Advertisement
Quick Links
24" A
**T
HESE MODELS ARE FIELD CONVERITBLE FOR
**T
HESE MODELS ARE FIELD CONVERTIBLE FOR
I
F YOU HAVE QUESTIONS
I
NSTALLATION
P
ROFESSIONAL
G
, C
LL
AS
ONVECTION WITH
24" N
ATURAL
*TN480-7BW
24" LP/P
ROPANE
*PN480-7BW
,
800-251-7224, 8
CALL
,
.F
WEBSITE
WWW
I
NSTRUCTIONS
R
M
ANGE
ODELS
O
B
PEN
URNERS
G
M
AS
ODEL
LP/P
G
M
AS
ODEL
N
ATURAL GAS
5
E
AM TO
PM
ASTERN
S
R
.
IVE
TAR
ANGE
COM
**
.**
ROPANE GAS
.**
T
,
IME
OR VISIT OUR
.
Advertisement
Related Manuals for FiveStar TPN4807BW
Summary of Contents for FiveStar TPN4807BW
- Page 1 NSTALLATION NSTRUCTIONS ROFESSIONAL ANGE ODELS 24” A ONVECTION WITH URNERS 24” N ATURAL ODEL *TN480-7BW LP/P HESE MODELS ARE FIELD CONVERITBLE FOR ROPANE GAS 24” LP/P ROPANE ODEL *PN480-7BW HESE MODELS ARE FIELD CONVERTIBLE FOR ATURAL GAS 800-251-7224, 8 F YOU HAVE QUESTIONS CALL AM TO ASTERN...
- Page 2 Be sure to leave these instructions with the Consumer. Hoods should be 24" min. deep and at least the same width as the cooktop. FiveStar hoods may be installed from 24” to 30” above the Note to Consumer • Keep these instructions for future cooking surface.
- Page 3 NSTALLATION NSTRUCTIONS Please read these instructions before attempting to install this range Inspection and Unpacking Check the range carton for visible damage. If there is damage or even creases in the carton, contact the carrier, request an inspection and file the appropriate freight claim.
-
Page 4: Remove Packaging
STEP 1 REMOVE PACKAGING Before moving the range indoors: Remove outer carton and packing material from the shipping base. The range is now ready for removal from the wooden base. STEP 2 Due to the weight of these ranges, use a dolly with soft wheels to move this range. -
Page 5: Electric Connection
ELECTRIC CONNECTION This range must be supplied with 120 volt, 60 Hz. and connected to an individual, properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse. The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong grounding wall receptacle to minimize the possibility of shock hazard from this... -
Page 7: Connecting The Range To Gas
STEP 7 CONNECTING THE RANGE TO GAS Because hard piping restricts When using test pressures greater movement of the range, the use of an than ½ psig to pressure test the gas A.G.A. certified flexible metal supply system of the residence, appliance connector is recommended disconnect the range and individual unless local codes require a hard-... -
Page 8: Level The Range
STEP 8 LEVEL THE RANGE 1. Remove shipping tape from the leveling legs. 2. Carefully slide the range into position. Be careful not to damage the floor or entangle power cord and gas flexible tubing. 3. To adjust leveling legs, turn counter- clockwise to raise the range;... - Page 10 STEP 11 ASSEMBLE SURFACE BURNER COMPONENTS • Remove shipping screw from each surface burner. • Remove each surface burner. • Place drip pan in position under each burner. Locate “dimples”. • Re-install surface burners. • Install burner pans. • Install burner grates. STEP 12 SURFACE BURNER OPERATION OPEN SURFACE BURNERS...
- Page 11 STEP 15 CHECKLIST FOR OPEN BURNER INSTALLATION MAKE SURE ALL CONTROLS ARE IN THE “OFF” POSITION. Gas supply is “on” Electric power is “on” Burner drip pans in position under burners Surface burners in position Burner pans in positions Burner grates in position Oven and broiler racks installed Surface burner ignition test Gas oven ignition test...