TRENDnet TEG-S4000 User Manual
  1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Switch
  5. TEG-S4000
  6. User manual
TRENDnet TEG-S4000 User Manual

TRENDnet TEG-S4000 User Manual

4-slot modular switch
Hide thumbs Also See for TEG-S4000:
Table of Contents

Advertisement

Quick Links

Download this manual
TEG-S4000
4-Slot Modular Switch
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet TEG-S4000

Summary of Contents for TRENDnet TEG-S4000

  • Page 1 TEG-S4000 4-Slot Modular Switch User’s Guide...

  • Page 2: Copyright Statement

    Copyright Statement     COPYRIGHT 2003 ALL RIGHT RESERVED. First Edition. Printed in Taiwan. All trademarks are the properties of their respective owners. No portion of this document may be reproduced, altered, adapted or translated without the prior written approval. FCC Statement This equipment has been tested and found to comply with the limits for a class A device, purauant to part 15 of the FCC rules.

  • Page 3: Chapter 1 Introduction

    Chapter 1 Introduction The 4-Slot Modular Switch are multi-speed network devices combining Ethernet, Fast Ethernet and Gigabit Ethernet capabilities in a single compact, rack-mountable cabinet. Combining 10Mbps Ethernet, 100Mbps Fast Ethernet and Gigabit Ethernet interfaces in one unit allows these switches to unclog existing LANs and provide a path to efficient, high-speed networking.
  • Page 4 Four Rubber feet User manual...
  • Page 5 Device Description, Features and Capabilities 4-Slot Modular Switch Front and Rear Panels This section describes the features on the front and rear panels of the 4-Slot Modular Switch unit. Figure 1-2. Front Panel Figure 1-3. Rear Panel All LED status indicators are located on the FRONT panel of the switches.
  • Page 6 Red Full Duplex/Col indicators are illuminated when that port is in full duplex mode. The indicator is off when that port is Full in half duplex mode Duplex/Col When a collision occurs on the network connected to a port, that Full Duplex/Col indicator blinks.
  • Page 7 Filtering and forwarding rate of 14,880~148,800 packets per second...
  • Page 8 2 ports 100Base-FX Fiber Module Figure 1-6. 2 port 100Base-FX Module Front View When installed into a 4-Slot Modular Switch, this Module provides a 100Mbps Fast Ethernet fiber port which can be used to: Connect the Switch to the backbone of your network; that is, to a basement switch, hub or router Connect the Switch to a 100Mbps server or end-station...
  • Page 9 2 ports 100Base-FX Fiber Module Features Conforms to IEEE 802.3u Fast Ethernet standard Support for SC or ST fiber connectors (optional) Supports half and full duplex modes via DIP switches Store-and-forward switch architecture for abnormal packet filtering 2 switching 100Mbps Fiber Ethernet ports Back-plane up to 2.4Gbps 5 Mbytes Packet Buffer Automatic address learning with 12K address entry...
  • Page 10 Port 1 Port 2 DIP Sw itch Location Port 3 Port 4 Figure 1-9. Location and setting duplex mode The following Table1-3. lists the ports operating modes based on the DIP switch position. PORT 1 PORT 2 Half-Duplex Half-Duplex Full-Duplex Full-Duplex Table 1-3.
  • Page 11 module. 1000Base-SX/LX Fiber Module Figure 1-10. 1000Base-SX/LX Front View When installed into a 4-Slot Modular Switch, the 1000Base-SX/LX Module provides 1 Gigabit Ethernet ports which can connect the 4-Slot Modular Switch to a Gigabit Backbone Switch or Server with Gigabit NIC. 1000Base-SX/LX Fiber Module Features Conforms to IEEE 802.3z draft 4.2 and 802.3x standard...
  • Page 12 1x1000Base-T Ethernet Port 128 KBytes packet buffer support Automatic address learning with 4K address entry storage Standard auto-negotiation for speed, duplex mode and flow-control for MII and GMII PHYs Backpressure for half duplex...

  • Page 13: Chapter 2 Planning Your Network

    Chapter 2 Planning your Network Before you install your 4-Slot Modular Switch, you should review the guidelines for setting up Ethernet networks. Further, you should plan your network to take maximum advantage of its switching capabilities. 10Base-T Ethernet Network Guidelines The maximum length of a 10Base-T cable segment is 100 meters (328 feet).
  • Page 14 1000BASE-SX /LX / TX Network Guideline 1000BASE-SX In Multi-mode, the fiber optic segment cannot exceed 220m (62.5/125µm) or 500m (50/125µm) in length. 1000BASE-LX In Multi-mode, the fiber optic segment cannot exceed 550m(62.5/125µm), 550m(50/125µm) in length. In single mode the fiber optic segment cannot exceed 10km(9/125µm).
  • Page 15 You can expand your 10Base-T or 100Base-TX or 1000Base-SX/LX/T networks beyond its hub limit by adding a 4-Slot Modular Switch. 10Base-T Networks 10Base-T Networks are limited to four hubs between any two nodes. By adding your 4-Slot Modular Switch to a network, you can divide that network into segments with their own collision domains.
  • Page 16 Figure 2-2. Expanding your 100Base-TX network (Class I) Collapsed Backbone Link Traditionally, bridges and routers have been used to link local area networks into one interconnected network. But these devices involve difficult management and long traffic delays. The 4-Slot Modular Switch providers multiport bridges with short delays, easy setup and maintenance, making it ideal for backbone links.
  • Page 17 Figure 2-3. 4-Slot Modular Switch 100/1000 Hub in a collapsed backbone link Fileserver Link 100Base Solution With a fileserver link, you can increase file server performance by increasing the Hub's bandwidth between one or more fileservers and the workgroups they serve. If you connect 10Mbps workgroup hubs to the 10Mbps ports on the 4-Slot Modular Switch, traffic in one workgroup will not interfere with the performance of...
  • Page 18 Figure 2-4. Fileserver Link Connecting servers through 100Base-TX ports increases performance to the clients, even if the clients are on 10Base-T segments. Because multiple 10Base-T devices can access the file server at the same time through a 100Base-TX connection, performance increases to beyond the performance of standard 10Base-T or 100Base-TX hubs.
  • Page 19 Figure 2-5. Used as a Multiport Bridge Using your hub, you can also connect 10Base-T networks and 100Base-TX and 1000Base-SX/LX networks together for more flexibility in your network topology. As in the Figure 2-5 shown above, the 4-Slot Modular Switch can connect through one port to a 10Base-T network, and through another port, connect to a 100Base-TX port, creating one network.

  • Page 20: Chapter 3 Installation

    Chapter 3 Installation The Switch can be installed quickly and easily. However, for an installation with minimum impact on the existing network, please read this chapter carefully. Installing a 4-Slot Modular Switch involves three steps: 1. Choosing a location 2. Supplying power 3.
  • Page 21 Rack Installation Your switch comes with two rack mounting brackets. you can use these brackets to mount the switch on an EIA standard 19" rack. Attach the brackets to the switch, using the screws provided. Figure 3-2. Attaching the mount brackets for rack installation Next, install the switch in the rack using the screws provided to attach the brackets to the rack.

  • Page 22: Chapter 4. Module Installation And Removal

    make sure that: The 10Base-T twisted pair Ethernet cabling is Category 3 or above. The 100Base-TX Fast Ethernet cabling is tested Category 5. The 1000Base-T Gigabit Ethernet cabling is tested Category 5 enhanced. The 100Base-FX fiber cabling is 62.5/125 micron multimode fiber, or 9/125 micro single-mode fiber.
  • Page 23 from the rear of the Switch. Do not remove any other screws from the rear of the Switch. 3. Keep the blanking plate and screws in a safe place. If you remove the Module at any time, you must replace the blanking plate to prevent dust and debris from entering the Switch and to aid the circulation of cooling air.

  • Page 24: Appendix A. Technical Specifications

    a. Remove the protective plastic covers from the fiber connectors on the Module. b. Ensure that the Switch is powered up. c. Plug the SC connector on the fiber cable into the fiber socket on the Module. d. Connect the other end of the fiber optic segment to an appropriate device fitted with a 1000Mbps adapter.
  • Page 25 100V AC to 240V AC Environment: Operating Temperature 0℃ to 45℃ Humidity 10% to 90% RH Dimensions: 440mm x 225mm x 66mm EMI & Safety: FCC Class A, CE, UL/CSA Physical Characteristics: Buffer Size 256 Kbytes shared buffer for 10/100Base-TX module, and 1000T module 5 Mbytes shared buffer for 100Base-FX module.
  • Page 26 1000Mbps indicator for 1000T module Power on/off indicator...

  • Page 27: Appendix B. Pin Assignments

    Appendix B. Pin Assignments RJ-45 station ports can be attached to any device which use a standard network interface (e.g., a workstation, server, bridge or router). RJ-45 daisy-chain ports can be cascaded to a station port on similar networking devices (e.g., another switch or hub). Use unshielded twisted-pair (UTP) for RJ-45 connections: 100 ohm Category 3,4 or 5 cable for 10Mbps connections or 100 ohm Category 5 cable for 100Mbps connections.
  • Page 28 Schematics for both Straight-Through and Crossover twisted-pair cable are shown below. Straight-Through Switch Adapter 1 RD ＋ 1 TD ＋ 2 RD － 2 TD － 3 TD ＋ 3 RD ＋ 6 TD － 6 RD － Technical Support TRENDware provides free technical support for customers worldwide for the duration of the product’s warranty period.

Table of Contents