Related Manuals for TRENDnet TEG-S4000i
Summary of Contents for TRENDnet TEG-S4000i
- Page 1 TEG-S4000i 4-Slot SNMP Modular Switch Ethernet / Fast Ethernet / Gigabit Ethernet User’s Guide Version 2.0 23-April-2003...
-
Page 2: Release Note
Update Version Progress status 23/04/2003 V2.0 On checking Release Note 4 slot modular switch manual Remark 1. 10/100 TX (48350) spec. MAC: 4K Buffer:256Kbytes 2. 2/4/8 100FX (48310 ) spec. MAC12k, Buffer:5Mbytes 3. Gigabit module (48360) MAC:4K, Buffer 128 Kbytes... -
Page 3: Table Of Contents
Table of Content Introduction Product Overview Network Configuration Connecting to the Network Web-Based Management SNMP Management Product Specifications Appendix A. Internet Explorer Setting Appendix B. VLAN Setting... -
Page 4: Introduction
Congratulations on purchasing the Modular Switch. This Modular Switch is a combination of 4-slot host cabinet and optional 4 kinds of media modules. A maximum 32 x 10/100Base-TX switched ports can be achieved using 4 x 8 port 10/100 Base-TX switch modules. -
Page 5: Key Features
Web Browser. Just click your mouse instead of typing cryptic command strings. However, the Modular Switch can also be managed via Telnet, Console, or third-party SNMP Management. Key Features Conforms to IEEE 802.3, 802.3u, 802.3z, 802.3ab and... -
Page 6: Management Methods
Managing the Modular Switch in this method requires a direct connection between PC and the Switch. While Telnet management is done over the network. Once the Switch is on the network, you can use Telnet to Log in and change the configuration. -
Page 7: Snmp Network Management
The Modular Switch provides an embedded HTML web site residing in flash memory. It offers advanced management features and allow users to manage the Modular Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. For more information, See Section 5 Web-Based Management. -
Page 8: Package Contents
Package Contents Unpack the carton of the Modular Switch and verify them against the checklist below. Modular Switch Power Cordially Four Rubber Feet RS-232 cable User Guide Modular Switch Rack-mounted Kit Power Cord Compare the contents of your Modular Switch package with the standard checklist above. -
Page 9: Product Overview
The Modular Switch is a modular unit, and its chassis contains four slots. All optional models come with the built-in CPU modules. The LEDs are located on the front panel of the Switch to allow you to monitor the operation and performance at a glance. All ports can be used for network configuration. -
Page 10: Led Indicators
The 3-pronged power plug and On/off switched are located at the Rear Panel of the Modular Switch displayed in Figure 2-2. The Switch will work with AC in the range 100-240VAC, 50-60Hz. Figure 2-2. Rear Pane LED Indicators All LED status indicators are located on the FRONT panel of the switch. -
Page 11: Static Address
This Console port is used to connect a management station or terminal with the switch. Out-of-band management means go through the RS-232 port. For more information about switch management, see Section 4 “ Connecting to the Network ”. Software Concepts... -
Page 12: Port Trunking
Virtual LANs ( VLANs ) A VLAN is a group of switch ports designated by the switch as belonging to the same broadcast domain. This feature allows workgroups to be defined on the basis of their logical function instead of their physical location, and does not require recabling. -
Page 13: Port Mirror
Broadcast Storm Filter Storm Filter can avoid any flooded data packets. This feature prevents the bursts of broadcast traffic. Excessive broadcast packets ( Broadcast Storms ) can be filtered in our managed switch by enabling the "Broadcast Storm Filtering" option. -
Page 14: Network Configuration
The switch can be used as a standalone switch for a group of heavy traffic users. Switching is brought to the desktop either through a single end-station per switch port or through a multi-port hub. -
Page 15: Departmental Bridge
When the network needs expansion, you can simply daisy-chain the switch to any IEEE 802.3 ( Ethernet ), IEEE 802.3u ( Fast Ethernet ), IEEE 802.3z ( Gigabit Ethernet ) compliant hub. This switch can also cooperate with a wide range of networking devices (e.g., firewall routers and printer servers) added to the network. - Page 16 Figure 3-2. Departmental Bridge Application NOTE: Full-duplex operation only applies to point-to-point access (for example, when attaching the switch to a workstation, server, or another switch). When connecting to hubs, use a standard cascaded connection set for half-duplex operation.
- Page 17 The switch support up to 4095 port-based 802.1Q-compatible virtual LANs (VLANs). Port-based VLAN Workgroup You can group the switch ports into broadcast domains by assigning them to the same VLAN to increase network capacity and performance. With network segmentation, each switch port connects to a segment that is a single broadcast domain.
- Page 18 VLANs for shared resources, such as servers, printers, and switch-to-switch connections. It is also possible to have resources exist in multiple VLANs on one switch as shown in the following figure. In this example, stations on different VLANs share resources. As a result, VLAN 1 and VLAN 2 can access VLAN 3 for printing.
-
Page 19: Connecting To The Network
A dry cool place: Keep the switch away from moisture. Avoid direct sunlight, heat source, and high amount of electromagnetic interference around. Mounting tools: If you intend to mount the switch on a rack, make sure you have all the tools, mounting brackets, screws. -
Page 20: Mounting The Switch
B. Remove adhesive backing from your Rubber Feet. C. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can prevent the Switch from shock/vibration. Figure 4-1. Attaching Rubber Feet to each corner... -
Page 21: Rack Mounting
Rack Mounting The Modular Switch come with a rack-mounted kid and can be mounted in an EIA standard size, 19-inch Rack. The Switch can be placed in a wiring closet with other equipment. Perform the following steps to rack mount the switch: A. - Page 22 After all network cables are connected, plug the power cord into the power socket on the back panel and the other end into a power outlet. Turn the power on using the power switch on the back panel. Check the front panel Power indicator to see if power is properly supplied.
-
Page 23: Connecting The Switch
When the switch passes the self-test within 10 seconds, the Link/ACT LED turns on. If the switch fails the self-test, the Diagnostic LED will blink. Connecting the Switch The serial console port is a male DB-9 connector that enables a connection to a PC or terminal for monitoring and configuring the switch. - Page 24 After connected to the Console port, turn on the PC or terminal and configure its communications parameters to match the following default characteristics of the console port: Baud Rate: 9600 bps Start Bit: 1 Data Bits: 8 Stop Bit: 1 Parity: none Figure 4-5.
-
Page 25: Assigning Ip Address
After you have attached a terminal or PC with emulation software and you are ready to make a connection using a web browser. You have to firstly assign IP information to the switch. It allows you to manage the switch once it has an IP address. -
Page 26: Port Setting
Select IP Address on the Device page, and enter a unique IP address for the switch, and press Enter. ( Default IP address is 192.168.16.1 ) Select Subnet Mask on the Device page, and enter the subnet mask ( IP Netmask ) address, and press Return. ( Default subnet Mask is 255.255.255.0 ) - Page 27 a. More function to choice after typing 1, or 2 b. Pick any number you need to set up, for example, the option 2 is for the Full or Half mood setting.
-
Page 28: Address Table
Address table User can view the node’s MAC address table of system, per module or per port, that attached on the device. Spanning Tree Protocol Spanning tree is a link management protocol that provides path redundancy while preventing undesirable loops in the network. - Page 29 Broadcast Storm Filter IGMP Internet Group Multicasting Protocol (IGMP) is used to support real-time applications such as video conferencing or streaming audio.
- Page 30 VLAN Mode (2 modes) VLAN For Cpu(2 VLANs)
-
Page 31: Secure Ip For Telnet And Http
Secure IP for Telnet and HTTP The IP security is for Telnet and HTTP , if device is installed in a internet environment , switch may be attach by Hacker, then the system maybe will crash, for prevent this status, you can enable the function and setting the IP address, it provides four IP address, only authorized IP address can manage device. -
Page 32: Web-Based Management
) And you don’t need to change any configuration if you use Netscape browser. System Login Start Internet Explorer Type http:// and the IP address of the Modular Switch ( for example, the default is 192.168.16.1 ) in the Location or Address field. Press Enter. -
Page 33: System Configuration
Figure 5-1: The Password Window 3. The Password screen appears. 4. Type user name and password. The default is “ root ” for both. 5. Press “Enter” or Click ”OK”, then the Home Screen of the Web-based management appear. System Configuration Figure 5-2 The Home Page Screen... - Page 34 Home The Home page displays the configuration of the Modular Switch. System Name : An administratively-assigned name of the managed unit, can be modified in SNMP page. System Location : The physical location of this managed unit ( e.g., laboratory, 3 floor ), can be modified in SNMP page.
- Page 35 Module, 1-port Gigabit 1000Base-F ( SX ) Fiber Module, 8-port auto-sensing 10/100Base-TX Switch Module, and 4-port 100Base-FX (ST) Fiber Module are installed into the Switch. Any four of the following modules can be installed to the Switch. • 8-port auto-sensing 10/100Base-TX Switch Module •...
- Page 36 Ports Inside Ports page, you can enable/disable each port, configure Speed/Duplex for each port, and assign VLAN ID. The Port Management table shows the port status of all ports. You can also change some properties of all ports in this table. •...
- Page 37 window. Statistics The Statistic page displays the detailed information about each port. You can compare and evaluate throughput or other port parameters. All screen data is updated automatically and you can also update the data manually. Figure 5-5-1 The Statistics Page The Port Counters table shows 8 counters for each port in each module.
- Page 38 • Collision: the total number of collisions that occurred during reception and transmission You can clear 8 counters of some ports by select the corresponding "Clear" check boxes then press "Clear" button. To clear all counters of all ports, press the "Select All" button then "Clear" button. Statistics 2 The statistics 2 page displays the detailed packet size information...
- Page 39 VLAN ( Virtual LAN ) A port-based VLAN is a group of switch ports designated by the switch as belonging to the same broadcast domain. If a broadcast packet is received from a port, it will forward this broadcast packet only to those ports belonging to the same VLAN.
- Page 40 (up to 8) within the same module into a single logical link. The port trunk acts as a single link between switches. Multiple trunks may be implemented in this switch, but only one trunk can be created within a module.
- Page 41 Figure 5-7 The Trunk page You can add, edit and remove port members of each trunk and then press "Apply" button after you have finished configuring the trunks you need. ( Note: Make sure trunking ports are in the same VLAN group. ) STP (Spanning Tree Protocol) Spanning tree is a link management protocol that provides path redundancy while preventing undesirable loops in the network.
- Page 42 Root Path Cost: the path cost to the root switch from this switch Root Port: the port providing the best path from the switch to the root switch The Spanning Tree Bridge Configuration describes this switch information in the spanning tree.
- Page 43 Max Age: the amount of time (in seconds) protocol information received on a port is stored by the root switch, the default value is 20 Hello Time: how often the root switch broadcasts Hello message to other switches, the default value is 2...
- Page 44 Figure 5-8-1 The STP lower page Note: when you enable the spanning tree protocol, because all ports in the switch will listen and learn, you may lose communication to the switch you are managing. Wait about 2 times forward delay...
- Page 45 Port Security Port Security allow you to restrict specific MAC addresses to reside in some port. For example, a dummy hub is attached to some port for extension, and you just only allow 2 users to access this port at the same time, you can use the port security window to set the parameters.
- Page 46 option. Priority There are two priority queues ( high and low ) on each port. Each port arbitrates between two transmit queues ( high and low priority ). The arbitration uses weighted round-robin between the high and low priority queues, and you can adjust this weight. Programmable Mapping of 802.1p to Internal Priority The received packets with 802.1q tag are assigned priority according to a flexible (fixed for the old 48310 and 48320 module)
- Page 47 Priority 2 Each port can parse the header of an incoming IPv4 header and identify the Type-Of-Service byte (TOS field). This is extremely important with the deployment of Microsoft Windows 2000 and the emerging DiffServ standard, which marks Voice-Over-IP and other real-time traffic using this field.
- Page 48 IGMP is used in multicast communication network applications where one or more servers, for example, video servers, generate multicast traffic. If you want your switch to support multimedia and IP multicast, enable this option (default is enabled). When this option is enabled, this switch only directs the multicast data packets to the ports where needed, saving bandwidth.
- Page 49 Static Address You can lock a certain MAC address ( associated with a host, ) to a certain port. Once a certain MAC address is locked to a certain port, this MAC address will not receive any packets if it is moved to another port.
- Page 50 Figure 5-13 The Static Address page Broadcast Storm Filter Excessive broadcast packets (broadcast storms) can be filtered in our managed switch by enabling the "Broadcast Storm Filtering" option. When this option is enabled, if more than 3000 packets per second...
- Page 51 Port Mirror If you want to monitor all receive and transmit packets of one port. You can do the following: • Choose the monitored port in "Mirror Source Port" choice box in the corresponding mirror source module. Only one port can be monitored in one module at the same time •...
- Page 52 IP Config You can change the IP address, subnet mask and default gateway of the managed node. (You can also do that from RS232 console). Enter the IP address, subnet mask and default gateway in the corresponding edit box. If you want to change the user name or password for the managed node, the following steps is needed: •...
- Page 53 Figure 5-16 The IP Config page SNMP To set system name, system location and system contact, you can type the desired text string in the corresponding edit box. To set the "get request" and "set request" community name, you can type the desired text string in the corresponding edit box.
-
Page 54: Save And Reboot
Figure 5-17 The SNMP page Save and Reboot Save You can save current settings by click the "Current Settings" checkbox then press the "Apply" button next to the checkbox. You should reboot the system so that your current settings will take effect. - Page 55 If you want to use the factory default settings, click the "Factory Default Settings" checkbox then press the "Apply" button next to the checkbox. You should reboot the system so that the factory default settings will take effect. Reboot If you want to reboot system, click the "Reboot System" checkbox then press the "Apply"...
-
Page 56: Snmp Management
Note: If you can't upgrade your new firmware successfully, try again ( don't shut down the switch ). SNMP Management This section describes how to configure and manage the switch by accessing Management Information Base (MIB) objects with the SNMP protocol. - Page 57 SNMP performs all operations using the “GET”, “GETNEXT” and “SET” commands. The SNMP agent that resides on the switch can respond to MIB-related queries being sent by the network management software. The SNMP agent gathers data from the MIB, which keeps information about device parameters and network data.
-
Page 58: Product Specifications
GETNEXT Specify an SNMP object in a network device and then retrieve information about the next few SNMP objects in the device. Modify and store values of SNMP objects in a network device. The reply to a GET, GETNEXT, and SET RESPONSE commands sent by a SNMP agent TRAP... - Page 59 Compliance IEEE 802.3u 100BASE-TX/FX Ethernet, IEEE 802.3z 1000BASE-LX/SX Ethernet, IEEE 802.3ab 1000BASE-T Gigabit Ethernet ANSI/IEEE standard 802.3 N-Way Auto-negotiation Max Forwarding 14,880 pps per Ethernet port, Rate and 148,800 pps per Fast Ethernet port Max Filtering 1,488,000 pps per Gigabit Ethernet port Rate LED Indicators Per Port: 8 port Auto-sensing:...
- Page 60 10% to 90% ( Non-condensing ) Operational Humidity Power Supply Input rate: 100~240VAC, 50~60Hz Internal universal power supply: DC 3.3V/13A, 5V/4A 33~45 Watt depended on modules Power Consumption FCC Class A, CE Mark cUL, UL Safety...
-
Page 61: Internet Explorer Setting
Appendix A. Internet Explorer Setting If using IE 4.x and later version, you have to modify the browser setting to enable Java applets to use network ports. We use Internet Explorer 5.0 as demonstrational sample: We first select ”Internet Optional..” under “Tools” of function bar, then follow the step-by-step execution. - Page 62 Step 3 : click “ sites ” Step 4 : add the IP of the Modular Switch to the zone, click " Add " Step 5: Disable left-bottom box – Require server verification for all sites in this zone, then click "OK...
- Page 63 Step 6: go back to Internet Options, then click “ Customer Level ” Step 7: pull down rolling to find “Java ” Step 8: select “ Custom ” under “Java ”...
- Page 64 Step 9:select”Java Custom Setting” Step 10: select “Edit Permissions” Step 11: select “Enable” under ”Unsigned Content”,...
-
Page 65: Appendix B. Vlan Setting
Appendix B. VLAN Setting In Appendix B, We provide two examples of VLAN management on VLAN Group Configuration. The two examples will show you how to Configure VLAN Group: Port-Based VLAN The following example shows you how to create 2 Port-based VLANs including two overlapping ports. - Page 66 Before you begin to create new VLAN Group, you need to set PVID number on Ports page as below: We set VLAN ID of Ports (1~4 ) 1, and PVID of Ports ( 5~8 ) 2. Remember to click “ Apply “ button after you finish your setting. Then, return to VLAN page, and the screen displays as below:...
- Page 67 Tagging ( Mac Address based ) VLAN This method of tagging is defined in the IEEE 802.1Q standard, to configure switch port by the tagging function that allows the port to transmit tagging frame. VLAN Tagging can only be used if the devices at both ends of a link support IEEE 802.1Q.
- Page 68 First, on Ports page, we set VLAN ID 1, 2, 3 as below. Click the checkbox of Tagged on Module 1, port 1.( ,which is a Gigabit port ) Remember to click “ Apply “ button after you finish your setting. Then, return to VLAN page, you will see the screen as below.
- Page 69 Remember to click “ Apply “ button after you finish your setting. Now, you have finished one Tagging VLAN setting. While you connect this Switch to another Modular Switch to form tagging VLAN, remember that the other Modular Switch should have...
-
Page 70: Technical Support And Service
Appendix C. Technical Support and Service For this advanced Intelligent Switch, we provide easy access to technical support information through a variety of services. Here describes these services. Registration Fill in the Registration Card in the package and fax it to the fax number on the card, or you can visit the online Web site on the card. - Page 71 TRENDware provides free technical support for customers worldwide for the duration of the product’s warranty period. Technical Support via Telephone: Fax: Technical Support via Internet: Http://www.trendnet.com E-mail: support@trendware.com Technical Support Hours: 7:00AM ~ 6:00PM, Monday ~ Friday, Pacific Standard Time...