Related Manuals for ASROCK EP2C622D24LM
Summary of Contents for ASROCK EP2C622D24LM
- Page 1 EP2C622D24LM EP2C621D24LM-AB User Manual Version 1.0 Published March 2018 Copyright©2018 ASRock Rack INC. All rights reserved.
- Page 2 In no event shall ASRock Rack, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock Rack has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
- Page 3 Contact Information If you need to contact ASRock Rack or want to know more about ASRock Rack, you’re welcome to visit ASRock Rack’s website at www.ASRockRack.com; or you may contact your dealer for further information. ASRock Rack Incorporation 6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,...
-
Page 4: Table Of Contents
Contents Chapter 1 Introduction Package Contents Specifications Unique Features Motherboard Layout Onboard LED Indicators I/O Panel Block Diagram Chapter 2 Installation Screw Holes Pre-installation Precautions Installing the CPU and Heatsink Installation of Memory Modules (DIMM) Expansion Slots (PCI Express Slots) Jumper Setup Onboard Headers and Connectors Unit Identification purpose LED/Switch... - Page 5 Main Screen Advanced Screen 3.3.1 CPU Configuration 3.3.2 DRAM Configuration 3.3.3 Chipset Configuration 3.3.4 Storage Configuration 3.3.5 ACPI Configuration 3.3.6 USB Configuration 3.3.7 Super IO Configuration 3.3.8 Serial Port Console Redirection 3.3.9 H/W Monitor 3.3.10 Runtime Error Logging 3.3.11 Intel SPS Configuration 3.3.12 Intel®...
- Page 6 Exit Screen Chapter 4 Software Support Install Operating System Support CD Information 4.2.1 Running The Support CD 4.2.2 Drivers Menu 4.2.3 Utilities Menu 4.2.4 Contact Information Chapter 5 Troubleshooting Troubleshooting Procedures Technical Support Procedures Returning Merchandise for Service Appendix A Mezzanine Card Support List...
-
Page 7: Chapter 1 Introduction
In case any modifications of this manual occur, the updated version will be available on ASRock Rack website without further notice. You may find the latest memory and CPU support lists on ASRock Rack website as well. ASRock Rack’s Website: www.ASRockRack.com If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. -
Page 8: Specifications
1.2 Specifications EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB MB Physical Status Form Factor L shape Dimension 16.7" x 17"(42.4 cm x 43.2 cm) Processor System Intel® Xeon® Scalable Processor Socket Dual Socket P, LGA3647 Chipset EP2C626D24LM: Intel® C626 EP2C622D24LM: Intel® C622 EP2C621D24LM-AB: Intel®... - Page 9 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB IPMI Dedicated 1 x Realtek RTL8211E for dedicated management GLAN GLAN Features - Watch Dog - NMI Graphics Controller ASPEED AST2500 VRAM DDR4 16MB Rear Panel I/O VGA Port 1 (D-sub) USB 3.0 Port LAN Port...
- Page 10 - CPU/Front Fan Tachometer - CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature) - CPU/Front Fan Multi-Speed Control Voltage Voltage Monitoring: +12V, +5V, +3V, BAT, 1.8V_PCH, 1.05V_ PCH, PVNN_PCH, VCCM_ABC, VCCM_DEF, VCCM_ GHI, VCCM_JKL, CPU1_VCORE, CPU2_VCORE, +5VSB, +3VSB Support OS Microsoft®...
-
Page 11: Unique Features
POST or the <F2> key to enter into the BIOS setup menu to access ASRock Rack Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. -
Page 12: Motherboard Layout
1.4 Motherboard Layout EP2C626D24LM / EP2C622D24LM 43.18cm (17 in) HSBP_CPU2_1 RAID_1 IPMB_1 BMC_SMB_1 BMC_SMB_3 HDD_PWR1 HSBP_PWR1 BMC_SMB_2 DDR4_I1 (64 bit, 288-pin module, Blue) DDR4_I2 (64 bit, 288-pin module, White DDR4_H1 (64 bit, 288-pin module, Blue) DDR4_H2 (64 bit, 288-pin module, White) - Page 13 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Description PSU Connector 2 (PSU_CON2) PSU Connector 1 (PSU_CON1) HDD Power Connetor (HDD_PWR1) Backplane Power Connector (HSBP_PWR1) Virtual RAID On CPU Header (RAID_1) BMC SMBus Header 1 (BMC_SMB_1) BMC SMBus Header 2 (BMC_SMB_2) BMC SMBus Header 3 (BMC_SMB_3)
- Page 14 6No. Description USB 2.0 Header (USB_1_2) M.2 Socket (M2_1) (Type 2230/2242/2260/2280) ESPI / LPC Switch Jumper (ESPI_LPC_SW1) Front LAN LED Header (FRONT_LED_LAN34) PMBUS Mode Jumper (PMBUS_SEL_CLK1) PMBUS Mode Jumper (PMBUS_SEL_ALT1) PMBUS Mode Jumper (PMBUS_SEL_DAT1) Chassis ID2 Jumper (CHASSIS_ID2) Chassis ID1 Jumper (CHASSIS_ID1) Non Maskable Interrupt Button (NMI_BTN1) Chassis ID0 Jumper (CHASSIS_ID0) NCSI Mode Jumper (NCSI_SEL1)
- Page 15 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB * For DIMM installation and configuration instructions, please see p.18 (Installation of Memory Modules (DIMM)) for more details. ** The first “S“ of the “SSATA” means “secondary”. SATA is managed by the first controller. SSATA is managed by the secondary controller.
- Page 16 EP2C621D24LM-AB 43.18cm (17 in) HSBP_CPU2_1 RAID_1 IPMB_1 BMC_SMB_1 BMC_SMB_3 HDD_PWR1 HSBP_PWR1 BMC_SMB_2 DDR4_I1 (64 bit, 288-pin module, Blue) DDR4_I2 (64 bit, 288-pin module, White DDR4_H1 (64 bit, 288-pin module, Blue) DDR4_H2 (64 bit, 288-pin module, White) DDR4_G1 (64 bit, 288-pin module, Blue) DDR4_G2 (64 bit, 288-pin module, White...
- Page 17 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Description PSU Connector 2 (PSU_CON2) PSU Connector 1 (PSU_CON1) HDD Power Connetor (HDD_PWR1) Backplane Power Connector (HSBP_PWR1) Virtual RAID On CPU Header (RAID_1) BMC SMBus Header 1 (BMC_SMB_1) BMC SMBus Header 2 (BMC_SMB_2) BMC SMBus Header 3 (BMC_SMB_3)
- Page 18 6No. Description USB 2.0 Header (USB2_1_2) M.2 Socket (M2_1) (Type 2230/2242/2260/2280) ESPI / LPC Switch Jumper (ESPI_LPC_SW1) Front LAN LED Header (FRONT_LED_LAN34) PMBUS Mode Jumper (PMBUS_SEL_CLK1) PMBUS Mode Jumper (PMBUS_SEL_ALT1) PMBUS Mode Jumper (PMBUS_SEL_DAT1) Chassis ID2 Jumper (CHASSIS_ID2) Chassis ID1 Jumper (CHASSIS_ID1) Non Maskable Interrupt Button (NMI_BTN1) Chassis ID0 Jumper (CHASSIS_ID0) NCSI Mode Jumper (NCSI_SEL1)
- Page 19 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB * For DIMM installation and configuration instructions, please see p.22 (Installation of Memory Modules (DIMM)) for more details. ** The first “S“ of the “SSATA” means “secondary”. SATA is managed by the first controller. SSATA is managed by the secondary controller.
-
Page 20: Onboard Led Indicators
1.5 Onboard LED Indicators DDR4_I1 (64 bit, 288-pin module, Blue) DDR4_I2 (64 bit, 288-pin module, White DDR4_H1 (64 bit, 288-pin module, Blue) DDR4_H2 (64 bit, 288-pin module, White) DDR4_G1 (64 bit, 288-pin module, Blue) DDR4_G2 (64 bit, 288-pin module, White FRNT_FAN4 CPU2 CPU2_FAN1... -
Page 21: I/O Panel
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 1.6 I/O Panel No. Description No. Description IPMI LAN Header (IPMI1) UID Switch (UID) USB 3.0 Port (USB3_1) VGA Header (VGA1) USB 3.0 Port (USB3_2) Serial Port (COM1) LAN Port LED Indications *There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications. -
Page 22: Block Diagram
1.7 Block Diagram EP2C626D24LM / EP2C622D24LM... - Page 23 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB EP2C621D24LM-AB NCSI PCIe Gen2 x1 PCIe x16 Gen3 Port:2A-2D USB2.0 x2 DMI3 x4...
-
Page 24: Chapter 2 Installation
Chapter 2 Installation This is a L-shape form factor (16.7’’ x 17’’, 42.42 cm x 43.2 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. EP2C622/EP2C621 Series are dual socket motherboards that support Intel® Xeon® Scalable Processors. -
Page 25: Installing The Cpu And Heatsink
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 2.3 Installing the CPU and Heatsink 1. Before you insert the CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. - Page 26 1. Before you installed the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. 2. Illustration in this documentation are examples only. Heatsink or fan cooler type may differ.
- Page 27 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB...
- Page 28 Tighten the two Corner Plunger to 12 IN.LB. Two turns at a time. Tighten the two Middle Nuts to 12 IN.LB. Two turns at a time.
-
Page 29: Installation Of Memory Modules (Dimm)
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 2.4 Installation of Memory Modules (DIMM) This motherboard provides twenty-four 288-pin DDR4 (Double Data Rate 4) DIMM slots in two groups, and supports Quad Channel Memory Technology. CPU1 CPU2 DDR4_A1, B1, C1, D1, E1, F1 (Blue) - Page 30 2 CPU Configurations DIMM(S) CPU1 CPU2 The symbol # indicates the slot is populated.
- Page 31 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB...
-
Page 32: Expansion Slots (Pci Express Slots)
2.5 Expansion Slots (PCI Express Slots) There are 3 PCI Express slots on this motherboard. PCIE slots: PCIE1 (PCIE 3.0 x16 slot, from CPU1) is used for PCI Express x16 lane width cards. PCIE2 (PCIE 3.0 x16 slot, from CPU2) is used for PCI Express x16 lane width cards. PCIE3 (PCIE 3.0 x8 slot, from CPU2) is used for PCI Express x8 lane width cards. -
Page 33: Jumper Setup
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 2.6 Jumper Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”... - Page 34 PMBUS Mode Jumpers (3-pin PMBUS_SEL_CLK1) (3-pin PMBUS_SEL_DAT1) PMBus connected to BMC PMBus connected to PCH (3-pin PMBUS_SEL_ALT1) (Default) SATA DOM Power Jumper (3-pin SATAPWR1) SATA DOM (SSATA_1) SATA DOM (SSATA_1) requires 5V power supply does NOT require 5V power supply (Default) SATA DOM Power Jumper (3-pin SATAPWR2) SATA DOM (SSATA_0)
- Page 35 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Chassis ID0 Jumper (3-pin CHASSIS_ID0) Chassis ID1 Jumper (3-pin CHASSIS_ID1) Chassis ID2 Jumper (3-pin CHASSIS_ID2) Board Level SKU (Default) Reserved for system level Chassis ID0 Jumper (3-pin CHASSIS_ID0) Chassis ID1 Jumper (3-pin CHASSIS_ID1) Chassis ID2 Jumper...
-
Page 36: Onboard Headers And Connectors
2.7 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard. System Panel Header C onnec t t he power sw itch, PLED+ PLED-... - Page 37 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Auxiliary Panel Header This header supports multiple (18-pin AUX_PANEL1) functions on the front panel, including front panel SMB, internet status indicator. A. Front panel SMBus connecting pin (6-1 pin FPSMB) This header allows you to connect SMBus (System Management Bus) equipment. It can be used for communication between peripheral equipment in the system, which has slower transmission rates, and power management equipment.
- Page 38 Serial ATA3 DOM The SATA3 DOM connector s Connectors support both a SATA DOM (SSATA_0) (Disk-On-Module) and a SATA SSATA_0 SSATA_1 (SSATA_1) data cable for internal storage device. *SSATA_0 is shared with the M.2 slot (M2_1) . When SSATA_0 is populated with a SATADOM module, M2_1 slot is disabled.
- Page 39 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB USB_PWR USB 2.0 Header There is one USB 2.0 header on (19-pin USB_1_2) this motherboard. This USB 2.0 DUMMY header can support two USB 2.0 ports. USB_PWR Backplane PCI Express These headers are used for the...
- Page 40 EP2C626D24LM / Please connect system fans to EP2C622D24LM: the fan connectors. System Fan Connectors (6-pin SYS_FAN1) (see p.6, No. 26) (6-pin SYS_FAN2) (see p.6, No. 23) (6-pin SYS_FAN3) (see p.6, No. 21) (6-pin SYS_FAN4) (see p.6, No. 18) (6-pin SYS_FAN5) (see p.6, No.
- Page 41 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Front VGA Header Please connect either end of (15-pin VGA1) VGA cable to VGA header. Virtual RAID On CPU This connector supports Intel® Header Virtual RAID on CPU and VROC RAID KEY (4-pin RAID_1) NVME/AHCI RAID on CPU +3VSB PCIE.
- Page 42 IPMB_SDA Intelligent Platform This 4-pin connector is used IPMB_SCL Management Bus header to provide a cabled baseboard (4-pin IPMB_1) or front panel connection for value added features and 3rd- No Connect party add-in cards, such as Emergency Management cards, that provide management features using the IPMB.
-
Page 43: Unit Identification Purpose Led/Switch
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 2.8 Unit Identification purpose LED/Switch With the UID button, You are able to locate the server you’re working on from behind a rack of servers. Unit Identification When the UID button on the purpose LED/Switch... -
Page 44: M.2_Ssd (Ngff) Module Installation Guide
2.10 M.2_SSD (NGFF) Module Installation Guide The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The M.2_SSD (NGFF) Socket 3 can accommodate either a M.2 SATA3 6.0 Gb/s module or a M.2 PCI Express module up to Gen 3 x2 (10Gb/s). - Page 45 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Step 3 Move the standoff based on the module type and length. The standoff is placed at the nut location D by default. Skip Step 3 and 4 and go straight to Step 5 if you are going to use the default nut.
-
Page 46: Chapter 3 Uefi Setup Utility
Chapter 3 UEFI Setup Utility 3.1 Introduction Th is section explains how to use the UEFI SETUP UTILITY to confi gure your system. Th e UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer. -
Page 47: Navigation Keys
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items... -
Page 48: Main Screen
3.2 Main Screen Once you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview. The Main screen provides system overview information and allows you to set the system time and date. -
Page 49: Advanced Screen
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3 Advanced Screen In this section, you may set the configurations for the following items: CPU Configuration, DRAM Configuration, Chipset Configuration, Storage Configuration, ACPI Configura- tion, USB Configuration, Super IO Configuration, Serial Port Console Redirection, H/ W Monitor, Runtime Error Logging, Intel SPS Configuration, Intel(R) VMD Technology, Intel(R) Virtual RAID on CPU and Instant Flash. -
Page 50: Cpu Configuration
3.3.1 CPU Configuration Intel SpeedStep Technology Intel SpeedStep technology allows processors to switch between multiple frequencies and voltage points for better power saving and heat dissipation. CPU turbo ratio can be fixed when Intel SpeedStep Technology set Disabled and Intel Turbo Boost Technology set En- abled. - Page 51 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Limit is exceeded. Short Duration Power Limit Configure Package Power Limit 2 in watts. When the limit is exceeded, the CPU ratio will be lowered immediately. A lower limit can protect the CPU and save power, while a higher limit may improve performance.
- Page 52 Package C State Support Enable CPU, PCIe, Memory, Graphics C State Support for power saving. CPU C6 State Support Enable C6 deep sleep state for lower power consumption. Enhanced Halt State(C1E) Enable Enhanced Halt State (C1E) for lower power consumption. Hardware P-States Disable: Hardware chooses a P-state based on OS Request (Legacy P-States) Native Mode: Hardware chooses a P-state based on OS guidance...
-
Page 53: Dram Configuration
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.2 DRAM Configuration Enforce POR Enable to enforce POR restrictions for DDR4 frequency and voltage programming. DRAM Frequency If [Auto] is selected, the motherboard will detect the memory module(s) inserted and assign the appropriate frequency automatically. - Page 54 Memory Rank Sparing Enable or disable Memory Rank Sparing.
-
Page 55: Chipset Configuration
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.3 Chipset Configuration MMCFG Base Use this item to select MMCFG Base. MMIO High Base Use this item to select MMIO High Base. MMIO High Size Use this item to select MMIO High Size. Above 4G Decoding Enable or disable 64bit capable Devices to be decoded in Above 4G Address Space (only if the system supports 64 bit PCI decoding). - Page 56 MEZZ_C1 (for EP2C622D24LM only) This allows you to enable or disable MEZZ Type-C. VT-d Intel Virtualization Technology for Directed I/O helps your virtual machine monitor bet- ter utilize hardware by improving application compatibility and reliability, and providing additional levels of manageability, security, isolation, and I/O performance.
- Page 57 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB MEZZ_MB_C1 Link Speed This allows you to select PCIE Link Speed. MEZZ_MB_C1 ASPM Support This option enables or disables the ASPM support for all CPU downstream devices. MEZZ_MB_A2_B2 Link Speed This allows you to select PCIE Link Speed.
-
Page 58: Storage Configuration
3.3.4 Storage Configuration Hard Disk S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled] and [Enabled]. SATA Controller Use this item to enable or disable SATA Controllers. SATA Mode Selection Identify the SATA port is connected to Solid State Drive or Hard Disk Drive. - Page 59 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB SSATA ALPM Use this item to enable or disable SALP.
-
Page 60: Acpi Configuration
3.3.5 ACPI Configuration PCIE Devices Power On Use this item to enable or disable PCIE devices to turn on the system from the power-soft- off mode. Ring-In Power On Use this item to enable or disable Ring-In signals to turn on the system from the power- soft-off mode. -
Page 61: Usb Configuration
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.6 USB Configuration Legacy USB Support Use this option to enable or disable legacy support for USB devices. The default value is [Enabled]. -
Page 62: Super Io Configuration
3.3.7 Super IO Configuration Serial Port 1 Configuration Use this item to set parameters of Serial Port 1 (COM1). Serial Port Use this item to enable or disable the serial port. Change Settings Use this item to select an optimal setting for Super IO device. SOL Configuration Use this item to set SOL configuration. -
Page 63: Serial Port Console Redirection
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.8 Serial Port Console Redirection COM1 Console Redirection Use this option to enable or disable Console Redirection. If this item is set to Enabled, you can select a COM Port to be used for Console Redirection. - Page 64 Bits Per Second Use this item to select the serial port transmission speed. The speed used in the host computer and the client computer must be the same. Long or noisy lines may require lower transmission speed. The options include [9600], [19200], [38400], [57600] and [115200]. Data Bits Use this item to set the data transmission size.
- Page 65 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB computer and the host computer to which you are connected exchange information. Legacy Serial Redirection Port Use this item to select a COM port to display redirection of Legacy OS and Legacy OPROM Messages. Serial Port for Out-of-Band Management/Windows Emergency...
-
Page 66: H/W Monitor
3.3.9 H/W Monitor In this section, it allows you to monitor the status of the hardware on your system, includ- ing the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage. Fan Control If [Auto] is selected, the fan speed will controlled by BMC. - Page 67 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB FRNT_FAN 4 This allows you to set the front fan 4’s speed. The default value is [Smart Fan]. Smart Fan Control This allows you to set the Smart fan’s level speed. Smart Fan Duty Control Smart Fan Duty x (x means 1 to 11 stage) This allows you to set duty cycle for each stage.
-
Page 68: Runtime Error Logging
3.3.10 Runtime Error Logging WHEA Support Use this item to enable or disable Windows Hardware Error Architecture. System Error Use this item to enable or disable System Error feature. When it is set to [Enabled], you can configure Memory Error and PCIE Error log features. S/W Error Injection Support When it is set to [Enabled], S/W Error Injection is supported by unlocking MSR Ox790. - Page 69 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB PCIE Uncorrected Error Enable Use this item to enable or disable PCIe Uncorrectable errors. PCIE Fatal Error Enable Use this item to enable or disable PCIe Ftal errors.
-
Page 70: Intel Sps Configuration
3.3.11 Intel SPS Configuration ME Subsystem screen displays the Intel ME Subsystem Configuration information, such as Operational Firmware Version and Firmware State. -
Page 71: Intel® Vmd Technology
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.12 Intel® VMD technology ® Press <Enter> to bring up the Intel VMD for Volume Management Device Configuration menu. ® Intel VMD for Volume Management Device on Socket0 ® Intel VMD for Volume Management Device Technology Use this item to enable or disable Intel(R) Volume Management Device Technology in this Stack. - Page 72 VMD port 3D Use this item to enable or disable Intel(R) Volume Management Device Technology on specific root port. Hot Plug Capable Use this item to enable or disable Hot Plug for PCIe Root Ports 3A-3D. ® Intel VMD for Volume Management Device on Socket1 ®...
- Page 73 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB specific root port. VMD port 3B Use this item to enable or disable Intel(R) Volume Management Device Technology on specific root port. VMD port 3C Use this item to enable or disable Intel(R) Volume Management Device Technology on specific root port.
-
Page 74: Intel® Virtual Raid On Cpu
3.3.13 Intel® Virtual RAID on CPU Intel VROC Managed Volumes (Available after the RAID has been created.) Select to see more information about the RAID Volume. All Intel VMD Controllers Select to see more information about the Intel VMD Controllers. - Page 75 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Create RAID Volume This page allows you to create a RAID volume. Non-RAID Physical Disks (Available when no RAID is created.) Select to see more information about the disk. RAID Volumes (Available after the RAID has been created.) Select to see more information about the RAID Volume.
- Page 76 Name Enter an unique volume name that has no special characters and is 16 charaters or less. RAID Level Select RAID Level. Enable RAID spanned over VMD Controllers Select [X] to enable RAID spanned over VMD Controllers. Select Disks Select [X] to select disks. Strip Size Select strip size.
-
Page 77: Instant Flash
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.3.14 Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM. This convenient UEFI update tool allows you to update system UEFI without entering operating systems ® first like MS-DOS or Windows . -
Page 78: Security
3.4 Security In this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it. Supervisor Password Set or change the password for the administrator account. Only the administrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password. -
Page 79: Key Management
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.4.1 Key Management In this section, expert users can modify Secure Boot Policy variables without full authenti- cation. Provision Factory Defaults Allow to provision factory default Secure Boot keys when System is in Setup Mode. - Page 80 d) EFI_CERT_SHA256, 384, 512 2. Authenticated UEFI Variable 3. EFI PE/COFF Image(SHA256) Key Source: Default, External, Mixed, Test Key Exchange Keys Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate in: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER encoded) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHA256, 384, 512 2.
- Page 81 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER encoded) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHA256, 384, 512 2. Authenticated UEFI Variable 3. EFI PE/COFF Image(SHA256) Key Source: Default, External, Mixed, Test Authorized TimeStamps Enroll Factory Defaults or load certificates from a file: 1.
-
Page 82: Boot Screen
3.5 Boot Screen In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. Boot Option #1 Use this item to set the system boot order. Boot Option Filter This option controls Legacy/UEFI ROMs priority. - Page 83 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB AddOn ROM Display Use this option to adjust AddOn ROM Display. If you enable the option “Full Screen Logo” but you want to see the AddOn ROM information when the system boots, please select [Enabled]. Configuration options: [Enabled] and [Disabled]. The default value is [Enabled].
-
Page 84: Csm Parameters
3.5.1 CSM Parameters Enable to launch the Compatibility Support Module. Please do not disable unless you’re running a WHCK test. If you are using Windows 10 64-bit and all of your devices support UEFI, you may also disable CSM for faster boot speed. Launch Other Storage OpROM Policy Select UEFI only to run those that support UEFI option ROM only. - Page 85 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB CPU2_PCIE2 Slot OpROM This option controls Legacy/UEFI ROMs priority. MEZZ_A1_B1 Slot OpROM This option controls Legacy/UEFI ROMs priority. MEZZ_C1 Slot OpROM (for EP2C622D24LM only) This option controls Legacy/UEFI ROMs priority. MEZZ_A2_B2 Slot OpROM This option controls Legacy/UEFI ROMs priority.
-
Page 86: Event Logs
3.6 Event Logs Change Smbios Event Log Settings This allows you to configure the Smbios Event Log Settings. When entering the item, you will see the followings: Smbios Event Log Use this item to enable or disable all features of the SMBIOS Event Logging during system boot. - Page 87 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB entries which utilize a multiple-event counter. The value ranges from 0 to 99 minutes. View Smbios Event Log Press <Enter> to view the Smbios Event Log records. All values changed here do not take effect until computer is restarted.
-
Page 88: Server Mgmt
3.7 Server Mgmt Wait For BMC Wait For BMC response for specified time out. In PILOTII, BMC starts at the same time when BIOS starts during AC power ON. It takes around 30 seconds to initialize Host to BMC interfaces. -
Page 89: System Event Log
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB 3.7.1 System Event Log SEL Components Change this to enable ro disable all features of System Event Logging during boot. Erase SEL Use this to choose options for earsing SEL. When SEL is Full Use this to choose options for reactions to a full SEL. -
Page 90: Bmc Network Configuration
3.7.2 BMC Network Configuration Lan Channel (Failover) Manual Setting IPMI LAN If [No] is selected, the IP address is assigned by DHCP. If you prefer using a static IP address, toggle to [Yes], and the changes take effect after the system reboots. The default value is [No]. - Page 91 EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB The default login information for the IPMI web interface is: Username: admin Password: admin For more instructions on how to set up remote control environment and use the IPMI man- agement platform, please refer to the IPMI Configuration User Guide or go to the Support...
-
Page 92: Exit Screen
3.8 Exit Screen Save Changes and Exit When you select this option, the following message “Save configuration changes and exit setup?” will pop-out. Press <F10> key or select [Yes] to save the changes and exit the UEFI SETUP UTILITY. Discard Changes and Exit When you select this option, the following message “Discard changes and exit setup?”... -
Page 93: Chapter 4 Software Support
4.2.4 Contact Information If you need to contact ASRock Rack or want to know more about ASRock Rack, welcome to visit ASRock Rack’s website at http://www.ASRockRack.com; or you may contact your... -
Page 94: Chapter 5 Troubleshooting
Chapter 5 Troubleshooting 5.1 Troubleshooting Procedures Follow the procedures below to troubleshoot your system. Always unplug the power cord before adding, removing or changing any hardware com- ponents. Failure to do so may cause physical injuries to you and damages to motherboard components. - Page 95 1. Verify if the battery on the motherboard provides ~3VDC. Install a new battery if it does not. 2. Confirm whether your power supply provides adaquate and stable power. Other problems... 1. Try searching keywords related to your problem on ASRock Rack’s FAQ page: http://www.asrockrack.com/support...
-
Page 96: Technical Support Procedures
5.2 Technical Support Procedures If you have tried the troubleshooting procedures mentioned above and the problems are still unsolved, please contact ASRock Rack’s technical support with the following information: 1. Your contact information 2. Model name, BIOS version and problem type. -
Page 97: Mezzanine Card Support List
EP2C626D24LM / EP2C622D24LM / EP2C621D24LM-AB Appendix A Mezzanine Card Support List This motherboard supports the following ASRock Rack mezzanine cards. Mezz Card Type Mezz Slot Type Supported MB Model Model LAN Card Mezz Type A M350 LAN Card Mezz Type A...