List Of Supported Signals) (Y/P Signals)); List Of Supported Signals (Video, S-Video Signals); Pin Assignment Of Computer 1 In, Computer 2 In & Monitor Out Terminals; Control Terminal - Toshiba X3000AU - XGA LCD Projector Owner's Manual

Specifications (Continued)
■ List of supported signals (Y/P
Signal format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz

■ List of supported signals (Video, S-Video signals)

Video mode fh(kHz)
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
■ Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &
MONITOR OUT terminals
5 1
10 6
15 11
Mini D sub 15 Pin connector
Input Signal
• RGB input
RGB signals: 0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/P /P input
B R
Y signal: 1.0V (p-p) 75 Ω
P /P signals: 0.7V (p-p) 75 Ω
B R
Downloaded from www.Manualslib.com
/P signals)
B R
fh(kHz) fv(Hz)
15.73 59.94
31.47 59.94
15.63 50.00
31.25 50.00
45.00 60.00
37.50 50.00
33.75 60.00
28.13 50.00
fv(Hz) fsc(MHz)
15.73 60 3.58
15.63 50 4.43
15.63 50 4.25 or 4.41
15.73 60 3.58
15.63 50 3.58
15.73 60 4.43
15.73 60 4.43
Pin Pin description
No. During RGB input
1 Video signal (R) Color difference signal (P
2 Video signal (G) Luminance signal (Y)
3 Video signal (B) Color difference signal (P
4 GND ∗
5 GND ∗
6 GND (R) GND (P
7 GND (G) GND (Y)
8 GND (B) GND (P
9 N.C ∗
10 GND ∗
11 GND ∗
12 N.C
∗
13 Horizontal sync signal ∗
14 Vertical sync signal ∗
15 N.C ∗
∗ Do not connect anything.
58
manuals search engine

■ CONTROL terminal

● Pin assignment
5
Mini DIN 8 pin connector
● Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
● Main Commands
During Y/P /P input
B R
) Power on
R
Power off
) Icon display on
B
Icon display off
Auto setting (RGB input)
) Status display on
R
Status display off
)
B
Note
• Contact your dealer for control cable and other commands.

■ Separately sold product

Replacement Lamp
Pin No. Signal Name
7 1
8 6 2
3
4
3
5
4 6
7
2 1
8
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge ACK (06h) CR (0Dh) Data
ACK (06h) ESC (1Bh)
No acknowledge NAK (15h)
Item Command
PON
POF
MO0
MO1
PAT
DON
DOF
Model TLPLW12
59
Description
RXD Receiving data
CTS Consent to send
DSR Data set ready
GND Signal ground
RTS Request to send
N.C No connection
TXD Sending data
GND Signal ground
1 bit
... Normally ended
... Aborted