Contents Important Safety Your Wireless HD AV Connect What is in the box Overview The transmitter The receiver The remote control Installation Connect the transmitter to your HD devices Connect the receiver to the HDTV set Connect the IR blaster and IR sensor extender cables Install remote control batteries Activate your Wireless HD AV...
1 Important Safety This ‘bolt of lightning’ indicates uninsulated material within your unit may cause an electrical shock. The ‘exclamation mark’ calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. Warning •...
Page 5
n Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
2 Your Wireless HD AV Connect Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. What is in the box Note • Make sure you have all these items in the box. Contact your dealer for any missing or damaged items.
3 Overview The transmitter Front view Source LEDs It displays the current source input. SOURCE Press to switch the button source input of the transmitter. Power button Press to turn the with the LED transmitter on/off indicator Rear view DC IN jack Connect the power adapter of the transmitter.
The remote control POWER Press to turn the button transmitter and receiver on/off. INFO Displays on the HDTV button the connection status of the receiver. Press to switch the IR button blaster frequency to meet the requirement of the source device. SOURCE Press to switch the button...
4 Installation Connect the transmitter to your HD devices You can connect two audio/video sources to the transmitter at the same time, but only one source can be selected and played. Connect the audio/video source to the transmitter using the supplied HDMI cable. •...
Connect the IR blaster and IR sensor extender cables • If you cannot use the remote control of your device, follow the steps in this section to connect the sensor extender cables . Connect the infrared blaster or sensor extender cables if necessary.
5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV HDMI OUT IR IN DC 5V HDM I Go to the source menu under the settings menu of your HDTV. Select the HDMI input to which the receiver is connected.
The maximum transmission range is up to 65 feet (19.7 meters). • If more than one set of Philips Wireless HD AV Connect is placed in the same room, make sure that the minimum distance among each one is 6 feet 6 inches (2 meters).
6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. Mount your receiver on the wall Select a spot near the HDTV. Drill two holes in the wall. Make sure that the distance between the two holes is ”...
Mount your receiver on the back of the HDTV Remove the white protective film from one of the supplied adhesive tapes. Secure the glued side of the adhesive tape and attach it to the central bottom area of the receiver. Select a flat location on the rear side of the HDTV.
8 Notice Notice for USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1-888-744-5477. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. Philips’ liability is limited to repair or, at its sole option, replacement of the product. Incidental, special and consequential damages are disclaimed where permitted by law. This warranty gives you specific legal rights.
9 Frequently asked question The power LED on the receiver is not lit up in red in standby mode. The computer screen image is not full screen on my TV. There is no video displayed on my TV screen. • Make sure that there is power supply for the transmitter and receiver.
Page 19
If the picture quality is poor, what do I do? I cannot hear any sound or the sound is poor, what do I do? I cannot control the source device with the IR blaster. • Make sure that the video resolution of your source device matches the resolution of your HDTV.