Mix Section - Yamaha M3000A Owner's Manual

Control panel

Mix section

These output channels control the signals of MIX
buses 1–16. MIX buses 13/14 and 15/16 are controlled
as stereo pairs respectively. The signal that passes
through these output channels is output individually
from the MIX OUT 1–16 jacks (page 27), and can also
be sent to the MAS AFL bus, MAS PFL bus, ST bus,
and the matrix.
TO MATRIX TO MATRIX TO MATRIX
L R L R L R
PAN PAN PAN
L R L R L R
PAN PAN PAN
TO STEREO TO STEREO TO STEREO
MIX 1/2 MIX 3/4 MIX 5/6
CHECK CHECK CHECK
ON ON ON
ON/EDIT ON/EDIT ON/EDIT
10 10 10
5 5 5
0 0 0
5 5 5
10 10 10
20 20 20
40 40 40
AFL AFL AFL
MIX 1/2 MIX 3/4 MIX 5/6
A TO MATRIX switches
When these switches are on (
corresponding MIX OUT will be sent to the matrix.
B PAN controls/BAL controls
These controls specify the pan (MIX OUT 1–12) or
left/right balance (MIX OUT 13–16) when the MIX
OUT signal is sent to the ST bus.
C TO STEREO switches
When these switches are on (
corresponding MIX OUT will be sent to the ST bus.
14
TO MATRIX TO MATRIX TO MATRIX TO MATRIX
L R L R L R
PAN PAN PAN
L R L R L R L R
PAN PAN PAN BAL
TO STEREO TO STEREO TO STEREO TO STEREO
MIX 7/8 MIX 9/10 MIX 11/12 MIX 13/14
CHECK CHECK CHECK CHECK
ON ON ON ON
ON/EDIT ON/EDIT ON/EDIT ON/EDIT
10 10 10 10
5 5 5 5
0 0 0 0
5 5 5 5
10 10 10 10
20 20 20 20
40 40 40 40
AFL AFL AFL AFL
MIX 7/8 MIX 9/10 MIX 11/12 MIX 13/14
), the signal of the
), the signal of the
D ON/EDIT switches
The function of these switches and indicators will
depend on the mode of the M3000A.
In normal mode
The ON/EDIT switches will turn each MIX OUT on/
off. When on, the ON indicator will light. MIX OUTs
which are turned off will send no signal to the MIX
OUT 1–16 jacks, the MAS AFL bus, the ST bus or the
matrix. However even in this case, you can turn on the
AFL switch (6) to monitor the pre-fader signal from
the MONITOR OUT jacks or the PHONE jack.
A
TO MATRIX
In check mode
B
You can use the CHECK indicators to view the on/off
status of each MIX OUT stored in a scene before you
L R
BAL
C
actually recall the scene.
TO STEREO
In check mode, you can also use the ON/EDIT
switches to change only the lit/dark status of the
CHECK indicators. (The actual on/off setting will not
be affected.)
For details on check mode, refer to page 33.
MIX 15/16
E Mix master faders
CHECK
These faders adjust the output level of MIX OUT 1–
ON D
16. These faders affect the signal which is sent to the
ON/EDIT
MIX OUT 1–16 jacks, the MAS AFL bus, the ST bus,
10
and the matrix.
5
0
E
F AFL (after fader listen) switches
5
10
These switches allow the signals from MIX OUT to be
20
40
monitored from the MONITOR OUT jacks or
PHONES jack. When these switches are on (
indicator will light, and the pre-fader signal of the
F
corresponding MIX bus will be sent to the MAS PFL
AFL
MIX 15/16 bus, and the post-fader signal will be sent to the MAS
AFL bus, allowing you to monitor from the MONI-
TOR OUT jacks or the PHONES jacks. The signal of
the MAS AFL bus can be monitored when the MAS-
TER PFL switch (page 19) of the monitor section is
off, and the signal of the MAS PFL bus can be moni-
tored when this switch is on. However while even one
of the PFL switches of the input channels is on, the
signal of the PFL bus will take precedence, meaning
that it will not be possible to monitor MIX OUT.
), the