List Of Supported Signals) (Y/P Signals)); List Of Supported Signals (Video, S-Video Signals); Pin Assignment Of Computer 1 In, Computer 2 In & Monitor Out Terminals; Control Terminal - Toshiba TLF-XD2000 Owner's Manual

Specifications (Continued)
■ List of supported signals (Y/P
Signal format fh(kHz)
480i(525i)@60Hz 15.73
480p(525p)@60Hz 31.47
576i(625i)@50Hz 15.63
576p(625p)@50Hz 31.25
720p(750p)@60Hz 45.00
720p(750p)@50Hz 37.50
1080i(1125i)@60Hz 33.75
1080i(1125i)@50Hz 28.13

■ List of supported signals (Video, S-Video signals)

Video mode fh(kHz)
NTSC 15.73
PAL 15.63
SECAM 15.63
PAL-M 15.73
PAL-N 15.63
PAL-60 15.73
NTSC4.43 15.73
■ Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &
MONITOR OUT terminals
5 1
10 6
15 11
Mini D sub 15 Pin connector
Input Signal
• RGB input
0.7V (p-p) 75 1
RGB signals:
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/P /P input
B R
1.0V (p-p) 75 1
Y signal:
0.7V (p-p) 75 1
P /P signals:
B R
/P signals)
B R
fv(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
fv(Hz) fsc(MHz)
60 3.58
50 4.43
50 4.25 or 4.41
60 3.58
50 3.58
60 4.43
60 4.43
Pin Pin description
No. During RGB input During Y/P /P
B R
1 Video signal (R) Color difference signal (P
2 Video signal (G) Luminance signal (Y)
3 Video signal (B) Color difference signal (P
›
4 GND
›
5 GND
6 GND (R) GND (P )
R
7 GND (G) GND (Y)
8 GND (B) GND (P )
B
›
9 N.C
›
10 GND
›
11 GND
›
12 N.C
›
13 Horizontal sync signal
›
14 Vertical sync signal
›
15 N.C
› Do not connect anything.
52

■ CONTROL terminal

● Pin assignment
7
8
5
2
Mini DIN 8 pin connector
● Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
● Main Commands
input Item
) Power on
R
Power off
) Icon display on
B
Icon display off
Auto setting (RGB input)
Status display on
Status display off
Note
• Contact your dealer for control cable and other commands.

■ Separately sold product

Replacement Lamp
Pin No. Signal Name
1 RXD
6 2 CTS
3 DSR
4 GND
3
5 RTS
4 6 N.C
7 TXD
1
8 GND
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length: 1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge ACK (06h) CR (0Dh) Data
ACK (06h) ESC (1Bh)
No acknowledge NAK (15h)
Command
PON
POF
MO0
MO1
PAT
DON
DOF
Model TLPLW11
53
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
... Normally ended
... Aborted