Mitsubishi Electric MUZ-LN VG Series Service Manual page 50

OPERATING PROCEDURE
7. Removing the vane motor units (L) (R) (vertical)
and the vane motors (horizontal)
(1) Remove the front panel, the outer vanes (R) (L)
(horizontal), the inner vanes (R) (L), the vane slide
assembly, the panels (U) (R) (L) (F), the corner boxes
(R) (L), Wi-Fi interface, DISPLAY and i-see SENSOR
ASSEMBLY, V.A. clamp, and the electrical cover.
(2) Remove the panel (F) (Photo 3).
(3) Remove the following connector (Photo 8):
<Indoor electronic control P.C. board>
CN151 (Vane motors)
(4) Pull out the drain hose from the nozzle assembly. Pull
and remove the nozzle assembly (catches on left,
right, and center) (Photo 10).
(5) Cut off the cable tie to secure the lead wires on the
right side of the nozzle assembly (Photo 12).
(6) Remove the tape to secure the lead wires and the
aluminum tape on the front of the nozzle assembly.
(Photo 11)
Removing the vane motor (R) (horizontal) and the vane
motor (horizontal) (Photo 14, 15)
(7) Remove the 3 screws of the vane motor unit (R) (hori-
zontal) and remove the lead wires of the vane motor
(R) (vertical), the vane motor(R) (horizontal) and the
vane motor (horizontal).
(8) Remove the 2 screws of the vane motor (R) (horizontal)
from the backside of the vane motor unit (R) (horizon-
tal), and remove the vane motor (R) (horizontal).
(9) Remove the 2 screws of the vane motor (horizontal)
from the backside of the vane motor unit (R) (horizon-
tal), and remove the vane motor (horizontal).
Removing the vane motor unit (R) (vertical) (Photo 15)
(10) Disengage the link of the vane motor unit (R) (vertical).
(11) Remove the screw indicated in , and remove the vane
motor unit (R) (vertical).
Removing the vane motor (L) (horizontal) (Photo 16)
(12) Disengage the link of the vane motor unit (L) (vertical).
(13) Remove the 3 screws indicated in (Photo 16).
(14) Remove the 2 screws of the vane motor (L) (horizon-
tal) from the backside of the vane motor unit (L) (hori-
zontal), and remove the vane motor (horizontal).
Removing the vane motor unit (L) (vertical) (Photo 17)
(15) Disengage the catch of the vane motor unit (L) (verti-
cal), and remove the vane motor unit (L) (vertical).
OBH766C
PHOTOS/FIGURES
Photo 14
Screws of the vane motor
(horizontal) on back side
Vane motor (R)
(horizontal)
Screws of the vane motor (R)
(horizontal) on backside
Photo 15 Vane motor unit (R) (vertical)
Screw of vane motor
(R) (vertical)
Photo 16
Catch
Detach the vane motor units (L) (horizontal and
vertical). Then move them to the direction of
and remove the link of the vane motor unit (L)
(vertical).
Photo 17 Vane motor unit (L) (vertical)
Vane motor unit (L) (vertical)
50
Vane motor unit (R)
(horizontal)
Screws
Vane motor (horizontal) with a
motor on backside
Vane motor unit (R) (vertical)
Link
Vane motor unit (L)
(horizontal)
Screws of the vane motor
(L) (horizontal) on backside
Screws
Vane motor
(L) (horizontal)
,
Link