CFM TBF120 Installation & Maintenance Instructions

A A
R R E E A A D D A A N N D D S S A A V V E E T T H H E E S S E E I I N N S S T T R R U U C C T T I I O O N N S S F F O O R R F F U U T T U U R R E E R R E E F F E E R R E E N N C C E E
R R E E A A D D A A N N D D S S A A V V E E T T H H E E S S E E I I N N S S T T R R U U C C T T I I O O N N S S F F O O R R F F U U T T U U R R E E R R E E F F E E R R E E N N C C E E
B B E E F F O O R R E E I I N N S S T T A A L L L L A A T T I I O O N N
W W A A R R N N I I N N G G ! !
T T O O R R E E D D U U C C E E T T H H E E R R I I S S K K O O F F F F I I R R E E , , E E L L E E C C T T R R I I C C A A L L S S H H O O C C K K , , O O R R
I I N N J J U U R R Y Y T T O O P P E E R R S S O O N N S S , , O O B B S S E E R R V V E E T T H H E E F F O O L L L L O O W W I I N N G G : :
1. Use this unit in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work including the electrical wiring must
be done, in accordance with all applicable codes and
standards, by a qualified person.
4. When cutting into ceilings, take care not to damage
concealed electrical wiring or any other hidden utilities.
5. Ducted fans must always be vented to the outdoors.
6. NEVER place a switch where
it can be reached from a
tub or shower. To prevent
electrical hazards the fan
must be installed so as to
prevent water from entering
the fan. The fan must not be
installed in a place that is
prone to water leakage.
7. Not for use in cooking
areas. (Figure 1)
8. These fans must be mounted
to structural members that are strong enough to support
the fan's weight.
9. The fan must be properly grounded.
10. Do not allow foreign objects to enter the fan; this could
result in electric shock or fan damage.
11. Do not block the air intake or exhaust.
12. The fan should not be turned on and off rapidly.
13. If the fan is not operating properly, shut the power off
immediately, and have a certified electrician inspect it and
have it serviced as required.
14. Do not clean the fan with corrosive chemicals nor water in
excess of 60C (140F).
15. Power supply wiring is to be No. 14AWG wire or larger
(suitable for at least 90C (190F)).
16. Not for use outdoors.
17. For the lighted units, use only PL type 26W lamps and
a maximum of 4W type E12 T20 lamp for the night light
(models TBFR90L, TBFS90L, TBFR120L, TBFS120L).
18. The fan is type IC (Inherently Protected).
F F S S
E E R R O O A A N N U U P P E E R R I I O O R R
P P A A C C K K A A G G E E C C O O N N T T E E N N T T S S
• A A e e r r o o F F a a n n superior bathroom fan
• Mounting brackets (3)
• Lamps - 26W PL & 4W night light (selected models only)
Cooking area
Do not install above
or inside this area
o o
45 45
Cooking
Floor
Equipment
Figure 1
I I N N S S T T A A L L L L A A T T I I O O N N & & M M A A I I N N T T E E N N A A N N C C E E
B B
A A T T H H R R O O O O M M
19. The fan must not be installed in a ceiling with an "R" rating
greater than 40.
20. To reduce the risk of injury, install the fan at least 2.1m
(7 feet) above the floor.
21. The following models are suitable for installation over a
shower or tub when installed in a GFCI protected branch
circuit (TBF90, TBF120, TBFR90L and TBFR120L).
22. W W A A R R N N I I N N G G : : To reduce the risk of fire or electrical shock, do
not use this fan with any solid state speed control device.
C C A A U U T T I I O O N N ! !
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. This product is designed for installation in flat ceilings
only. Do not install it in a sloping ceiling or in a wall.
3. To avoid motor bearing damage and noisy unbalanced
impellers keep construction material / dust from entering
the fan.
4. Please read specification label on the product for further
information and requirements.
F F A A N N I I N N S S T T A A L L L L A A T T I I O O N N
The fan should only be installed in a ceiling (see figure 2 for a
typical installation). The fan will accommodate a joist spacing
of 16" with a minimum clearance height of 9".
Power
Ceiling
Figure 2
1. Remove the grille by
gently squeezing the
wire springs
extracting them from
the slots in the housing.
2. Remove the electrical
box cover and install
the 3 brackets on the
fan housing. (Figure 3)
I I N N S S T T R R U U C C T T I I O O N N S S
F F
A A N N S S
Housing Fan Outlet
Ceiling Joist
Grille
Mounting
Electrical
Electrical
Bracket
Box
Box Cover
and
Figure 3