Kitagawa BS300 Instruction Manual
  1. Manuals
  2. Brands
  3. Kitagawa Manuals
  4. Industrial Equipment
  5. BS300
  6. Instruction manual

Kitagawa BS300 Instruction Manual

Large thru-hole high precision power chuck
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
Large Thru-Hole High Precision Power Chuck
・ This instruction manual is for production engineers and maintenance
personnel in charge of operation of this product. When a beginner uses
this product, receive instructions from experienced personnel, the
distributor or our company.
・ Before installing, operating or maintaining this equipment, carefully
read this manual and the safety labels attached to the equipment.
Failure to follow these instructions and safety precautions could result
in serious injury, death, or property damage.
・ Store this manual near equipment for future reference.
・ If any questions related to safety arise about this manual, please
confirm them with the distributor or our company.
77-1,Motomachi,Fuchu -shi,Hiroshima,726-8610,Japan
BS300
DANGER
Kitagawa Corporation
TEL +81-(0)847-40-0561
FAX +81-(0)847-45-8911
Version 1.10 (2021.08.03)
Original instructions
type

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BS300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kitagawa BS300

Summary of Contents for Kitagawa BS300

  • Page 1 Version 1.10 (2021.08.03) Original instructions INSTRUCTION MANUAL BS300 type Large Thru-Hole High Precision Power Chuck DANGER ・ This instruction manual is for production engineers and maintenance personnel in charge of operation of this product. When a beginner uses this product, receive instructions from experienced personnel, the distributor or our company.
  • Page 2 Preface This manual provides detailed information about how to safely and correctly use the power chuck (BS300 type) for a lathe. Before starting to use this power chuck, read this manual carefully and always follow the instructions and warnings in "Important Safety Precautions" and "Precautions for Use"...
  • Page 3 The chuck and cylinder from Kitagawa Corporation should be used together. If you must use a part not made by Kitagawa, check with us or our distributor to be sure it is safe to do so. We will not be responsible for injury, death, damage or loss caused by use of a chuck or cylinder made by another company unless this use has been approved by Kitagawa or its distributor.

  • Page 4: Table Of Contents

    Table of Contents 1. Structural Drawing and Parts List -----------------------------------------------------------------------5 1-1. Type display 1-2. Structural drawing 1-3. Scope of product 1-4. Parts list Important Safety Precautions ------------------------------------------------------------8 3. Specifications ----------------------------------------------------------------------------------------------15 3-1. Specifications 3-2. Relationship between gripping force and rotation speed 3-3.
  • Page 5 For Machine Tool Manufacturers (Chapter 8) 8. Attachment -------------------------------------------------------------------------------------------------37 8-1. Outline drawing of attachment 8-2. In the case that the back plate must be manufactured (BS300 series) 8-3. In the case of with back plate (BS300A series) 8-4. Attachment of chuck 9.

  • Page 6: Structural Drawing And Parts List

    1. Structural Drawing and Parts List 1-1. Type display Type display as shown below Fig.1 1-2. Structural drawing Fig.2...

  • Page 7: Scope Of Product

    1-3. Scope of product This instruction manual is for the chuck part. Fig.3 ・ To prevent the work from flying, safe design, maintenance and erroneous action prevention of the hydraulic system to maintain the gripping force of the chuck is extremely important. Thoroughly read the “Important Safety Precautions”...

  • Page 8: Parts List

    1-4. Parts list Fig.4 Table 1 Part name Quantity No. Part name Quantity 1 Body 14 Chuck attaching bolt 2 Wedge plunger 15 Set screw 3 Master jaw 16 Set screw 2 or 4 4 Soft jaw 17 Socket head cap screw 5 T nut 18 Steel ball 6 Plunger...

  • Page 9: Important Safety Precautions

    Important Safety Precautions Important safety precautions are summarized below. Please read this section before first starting to use this product. Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Turn off main power supply before attaching, inspecting or replacing chuck, and before adding oil.
  • Page 10 Important Safety Precautions Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Do not allow the rotation speed of the chuck to exceed the maximum allowable speed limit. (Refer to pages 17-22) For All Users ・...
  • Page 11 Important Safety Precautions Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Keep the height of the jaw within the range specified in the gripping force limit table (Refer to page 21). If you must use a jaw taller than a standard soft jaw, use less than the input (piston thrust force, draw pipe drawing force) specified in the gripping force limit table.
  • Page 12 Important Safety Precautions Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Use of a chuck and cylinder that cannot be used together safely may cause the cylinder to break at high pressure resulting in the chuck and work flying out.
  • Page 13 Important Safety Precautions Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Always tighten the bolts at the specified torque. If the torque is insufficient or excessive, the bolt will break, which is dangerous as the chuck or work will fly out.
  • Page 14 Important Safety Precautions Failure to follow the safety precautions below will result in ！ DANGER serious injury or death. Provide sufficient strength for the draw pipe (Refer to pages 39-41). Provide sufficient screw depth for the draw pipe. Firmly tighten the draw pipe. For Machine Tool Manufactures ・...
  • Page 15 Important Safety Precautions Failure to follow the safety precautions below could result in ！ WARNING serious injury or death. Do not modify the chuck in a way not permitted by the manufacturer. For All Users ・ It may not only break the chuck but the chuck and the work may fly out, which is dangerous.

  • Page 16: Specifications

    3. Specifications 3-1. Specifications ・ BS300 type Table 2 Type BS306 BS308 BS310 Plunger stroke Jaw stroke (in diameter) Allowable maximum 34.8 （2243） input force (kgf) (3549) (4385) 105.8 Maximum static gripping force (kgf) (5610) (8570) (10795) Allowable maximum Rotation speed...
  • Page 17 ・ BS300A type Table 3 Type BS306A5 BS308A6 BS310A6 BS310A8 Plunger stroke Jaw stroke (in diameter) Allowable maximum 34.8 （2243） input force (kgf) (3549) (4385) (4385) Maximum static gripping 105.8 105.8 force (kgf) (5610) (8570) (10795) (10795) Allowable maximum Rotation speed 6000 5000 4200...

  • Page 18: Relationship Between Gripping Force And Rotation Speed

    ・ The attaching bolts of the soft jaw are tightened at the specified torque. (Refer to page ・ The numerical values are obtained with the Kitagawa gripping force meter . The gripping position of the gripping force meter is at a position 1/2 of the height of the soft jaw top surface (height from the chuck surface to the top surface of the jaw).
  • Page 19 ・ The numerical values are obtained by the Kitagawa gripping force meter. The gripping position of the gripping force meter is at a position 1/2 of the height of the soft jaw top surface (height from the chuck surface to the top surface of the jaw).
  • Page 20 Kitagawa gripping force meter is required. Fig.6 ・ In the case of processing a considerably unbalanced work, lower the rotation speed.
  • Page 21 3-3. Relationship between gripping part center height, static griping force and input force / Relationship between top jaw mass moment and gripping force loss If the gripping part center height of the used top jaw (dimension H in Fig. 7) is higher than the gripping part center height of the standard soft jaw, a large load is applied to the master jaw, T nut, jaw attaching bolts, etc.
  • Page 22 Fig.8...
  • Page 23 Analysis of the gripping force, input force and rotation speed using Fig. 8 is carried out as shown below. ・ For example, in the case of BS306 standard soft jaw (mass moment 39kg・mm), it cannot exceed 6000min (rpm), and the gripping force loss due to the centrifugal force at this rotation speed is 36.7kN (approx.

  • Page 24: Forming Soft Jaw

    4. Forming Soft Jaw 4-1. Attachment of soft jaw The attaching position of the soft jaw can be adjusted by loosening the socket head cap screw, attaching the soft jaw and by changing each serration engagement position. Use the most appropriate soft jaw considering the shape, dimension, material, and surface roughness of the work and the cutting conditions, etc.
  • Page 25 ・ If the screw-in depth of the jaw attaching bolt to the T nut is shallow, the T nut will break, and this is dangerous as the jaw and work will fly out. If the attaching bolt is too long and comes out from the bottom of the T nut as well, this is dangerous as the jaw and work will fly out since the top jaw is not fixed.

  • Page 26: Forming Soft Jaw With Outside Diameter Gripping

    4-2. Forming soft jaw with outside diameter gripping 1. Preparation of the plug for forming ・ Prepare the plug for forming. The surface roughness of the plug outside diameter is to be approximately 25s, and make a shape with sufficient thickness which does not distort. ・...

  • Page 27: Forming Soft Jaw With Inside Diameter Gripping

    4-3. Forming soft jaw with inside diameter gripping 1. Preparation of the ring for forming ・ Prepare the ring for forming. The surface roughness of the ring inside diameter is to be approximately 25s, and make a shape with a sufficient thickness which does not distort. ・...

  • Page 28: Forming Method When You Use Forming Jig

    4-4. Forming method when you use forming jig 1. Preparation of the jig for forming ・ Prepare the jig for forming. (There is a commercially available product.) ・ Attach the pin (Example 1) or the bolt and nut (Example 2) by dividing equally into 3 portions onto the ring shape plate.

  • Page 29: Usage

    5. Usage This product is a device to fix a work-piece when it is processed by the lathe machine or the rotary table. The rotary cylinder closes the jaw and fixes a work-piece so that it does not move during processing.

  • Page 30: Precautions Related To Usage Of Jaw

    5-3. Precautions related to usage of jaw ・ If a soft jaw other than one made by Kitagawa Corporation is used, the engagement will be inferior, and the master jaw will be deformed, the gripping precision will worsen, and the work will fly out due to gripping failure, which is dangerous.

  • Page 31: Precautions Related To Processing

    5-4. Precautions related to processing <1> Unbalance ・ In the case of processing largely unbalanced work, lower the rotation speed. The work will fly out and this is dangerous. ・ Vibrations are generated if there is unbalance owing to the work or the jig, etc. Vibration not only will impart a negative influence on the process precision but also the endurance of the chuck being remarkably shortened, and the chuck may break.

  • Page 32: Attachment Of Locator And Jig

    5-5. Attachment of locator and jig ・ In the case of attaching the locator and the jig on the chuck body surface, tap or drill a hole in the additional process range specified in Fig. 12. Fig.12 Table 6 θ Type P(mm) Q(mm)

  • Page 33: Maintenance And Inspection

    Table 7 Genuine Kitagawa genuine product CHUCK GREASE PRO product (Kitagawa distributor of each country) Kitagawa chuck grease Conventional product Molykote EP Grease TORAY Dow Corning (only inside Japan) Conventional Chuck EEZ grease Kitagawa-Northtech Inc.

  • Page 34: Disassembling

    ・ To keep the chuck running in the best condition for a long time, adequate grease lubrication is necessary. Insufficient grease lubrication causes a drop in the gripping force, operation failure at low hydraulic pressure, drop in gripping precision, abnormal wearing, seizing, etc. The work will fly out due to a drop in the gripping force and this is dangerous.
  • Page 35 ・ Use an eyebolt or a hanging belt when attaching and detaching the chuck to and from the machine, as there is a danger of injury or damage if the chuck drops. Chuck size Eyebolt (inch) 6 , 8 , 10 ・...

  • Page 36: Malfunction And Countermeasures

    7. Malfunction and Countermeasures 7-1. In the case of malfunction Check the points specified in the table below and take the appropriate countermeasure. Table 8 Defective Cause Countermeasure The chuck inside will break. Disassemble and replace the broken part. The chuck does not The sliding surface is seized.

  • Page 37: Where To Contact In The Case Of Malfunction

    ・ If the chuck failed due to a seizure or breakage, remove the chuck from the machine, following the disassembly steps in page 33. When the jaws and covers cannot be removed due to a blockage of workpiece, do not disassemble forcibly but please contact us or our agent.

  • Page 38: Attachment

    For Machine Tool Manufactures Following pages are described for machine tool manufacturers (personnel who attach a chuck to a machine). Please read following instruction carefully when you attach or detach a chuck to machine, and please sufficiently understand and follow the instructions for safe operation.
  • Page 39 ・ Attach the manual switching valve at a position where it is easy to operate for the attaching equipment. ・ Install the hydraulic unit at a position where the drain hose is not kinked and the needle of the pressure gauge is easily read. ・...
  • Page 40 8-2. In the case that the back plate must be manufactured 1. Production of draw pipe Determine the length of the draw pipe as shown below. Fig.14 Fig.15 Table 9 Type Cylinder d(f7) e Min f Max -0.025 BS306 S1246 M55×2 M55×2 A+41...
  • Page 41 ・ Provide sufficient strength for the draw pipe. If the draw pipe is broken due to insufficiency of the strength, the gripping force will be lost instantly, which is dangerous as the work will fly out. ・ Keep the dimension e and the dimension f in Fig. 14 for the draw pipe and a material with the tensile strength 380MPa (38kgf/mm ) or more must be used.
  • Page 42 ・ Use the bolts attached to the chuck, and do not use other bolts. However, if you must use other bolts not provided by Kitagawa, use bolts that have at least a strength classification of 12.9 (10.9 for M22 or more) and be sure they are long enough.
  • Page 43 3. Production of back plate ・ Process the engagement diameter of the back plate after measuring the actual spindle. ・ Run-out of the back plate directly affects the process precision. The end surface run-out of the back plate, spigot joint diameter run-out must be 0.005 mm or less. ・...
  • Page 44 ・ Use the bolts attached to the chuck, and do not use other bolts. However, if you must use other bolts not provided by Kitagawa, use bolts that have at least a strength classification of 12.9 (10.9 for M22 or more) and be sure they are long enough.
  • Page 45 8-3. In the case of with back plate Also read “In the case that the back plate must be manufactured” in 8-2 (pages 39-43). 1. Production of draw pipe Determine the length of the draw pipe as shown below. Fig.18 Fig.19 Table 13 Type...

  • Page 46: Attachment Of Chuck

    8-4. Attachment of chuck 1. Attaching the draw pipe to the cylinder ・ Apply adhesive onto the screw part of the draw pipe, and screw it into the piston rod of cylinder. At this time, refer to the instruction manual for the cylinder for tightening torque. ・...
  • Page 47 ・ Use the bolts attached to the chuck, and do not use other bolts. However, if you must use other bolts not provided by Kitagawa, use bolts that have at least a strength classification of 12.9 (10.9 for M22 or more) and be sure they...
  • Page 48 Table 14 Bolt size Tightening torque N・m N・m N・m N・m N・m N・m N・m N・m 5. Adjust the position of the wedge plunger ・ The appropriate position of the wedge plunger at the cylinder forward end is the position when the dimension A in Fig.20 becomes as shown in the table below. ・...

  • Page 49: Other Information

    9. Other information 9-1. About standards and orders This product is based on the following standards or orders. ・ Machinery directive:2006/42/EC Annex I ・ EN ISO 12100:2010 ・ EN1550:1997+A1:2008 9-2. Information about markings of product Fig.21...

  • Page 50: About Disposal

    9-3.About disposal Ultimate disposal of this product should be handled according to all national laws and regulations.
  • Page 52 We also declare that the specific technical documentation for this partly completed machinery was drawn up according to the Supply of Machinery (Safety) Regulations 2008 Annex VII part B. Product : Standard chuck Model : BS300 series (Models BS306, BS308, BS310) Serial number : See original declaration Manufacturer : Kitagawa Corporation...
  • Page 53 The products herein are controlled under Japanese Foreign Exchange and Foreign Trade Control Act. In the event of importing and/or exporting the products, you are obliged to consult KITAGAWA as well as your government for the related regul ation prior to any transaction.

This manual is also suitable for:

Bs306Bs308Bs310Bs306a5Bs308a6Bs310a6 ... Show all

Table of Contents