Page 2
DU8395Z Series DLP Projector - User Manual Index Preventing the Unauthorized Use of the Projector Using the Control Panel Lock Locking the control buttons Unlocking the control panel Copyright Using Security Lock Copyright Enable the Security Lock Disclaimer Unlocking the projector...
Page 3
DU8395Z Series DLP Projector - User Manual OSG Menu – ALIGNMENT Additional Information Lens Lock Product Specification Lens Control Supported Signal Input Timing Lens Type 2D formats Lens Memory Supported 3D Signal Center Lens Configurations of Terminals Digital Zoom DVI-D Terminal...
If the above scenario occurs, the user may be responsible to correcting the interference. WARNING WARNING! Changes or modifications without approval from Vivitek could void the user’s authorization to oper- ate the product. UM83950922EN01...
Page 6
(2) this device must accept any interference received, 的措施。 IEC/EN 60825-1:2014 including interference that may cause undesired operation. Model/Modèle/ ( 型號 / 型號 ) : DU8395Z-BK Warning ! Do not look into the beam. Complies with FDA performance standards for laser CAN ICES-3(A) /NMB-3(A)
DU8395Z Series DLP Projector - User Manual Installation and Use Notices 1. Read and keep this manual properly. 2. Pay attention to all the noted warnings, and follow all the guidelines and descriptions in this manual. 3. Do not use the projector near water.
The User’s Manual describes the installation, setup and operation of this projector and provides assistance to the in- stallation personnel and the end-user to fully develop the performance of the projector. VIVITEK has made every effort to ensure that the information in the Manual is correct at the time of printing. The contents may be frequently updated due to the continuously product improvement and customer feedback.
DU8395Z Series DLP Projector - User Manual Projector Overview Front-right View 1. Front IR Receiver The Receiver for IR signals from remote control. 2. LED Indicator Display current projector status such as power, light source status and warning. 3. Air Intake The fan pulls the cool air to the projector for system cooling.
Page 10
DU8395Z Series DLP Projector - User Manual Bottom View 15. Anti-thief Screw hole The anti-thief screw can be fastened to prevent Lens removing by unauthorized person. 16. Mounting Holes of Support Kit These two screws holes can be used to fix support kits of ultra-short throw lens.
Page 11
DU8395Z Series DLP Projector - User Manual IO Panel RS-232 B/Pb R/Pr MONITOR OUT TRIGGER SYNC WIRED REMOTE HDBaseT/LAN HDMI I DVI-D HDMI 2 TRIGGER(12V +/-1.5V) WIRED REMOTE When connected to the screen through a 3.5mm cable, Connect the supplied remote controller to the projector the screen deploys automatically on startup of the pro- jector.
DU8395Z Series DLP Projector - User Manual Control Panel ENGER POWER CENTER LENS User the button to turn on/off the projector. Push the button to center the lens and calibrate the pa- rameter of lens shift, focusing and zooming. INPUT Note Push the button to select the input signal.
DU8395Z Series DLP Projector - User Manual Remote Control Use the button to turn on the projector. Use the button to turn off the projector. FOCUS Adjust the focus of the projected image. ZOOM Zoom in/out the projected image. TEST PATTERN Use the button to show the test pattern.
Page 14
DU8395Z Series DLP Projector - User Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the re- mote will function well within a radius of about 10 meters (25 feet) and 15 degrees above or below the projector level.
DU8395Z Series DLP Projector - User Manual Installation and Setting up Inserting or Changing the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Place two AA batteries with the correct polarity.
DU8395Z Series DLP Projector - User Manual Installing the projector The high quality display effect can be guaranteed only when the projector is correctly installed. Generally, the light source facing the screen should be reduced or eliminated as much as possible. The contrast of the image will be obvi- ously reduced if the light directly shines on the screen, such as the beam from windows or the searchlight cast on the image.
DU8395Z Series DLP Projector - User Manual Mounting the projector For mounting the projector, please use UL Listed ceiling mounts and M4 screws, maximum depth of screw: 14 mm. UM83950922EN01...
DU8395Z Series DLP Projector - User Manual Installing or Removing the Optional Lens Caution • Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts. • When shipping the projector with the optional lens, remove the optional lens before shipping the projector. The lens and the lens shift mechanism may encounter damage caused by improper handling during transportation.
Page 19
DU8395Z Series DLP Projector - User Manual Removing the Existing Lens 5. Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be disengaged 6. Pull out the existing lens slowly. Caution •...
DU8395Z Series DLP Projector - User Manual Selecting the Input Voltage of AC Power There is one slide switch near AC switch, pleases switch it to corresponding input voltage of AC power. Please switch it to 115V if the input voltage range is 100V to 130V, switch to 230V if input voltage range is 200V to 240V.
DU8395Z Series DLP Projector - User Manual 3. The Power LED and LIGHT LED flashes green till power on process is finished. 4. After few seconds, both LEDs keep green, the projector is ready for use. Turning off the Projector Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector.
DU8395Z Series DLP Projector - User Manual Setting up the installation condition This projector is designed for set up in all angle including desktop, ceiling, portrait and free-tilt installation as below illustration. Please set the cooling condition according to the projector installation as below.
DU8395Z Series DLP Projector - User Manual Adjusting Projected Image Position This projector has the powered lens shift feature; the image can be shifted vertically or horizontally without moving the projector. The lens shift range is shown in the percentage of the screen height and width, the maximum vertical shift range can be up to 64% of the projected image height and down to 33% of the height, and maximum horizontal shift range is 24% of the image width to right, 14% of the image width to the left.
When the image is projected on a curved surface or screen at an angle, the image may become distorted. You can utilize the latest Vivitek Geometric Correction engine to make an image look visually correct when it is projected onto a non-planar screen or at an angle.
DU8395Z Series DLP Projector - User Manual Rotation After H or V Keystone is adjusted, Rotation option is available for rotating the image if required. The option is only available if H or V Keystone is adjusted, Use the ◄ or ► button to rotate the image clockwise or counterclockwise.
Page 26
DU8395Z Series DLP Projector - User Manual Keystone Example for using Horizontal Keystone. Rotation Example for using Rotation. Note • H or V Keystone is available when Horizontal or Vertical of Pincushion/Barrel is adjusted. • Rotation is available when H or V Keystone is adjusted.
Page 27
DU8395Z Series DLP Projector - User Manual Left 150 (+30 % ) -150 (-30%) Corner Adjustment In some applications, the distortion at the corner may occur due to the installation or projected surface. In this case, you can use Conner adjustment to correct the distortion corner by corner. Please refer to below illustra-...
Page 28
DU8395Z Series DLP Projector - User Manual Bottom Left Corner Horizontal -192 (Pixels) 192 (Pixels) Vertical -120 (Pixels) 120 (Pixels) Bottom Right Corner Horizontal -192 (Pixels) 192 (Pixels) Vertical -120 (Pixels) 120 (Pixels) UM83950922EN01...
DU8395Z Series DLP Projector - User Manual Preventing the Unauthorized Use of the Projector Using the Control Panel Lock This function allows you to lock control panel on the projector to prevent accidental presses by an individual or unau- thorized person to control the projector.
DU8395Z Series DLP Projector - User Manual Unlocking the control panel Once Control Panel Lock is enabled, all of control buttons on the projector are disabled. Please enter the OSD option CONTROL>OSD Settings>Control Panel Lock then select Off to unlock the control panel by remote control.
Page 31
DU8395Z Series DLP Projector - User Manual Security Lock is turned on, the pop-up message will be shown Lock as following, select OK to confirm or Cancel to ignore the setting. Security Lock Security Lock will be active in next power cycle, sure ?
DU8395Z Series DLP Projector - User Manual Using Control ID for Multi-projector Application When installing more than one projector in the room, the projectors may receive the remote control signal at the same time. In this case, you can use control ID function to specify the identification of the projector and remote control to operate the specified projector.
Page 33
DU8395Z Series DLP Projector - User Manual Step2: Set the identification number of remote control The remote control has 2 ways to operate the projector. • Use 1 remote control to operate 2 projector. Each remote control can record 2 ID control code. Press ID SET+MENU 5 seconds at the same time.
Page 34
DU8395Z Series DLP Projector - User Manual Checking the identification number of the projector and remote control The identification number of the projector and remote control can be checked by SERVICE menu as following figure, “X” represents that the function is not enabled; the number 26 is the current identification number of the remote con- trol.
DU8395Z Series DLP Projector - User Manual I/O - Connecting Follow the instructions below to connect projector to the video source, external control equipment (if any). When connecting to the equipment, use the correct signal cable to connect to the signal source and ensure that the cable is securely connected.
DU8395Z Series DLP Projector - User Manual Connecting to the Control Equipment The projector has the following control port for connecting to the control equipment. 3D sync signal transmitter(IR) RS-232 B/Pb R/Pr MONITOR OUT TRIGGER SYNC WIRED REMOTE HDBaseT/LAN HDMI I...
DU8395Z Series DLP Projector - User Manual Connecting to the Screen Trigger If your projection system includes the electric projection screen and other 12V trigger device, you can connect these devices to the 12V trigger to output and configure the output 12V signal settings. The projector will output 12V signals when it’s turned on.
DU8395Z Series DLP Projector - User Manual Connecting to external HDBaseT Transmitter The projector has a built-in HDBaseT receiver. With HDBaseT Transmitter (optional), the video, RS-232 and LAN signals can be sent to the projector via a single RJ-45 cable. If the HDBaseT Transmitter you purchased supports the input and output of the IR remote control, the control signals from the IR remote control can be sent to this projector via the RJ-45 cable.
DU8395Z Series DLP Projector - User Manual Using the projector Using On-Screen Display Using the OSD Menu The projector has an On-Screen Display (OSD) that lets you make image adjustments, change various settings and check current projector status. INPUT PICTURE...
Page 40
DU8395Z Series DLP Projector - User Manual Menu Tree Use the following table to quickly find a setting or determine the range for a setting. INPUT 2nd Layer 3rd Layer 4th Layer Selections Input Selection HDMI1 / HDMI2 / VGA / Component / BNC / DVI / 3G-SDI / HDBaseT...
Page 41
DU8395Z Series DLP Projector - User Manual ALIGNMENT 2nd Layer 3rd Layer 4th Layer Selections Lens Lock Off / On Lens Control Zoom / Focus / Shift control Lens Type non-UST Lens / UST Lens Memory1 Memory2 Memory3 Memory4 Memory5...
Page 42
DU8395Z Series DLP Projector - User Manual CONTROL 2nd Layer 3rd Layer Selections Language English / Français / Español / Deutsch / Português / 简体中文 / 繁體中文 / 日本語 / 한국어 Projection Mode Front Desktop / Front Ceiling / Rear Desktop / Rear Ceiling...
DU8395Z Series DLP Projector - User Manual OSD Menu – INPUT INPUT PICTURE ALIGNMENT CONTROL SERVICE Input Selection HDMI 2 HDMI 2 Auto Source < > Color Space < Auto > Aspect Ratio < Source > Overscan < > VGA Setup...
DU8395Z Series DLP Projector - User Manual This function allows you to split the screen for displaying the images from two input sources. PIP Option Enable PIP by choosing “ON”, and two windows will be shown on the projected picture. The larg- er one is the primary picture, the smaller one is the sub picture.
DU8395Z Series DLP Projector - User Manual Color Space This function allows you to change the corresponding color space for the input signal in most cases, the default is Auto. Auto The projector detects the input signal and switches to the corresponding color space automati- cally.
Page 46
DU8395Z Series DLP Projector - User Manual Eye Swap If the 3D image transmitted to the 3D glasses is reverse, you can set the Eye Swap to “Re- verse” to normalize the image. Otherwise, keeping mode of “Normal” would be suggested.
DU8395Z Series DLP Projector - User Manual OSD Menu – PICTURE INPUT PICTURE ALIGNMENT CONTROL SERVICE Picture Mode < High Bright > Brightness Contrast Saturation Sharpness Color Temperature < Native > Color Gamut Native Gamma Input Balance Noise Reduction Dynamic Black...
DU8395Z Series DLP Projector - User Manual Color Gamut (Цветовая гамма) Choose a different projection color display range. The available options are REC709 / EBU / SMPTE / Native (Родной). Gamma When the ambient light is so bright that may affect the projection of the details in the dim area of the image, you can change the gamma to adjust the chrominance.
DU8395Z Series DLP Projector - User Manual OSG Menu – ALIGNMENT INPUT PICTURE ALIGNMENT CONTROL SERVICE Lens Lock Lens Control Lens Type non-UST Lens Lens Memory Center Lens Digital Zoom Warp Blanking Edge Blend Screen Format 16:10 MENU = Back...
DU8395Z Series DLP Projector - User Manual • If using Ultra Short Throw Lens and setting to Non-UST Lens, the lens will be moved to the position which is lower than the default position of Ultra Short Throw Lens after performing Center Lens function, it causes the projected image is blocked by the top cover of the projector.
Page 51
DU8395Z Series DLP Projector - User Manual Warp This function is used to correct the distortion of image. Keystone Press ◄► to correct horizontal distortion or ▲▼ to correct vertical distortion. Refer to "Keystone on page24 " Rotation Press ◄► to correct incorrect angle of image. Refer to "Rotation on page25 ".
DU8395Z Series DLP Projector - User Manual Edge Blend Edge Blend function requires multiple projectors to simultaneously project on the same screen. Use this function to adjust the uniformity of image. To use this function, Edge Blending must be enabled on both projectors. The functions as follows can be only adjusted when Edge Blend is turned on.
DU8395Z Series DLP Projector - User Manual OSD Menu – CONTROL INPUT PICTURE ALIGNMENT CONTROL SERVICE Language English Projection Mode Front Desktop High Altitude Auto Auto Power Off < > Auto Power On < > Network Light Power Background Black Startup Logo <...
Page 54
DU8395Z Series DLP Projector - User Manual Note • Estimate Altitude is calculated by atmosphere pressure, it may have the tolerance comparing to actual altitude. • If any over temperature or system protection message, please adjust High Altitude by Manual.
DU8395Z Series DLP Projector - User Manual Light Power Use ◄ ►button to select the power save mode (Eco), normal (Normal) or custom power level. Light Power ECO : Projection operates in the energy-saving mode, which is equivalent to 80 % power of light source.
DU8395Z Series DLP Projector - User Manual Trigger The projector is provided with a set of trigger output. User can connect the trigger to the screen with projector by the cable. If user does so, once the projector is powered, the screen would be automatically turned on as well. There is a 2-3 second delay to activate this function.
DU8395Z Series DLP Projector - User Manual OSD Menu – SERVICE INPUT PICTURE ALIGNMENT CONTROL SERVICE Model DU8395Z Serial Number C847XXXXX01558 Software Version 1 ME03-SE01-FE06t2 Software Version 2 LE04-2-RE01-3140 Control / Remote ID Active Source HDMI2 Signal Format No source...
DU8395Z Series DLP Projector - User Manual Additional Information Product Specification Display Type Single Chip 0.67" DLP Technology Brightness*** 15,000 Lumens Native Resolution WUXGA (1920 x 1200) Maximum Resolution WUXGA (1920 x 1200)@60Hz (Reduced Blanking) Contrast Ratio 100,000:1 (Full On/Full Off)
DU8395Z Series DLP Projector - User Manual Screen Trigger Wired Remote Tip Sleeve Tip Sleeve Sleeve Sleeve Ring Ring Ring Ring VCC(12V) VCC(3.3V) Sleeve- Ground Sleeve- Ground Ring Signal Ring Signal HDBaseT/LAN Terminal 3D Sync Out 8 7 6 5 4 3 2 1...
DU8395Z Series DLP Projector - User Manual Lens Series Eight types of optional electric lenses are available for the projector as below table. Contact the authorized dealer of Vivitek for details. Part Number Lens Name F Number Focal Length Zoom Ratio...
DU8395Z Series DLP Projector - User Manual LED Indication Several indicators messages are used to display the current projector status or alert the abnormal message. POWER LED Indicator LED Color and Status Pattern Sequence Condition Description Off (No color) AC Power is off GREEN, continuous flashing.
DU8395Z Series DLP Projector - User Manual Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem re- mains unsolved, contact your dealer for assistance. Often the problem is something as simple as a loose connection. Check the following before proceeding to the prob- lem-specific solutions.
DU8395Z Series DLP Projector - User Manual Problem: The color of the projected image does not match the source image. Adjust the Color temperature and Gamma settings on the PICTURE menu of the OSD Projection Problems Problem: There is no light from the projector 1.
DU8395Z Series DLP Projector - User Manual About the Vivitek Support If you cannot find solutions from this user guideline, please contact us using the contact information below: North America Vivitek Service Center Tel: 855-885-2378 (Toll-Free) 15700 Don Julian Road, Suite B Email: T.services1@vivitekcorp.com...