systems (ISO standard 14001). Copyright Leica Geosystems AG, Heerbrugg,...