Control Change Table - Yamaha M3000A Owner's Manual

(control change transmission/reception)
.........................oFF/GrP/on (Factory setting: on)
This specifies whether or not control change messages
will be transmitted and received via MIDI IN/OUT. If
this is set to " ," control change messages will not
be transmitted or received. If this is set to "
trol changes 1–104 received from an external device
will switch the corresponding channel on/off. (If mute
groups can be used, control changes 105–112 can also
be used to switch mute groups 1–8 on/off.) Also,
when the ON/EDIT switches of the M3000A are oper-
ated, the corresponding control change will be trans-
mitted. If this is set to "
numbers (105–112) which correspond to mute groups
will be transmitted.
(program change reception omni on/off)
............................... on/oFF (Factory setting: oFF)
This specifies whether or not the MIDI channel speci-
fied by the CH (MIDI channel) parameter will be
valid. When this setting is "
be received on all MIDI channels. When this setting is
" ," program changes will be received only on the
MIDI channel specified by the CH (MIDI channel)
parameter.
(echo back) ........ on/oFF (Factory setting: oFF)
When this parameter is "
MIDI IN connector will be retransmitted from the
MIDI OUT connector.
However if a bulk dump request is received, bulk
dump data will be output, and the bulk dump request
message itself will not be retransmitted (echoed).
(bulk out) ..................................... ALL/1–128
This operation transmits all scene memories (ALL) or
a specified scene memory (1–128) as MIDI bulk
dump data from the MIDI OUT connector. Select
" " or " " ~ " " and then press the STORE
switch to begin transmission. During transmission,
the display will indicate "
(bulk dump request) ..................... ALL/1–128
This operation transmits a request for a bulk dump
from the MIDI OUT connector. If the respective
MIDI IN/OUT connectors of two M3000A units are
connected, such a request will cause all scene memo-
ries (ALL) or the specified scene memory (1–128) of
the other M3000A to overwrite the scene memory (or
memories) of this M3000A. After selecting "
," press the STORE switch to transmit the
" " ~ "
bulk dump request MIDI message.
," con-
," only control change
," program changes will
," messages received at the
."
" or
About the Scene Memory function

Control change table

The following table shows the M3000A channel/bus
to which each control number is assigned. If the CC
(control change) item is turned ON in utility mode, a
control change message with a value of 64-127 will
turn on the corresponding channel/bus, and a control
change message with a value of 0-63 will turn it off. In
the same way, operating the ON/EDIT switches of the
M3000A will transmit the corresponding control
change message from the MIDI OUT connector.
Also, if mute groups can be used (refer to page 36),
control change numbers 105–112 can be used to
switch mute groups 1–8 on/off.
Control No. ON/EDIT Switch
0
1 CH INPUT 1
2 CH INPUT 2
3 CH INPUT 3
4 CH INPUT 4
5 CH INPUT 5
6 CH INPUT 6
7 CH INPUT 7
8 CH INPUT 8
9 CH INPUT 9
10 CH INPUT 10
11 CH INPUT 11
12 CH INPUT 12
13 CH INPUT 13
14 CH INPUT 14
15 CH INPUT 15
16 CH INPUT 16
17 CH INPUT 17
18 CH INPUT 18
19 CH INPUT 19
20 CH INPUT 20
21 CH INPUT 21
22 CH INPUT 22
23 CH INPUT 23
24 CH INPUT 24
25 CH INPUT 25
26 CH INPUT 26
27 CH INPUT 27
28 CH INPUT 28
29 CH INPUT 29
Control No. ON/EDIT Switch
30 CH INPUT 30
31 CH INPUT 31
32 CH INPUT 32
33 CH INPUT 33
34 CH INPUT 34
35 CH INPUT 35
36 CH INPUT 36
37 CH INPUT 37
38 CH INPUT 38
39 CH INPUT 39
40 CH INPUT 40
41 CH INPUT 41
42 CH INPUT 42
43 CH INPUT 43
44 CH INPUT 44
45 CH INPUT 45
46 CH INPUT 46
47 CH INPUT 47
48 CH INPUT 48
49 ST INPUT 1
50 ST INPUT 2
51 ST INPUT 3
52 ST INPUT 4
53 CH INPUT 49
54 CH INPUT 50
55 CH INPUT 51
56 CH INPUT 52
57 CH INPUT 53
58 CH INPUT 54
59 CH INPUT 55
35